instruction

-J04339 REV. 2015-04-14

SCREAMIN' EAGLE STAGE 1 KIT FOR EFI MODELS

GENERAL

Kit Number

29260-08

Models

Fits all 2008 and later Touring models.

Additional Parts Required

Proper installation of this kit requires the use of Digital Technician ™ at a Harley-Davidson dealer.

This kit requires the separate purchase of Air

Cleaner/Degreaser (99883-88T) which is available from a

Harley-Davidson dealer.

4.

See Figure 1 and Table 1. Remove and discard support

induction module bracket (C).

INSTALLATION

Install Air Cleaner

The element in this kit is specifically designed for use with the OE (original equipment) cover. Using this kit with an air cleaner cover other than the OE cover could lead to failure of the element faceplate. The kit may be used in conjunction with other H-D accessory covers provided the appropriate adapter recommended in those kits is used.

If the element faceplate fails the cover could detach possibly distracting the rider which could result in death or serious injury. (00400b)

The rider's safety depends upon the correct installation of this kit. Use the appropriate service manual procedures.

If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a)

NOTE

This instruction sheet references service manual information.

A service manual for your model motorcycle is required for this installation and is available from a Harley-Davidson dealer.

Kit Contents

See Figure 1 and Table 1.

NOTES

This Stage 1 kit is intended for High Performance applications only. This engine related performance part is legal for sale or use in California on pollution controlled motor vehicles. Engine related performance parts are intended for the experienced rider only.

The air cleaner contained in this kit is designed to perform with this kit only. Any other combination of components is not confirmed to be legal for street use.

REMOVAL

1.

Remove main fuse. Refer to MAIN FUSE REMOVAL in service manual.

2.

Remove existing air cleaner backplate. Refer to AIR

CLEANER: EFI, REMOVAL in service manual. Save stock air cleaner cover and button head screw that secures cover. Discard remaining parts.

3.

Remove fuel tank. Refer to Section 4, FUEL SYSTEM, in service manual.

-J04339

NOTE

When servicing the air cleaner, apply Loctite ® 243 (blue) 99642-

97 to threads of all fasteners.

1.

See Figure 1. Install two O-rings (1) from kit in grooves

around breather screw holes on induction module side of backplate assembly (2). Install two O-rings (1) from kit in grooves in underside of head of breather screws (5).

2.

Peel the protective strip off the gasket (3) and place the adhesive side onto the backplate. Align to the equally spaced screw holes, and position the gasket carefully before firmly pressing the gasket into place.

3.

Insert new breather screws (5) through the backplate.

4.

Apply Loctite 243 (blue) to breather screw threads and mating tapped holes in cylinder head.

5.

Thread screws into cylinder head but do not tighten.

6.

Thread air cleaner mounting studs (4) all the way through the backplate (2) until the screw threads are captured in induction module. Do not tighten completely at this time.

7.

Alternately tighten two breather screws (5) to 120-144 in-

lbs (13.6-16.3 Nm).

8.

Tighten three air cleaner studs (4) to 55-60 in-lbs (6.2-6.8

Nm).

9.

Install fuel tank.

Install Air Cleaner Element and Cover

NOTES

This is a dry air filter. Do not apply oil to the filter element.

Whenever the air cleaner cover is installed, apply Loctite 243

(blue) to the air cleaner cover screw (B).

Many Harley-Davidson ® Parts & Accessories are made of plastics and metals which can be recycled.

Please dispose of materials responsibly.

1 of 3