Starting Your Air Conditioner—Digital Control. Friedrich CP18N30, CP18C30, CP14, CP14N10, CP24N30, Chill CP18, Chill CP24
Add to my manuals
16 Pages
advertisement
Money
Saver
®
POWER
Cool
Fan Only
Mode
Auto Swing
1.
Press POWER to turn on air conditioner.
POWER
NOTE: When the unit is turned on, it will display the previous settings for the Mode, Fan Speed and temperature.
2.
Choose mode. See “Mode.”
3.
Choose fan speed. See “Fan Speed.”
4.
Choose temperature. See “Temperature.”
Mode
1.
Press and hold MODE.
2.
Choose Cool or Fan mode
�
Cool—Cools room. Press FAN SPEED to choose fan speed. Then adjust the temperature by pressing the up or down arrow buttons.
�
Fan—Operates the fan at High speed, without cooling.
The display shows “FO” (fan only).
Money Saver
®
�
Money Saver — Fan and compressor run only when cooling is needed. Turns fan off when room temperature reaches the temperature setting on the thermostat.
Cool
Fan Only
Mode
Starting Your Air Conditioner—Digital Control
Temperature
Timer
Press, or press and hold, the plus button to raise the temperature 1º until it reaches 86ºF (30ºC).
0 F
Temp/Hour
Hr.
High
Med
Low
Fan Speed
0 F
Hr.
Temp/Hour
Money
Saver
®
Fan Speed
NOTE: The Fan Speed button will operate only when the Cool or
Power Saver mode has been selected.
1. Press and hold FAN SPEED until you see the indicator light for the desired setting.
2. Choose High, Medium or Low.
High
Med
Low
Fan Speed
�
Press, or press and hold, the minus button to lower the temperature 1º until it reaches 64ºF (18ºC).
Timer Delay
To set the Timer for a 1- to 24-hour delay until the air conditioner turns off (the air conditioner must be On):
1. Press TIMER. Indicator light will flash.
Timer
2. Press the plus or minus button to change the delay time from
1 to 24 hours.
3. Press TIMER or wait 10 seconds. Indicator light will remain on.
To set the Timer delay for a 1- to 24-hour delay until the air conditioner turns on, keeping previous settings:
1. Turn off air conditioner.
2. Press TIMER. Indicator light will flash.
3. Press the plus or minus button to change the delay time from
1 to 24 hours.
4. Press TIMER or wait 10 seconds. Indicator light will remain on.
To set the Timer delay for a 1- to 24-hour delay until the air conditioner turns on, changing previous settings:
1. Turn on air conditioner.
2. Adjust MODE to desired setting.
3. Adjust FAN SPEED to High, Medium or Low .
4. Adjust temperature between 64ºF (18ºC) and 86ºF (30ºC).
5. Turn off air conditioner.
6. Press TIMER. Indicator light will flash.
7. Press the plus or minus button to change delay time from 1 to
24 hours.
8. Press TIMER or wait 10 seconds.
To clear Timer delay program
NOTE: Air conditioner can be either on or off.
Press and hold TIMER for 3 seconds. Indicator light will turn off.
To see the time remaining (in hours)
1. Press TIMER once after it has been set.
2. While the display is showing the remaining time, you can press the plus or minus button to increase or decrease the time.
12
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 2 Air Conditioner Safety
- 3 Installation Requirements
- 3 Tools and Parts
- 3 Location Requirements
- 4 Electrical Requirements
- 6 Installation Instructions
- 6 Unpacking
- 7 Window Installation (on some models)
- 9 Through-the-Wall Cabinet Installation
- 10 Complete Installation
- 11 Air Conditioner Use
- 12 Starting Your Air Conditioner—Digital Control
- 13 Remote Control Operation
- 13 Normal Sounds
- 14 Air Conditioner Care
- 14 Cleaning the Air Filter
- 14 Cleaning the Front Panel
- 14 Repairing Paint Damage
- 14 Annual Maintenance
- 14 Troubleshooting
- 15 Assistance or Service
- 16 Warranty