Using the Setup Menu. HP PW460t, PW460t Digital Camera, PW-460t

Using the Setup Menu

You can access the Setup menu whether you are in Record or Playback mode.

The Setup menu allows you to configure general camera settings.

To go to Setup Menu:

1. Tap the onscreen Menu button to launch the Record/Playback

Menu.

2. Tap the tab button to launch Setup menu.

3. Tap or to turn pages.

4. Tap the desired option button to enter submenu.

5. Configure the settings in the submenu.

6. Press the onscreen settings.

7. Tap the or menu anytime.

button to save and apply changed

button to exit the menu or return main

Setting Sounds

Use the option buttons to control the sounds produced by the camera.

1. From the Setup menu, tap to select Sounds.

2. Configure settings by tapping the option button.

3. Tap the button to apply.

Icon

Startup

Shutter

Beep

Item

Sound 1,

Sound 2,

Sound 3, Off

On, Off

On, Off

Description

Selects the startup sound when camera is turned on.

Enables or disables shutter sound when Shutter button is pressed.

Shutter sound is not available when recording videos or voice clips.

Enable or disable the beep sound when using touch screen.

66 67

66

Setting Power Save

The Power Save function allows you to set an idle time after which the camera automatically sets to sleep mode to save power. After a minute of being in sleep mode, the camera eventually turns off power.

This function is not available in the following instances:

• Recording a video or audio file

• Playing a slideshow/video/audio file

• Using the USB connector

Setting LCD Save

Enable the LCD Save function to automatically decrease the LCD brightness to conserve battery power. When the camera is idle for 20 seconds, the LCD darkens. Press any button to resume to normal brightness.

• The camera is idle when no buttons are pressed. LCD Save, though enabled, does not function during video playback, slideshow, video recording and Pre-Composition scene mode shooting.

Setting Date & Time

Use the Date & Time function to set the date and time of your camera. This function is useful in attaching date stamps on captured images. Your camera uses a 12-hour time format.

Setting Language

Specify in which language menus and messages are to be displayed on the LCD monitor.

1. Use the navigation control to scroll through the list and select the desired language.

2. Tap your selection to confirm and apply settings.

Setting File Numbering

This function allows you to select the method in which to assign file numbers to images.

Available settings are:

• Series. Assigns number to files in sequence even if the folder is changed.

• Reset. Starts from 0001 each time the folder is changed.

To understand folder and file structure of your camera, see

“About Folder and File Names” on page 73.

67

Setting TV Out

Use the TV Out function to adjust video output signal to accommodate different regional settings. If TV out is not set correctly, the image may not display properly on TV.

Available settings are:

• NTSC.

Applicable in Japan, USA, Canada, Taiwan and others.

• PAL.

Applicable in Europe, Asia (excluding Taiwan), Oceania and others.

Setting LCD Brightness

Select a brightness level for the LCD monitor.

Available settings are:

• Bright

• Normal

68 69

68

Setting Memory Kit

This utility formats the internal memory (or memory card) and erases all stored images and data. If the images were saved in the internal memory, when inserting memory card into the camera, you can use Copy to Card function in order to copy all images from the internal memory into memory card.

Available settings are:

• Format.

Tap to format currently used memory.

• Copy to Card.

Tap to copy all files stored in the internal memory to the memory card.

• If the photos were saved in the internal memory when inserting memory card into the camera, you can use Copy to Card function in order to copy all photos from the internal memory into memory card.

• If there is a memory card inserted in the memory slot, the camera automatically saves all files to the memory card.

• If there is no memory card or the internal memory is empty, the function is disabled.

Copy to Card

Reset All

Use this function to reset the camera to its factory settings.

However, the following settings are exceptions and not affected by Reset.

• Date and Time

• Language

• TV Out

• Custom White Balance data

69