advertisement
OPTIONS
FLEXTIG
TIG WELD WITH YOUR
SNAP-ON TOOLS MUSCLE MIG SYSTEM
(MM140SL, MM250SL)
The TIG Welding Process is used to produce the highest quality, porosity-free welds. The FLEXTIG adds TIG Welding capabilities to your Snap-on Tools MIG
Welder.
The FLEXTIG is designed for Tungsten-Inert Gas (TIG) welding with Direct
Current, Straight Polarity (DCSP) on steel, stainless steel, chrome-moly, copper or cast iron (18 Ga. minimum plate thickness).
THE FLEXTIG WILL NOT WELD ALUMINUM.
The FLEXTIG consists of a 200 amp, gas cooled torch with built-in gas control valve and remote on-off switch, 12-1/2 or 25 foot cable assembly and accessories required for putting the unit in service.
1 each
1 each
1 each
SPECIFICATIONS
Part Number ........................ FLEXTIG 12 (12-1/2' cable)
FLEXTIG 25 (25' cable)
Torch Rating ....................... 200 Amps, DCSP
Duty Cycle ........................... 100% (reduce duty cycle when operating over 200 amps.)
Cooling Method ................... Gas(100% ARGON)
Shielding Gas
Control Method ............... Gas Valve on Torch
Welding Current
On-Off Control ................ Locking Switch onTorch
1 each
3 each
3 each
2 each
2 each
2 each
6 each
2 each
1 each
3 each
3 each
CONTENTS OF FLEXTIG
TIG Torch with built-in valve
Locking Electric Switch with cord & plug
(installed on torch)
12-1/2 foot Power Cable with Connector
(installed on torch)
15 foot Gas Hose with fitting
(installed on torch)
3C116 Collet - for 1/16" tungsten
3C332 Collet - for 3/32" tungsten
3CB116 Collet Body - for 1/16" tungsten
3CB332 Collet Body - for 3/32" tungsten
3C6 Gas Cup - 3/8" orifice
3C7 Gas Cup - 7/16" orifice
3C8 Gas Cup - 1/2" orifice
300L Long Backcap
1/16" X 3" Tungsten Electrode
3/32" X 3" Tungsten Electrode
MHG5-B
ONE POUND SPOOL GUN
FOR ALUMINUM MIG WELDING
WITH SNAP-ON TOOLS
MUSCLE MIG SYSTEMS
(MM140SL, MM250SL)
The MHG5-B (Motorized Hand Gun System) is a compact, light-in-weight, easy to operate MIG welding system designed for aluminum welding. It will feed .023" Thru 3/64" diameter wire from 4 inch spools. The standard equipment cable is 25 feet in length. 35 foot and 50 foot cables are optional.
The wire speed control knob is built into the gun handle.
With the following options, the MHG5-B can also be used to weld steel or stainless steel (.030"-.035" diameter wire size).
SN-2160K Knurled Drive Roll for .030 - .035" steel wire
M5-T30 Contact tip - for .030" steel wire or M5-T35 Contact tip - for .035" steel wire
SPECIFICATIONS
Part Number ....................... MHG5-B
Gun Rating ......................... 200 Amps @ 100% duty cycle
250 Amps @ 60% duty cycle
Wire Feed Speed Range ... 50 to 650 inches per minute
Cooling Method .................. Air (gas)
1 each
1 each
MHG5-B SYSTEM COMPONENTS
MHG-5 Spool Gun (only)
HGC9-25 Hand Gun Cable Assembly with fittings - 25 feet length
7 each
1 each
1 each
MG-TXX Contact Tip(1 installed in gun)
2 - .030 (MG-T30)
3 - .035 (MG-T35)
2 - 3/64 (MG-T364)
M35-NA62 Nozzle Assembly
(installed on gun)
M35-D Gas Diffuser
(installed on gun)
24 Snap-on Tools Corporation Kenosha, WI 53141-1410
advertisement
Related manuals
advertisement
Table of contents
- 3 INTRODUCTION
- 4 DESCRIPTION, SPECIFICATIONS
- 5 CHECK LIST (CONTENTS)
- 6 INSTALLATION & ELECTRICAL REQUIREMENTS
- 10 OPERATION
- 15 MAINTENANCE
- 17 TROUBLE SHOOTING CHART
- 22 CONNECTING FLEXTIG OR SPOOL GUN
- 23 LINER INSTALLATION
- 24 PARTS BREAKDOWN - MIG TORCH
- 26 OPTIONS - FLEXTIG OR SPOOL GUN
- 27 PARAMETER CHARTS