Velleman LEDA200

LEDA200

USER MANUAL

1. Introduction

To all residents of the European Union

Important environmental information about this product

This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm the environment. Do not dispose of the unit (or batteries) as unsorted municipal waste; it should be taken to a specialized company for recycling. This device should be returned to your distributor or to a local recycling service. Respect the local environmental rules.

If in doubt, contact your local waste disposal authorities.

Thank you for choosing Vellight! Please read the manual thoroughly before bringing this device into service. If the device was damaged in transit, don't install or use it and contact your dealer.

2. Safety Instructions

Keep this device away from children and unauthorized users.

This luminaire does not have a built-in device to disconnect it from the electric mains. Make sure to electrically isolate the luminaire before installation or maintenance activities are performed.

DO NOT disassemble or open the cover. There are no userserviceable parts inside the device. Refer to an authorized dealer for service and/or spare parts.

• A qualified technician should install and service this device.

• Make sure that the available voltage does not exceed the voltage stated in the specifications of this manual.

• Do not crimp the power cord and protect it against damage. Have an authorised dealer replace it if necessary.

V. 03 – 22/08/2013 3 ©Velleman nv

3. General Guidelines

LEDA200

Refer to the Velleman® Service and Quality Warranty on the last pages of this manual.

Keep this device away from extreme temperatures.

Protect this device from shocks and abuse. Avoid brute force when operating the device.

This device is not suitable for dimming.

• Familiarise yourself with the functions of the device before actually using it.

• All modifications of the device are forbidden for safety reasons.

Damage caused by user modifications to the device is not covered by the warranty.

• Only use the device for its intended purpose. All other uses may lead to short circuits, burns, electroshocks, lamp explosion, crash, etc. Using the device in an unauthorised way will void the warranty.

• Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and the dealer will not accept responsibility for any ensuing defects or problems.

• Keep this manual for future reference.

4. Features

• illumination of plants, shrubs, garden ornaments, garden paths, etc.

• garden spike spotlight offers a comprehensive range of lighting options

• small unobtrusive exterior fitting offers complete vertical and horizontal adjustment

• makes an ideal, easy to install solution for many landscaping illumination applications

• stainless steel with glass diffuser

• with 30cm power cable

V. 03 – 22/08/2013 4 ©Velleman nv

LEDA200

• IP44 rated

• low power consumption, high power output.

5. Installation

Refer to the illustrations on page 2 of this manual.

1. This luminaire does not have a built-in device to disconnect it from the electric mains. Make sure to electrically isolate the luminaire before installation or maintenance activities are performed.

2. Push the spike into the ground at the desired location.

3. Connect the power cable [1] to a suitable 12V power source.

Make sure there is no strain on the cable; leave sufficient slack.

Warning: if the power cable is damaged, it must be replaced by the manufacturer, his service agent, or a similar qualified person in order to avoid any hazard.

4. Tilt the lamp in the desired angle.

Caution: make sure the power cable is not crimped.

6. Cleaning and maintenance

• All screws should be tight and free of corrosion.

• The electric power supply cables must not show any damage.

Have a qualified technician maintain the device.

• This luminaire does not have a built-in device to disconnect it from the electric mains. Make sure to electrically isolate the luminaire before installation or maintenance activities are performed.

• Wipe the device regularly with a moist, lint-free cloth. Do not use alcohol or solvents.

• There are no user-serviceable parts.

• Contact your dealer for spare parts if necessary.

7. Technical Specifications power supply

LED colour temperature luminous flux dimensions weight

12VDC

1 x 1W high power LED

6500K

140 lm

Ø44 x 82mm (250mm spike included)

440g

V. 03 – 22/08/2013 5 ©Velleman nv