FCC COMPLIANCE

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a specific installation. If interference does occur to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

• Contact customer service or an experienced radio/TV technician for assistance.

Caution: Unauthorized changes or modifications to the equipment may violate FCC regulations and could void the user’s authority to operate the equipment.

BATTERY DISPOSAL

ATTENTION: This device contains a Lithium-Ion battery; never incinerate, puncture, deform, short-circuit, or charge with an inappropriate charger. Fire, explosion, property damage, or bodily harm may occur if this warning is not followed.

This system operates on two Li-Ion battery packs (200mAh capacity for the Collar Receiver and 550mAh capacity for the Remote Transmitter). Only replace with battery received from calling the Customer Care Center at

1-800-732-0144.

Separate collection of spent batteries is required in many regions; check the regulations in your area before discarding spent batteries. Please see below for instructions on how to remove the battery from the product for separate disposal. If you wish to ship us your spent batteries for disposal, contact the Customer Care Center.

AT END OF PRODUCT LIFE, USE THESE BATTERY REMOVAL INSTRUCTIONS FOR FINAL DISPOSAL (DO NOT

OPEN THE COLLAR RECEIVER OR REMOTE TRANSMITTER UNTIL YOU HAVE RECEIVED THE REPLACEMENT):

• Using a #1 Phillips screwdriver for your Remote Transmitter and/or a 3/32 Allen wrench for your Collar Receiver,

remove the case screws.

• Remove the case back or cover.

• Remove the old battery pack. NOTE: When removing the old battery pack, care must be taken when gripping the

connector firmly to avoid damaging the wires. Shorting the battery wires may cause fire or explosion.

NOTE: These instructions are not valid for repair or battery replacement. Replacing the battery with a battery not specifically approved by Radio Systems Corporation may cause fire or explosion. Please call the Customer Care

Center at 1-800-732-0144 to avoid invalidating your warranty.

This product is protected by the following patents:

U.S. Patent Numbers: 6,901,883; 7,017,524; D573,564; 7,420,136; 6,184,790 and other patents pending.

18

400-1053-4.indd 18-19

1-800-732-0144 WWW.SPORTDOG.COM 19

10/28/15 3:04 PM

WETLANDHUNTER

®

SDR::AW ADD-A-DOG

SPORTHUNTER

®

SDR::A ADD-A-DOG

SDR-AH, SDR-AB, SDR-AF, SDR-AS, AND SDR-AC ADD-A-DOG COLLARS ARE COMPATIBLE WITH THIS SYSTEM.

NOTE: SDR-FS, SDR-FH, SDR, SDR-CH, SDR-FC, SDR-BEEP, AND SDR-H ADD-A-DOG COLLARS ARE NOT COMPATIBLE WITH THIS SYSTEM.

©2008, 2015 RADIO SYSTEMS CORPORATION

Radio Systems Corporation • 10427 PetSafe Way • Knoxville, TN 37932 • 1-800-732-0144

400-1053/4

400-1053-4.indd 20-21

DO NOT PRINT

THIS PAGE

The world leader in pet training products

Material: Cover:128g C2S;

Body:100g Wood free paper

Color: White

Printing: Cover: CMYK X 1C body: 1C x 1C

Coating: Cover with Aqueous

Varnish; Cut, fold, 2 saddle stitch, and Bulk Pack

RSC Part #: 400-1053

Description: MANUAL SD-1825

Created by: AR

Initial Creation Date: 12/10/08

Approved by: GG

Date Approved: 12/15/08

Program used: INDESIGN CC

Revision: 004 ECO: RSC10592

Revision Description: TX Charging Light

Revision Date: 10/23/15

10/28/15 3:04 PM