- Computers & electronics
- Audio & home theatre
- TV set-top boxes
- Satellite antennas
- Sea Tel
- 9497B-1
- Installation and Operation Manual
advertisement
9497B-1 Technical Specifications 9497B-1 C/Ku-Band TVRO
8.6.
Environmental Conditions (ADE)
Temperature: -20 degrees C to 55 degrees C.
Humidity:
Spray:
Icing:
Rain:
Wind:
Vibration:
Frequency Range, Hz
4 - 10
10 - 15
15 - 25
25 - 33
Corrosion
Up to l00% @ 40 degrees C, Non-condensing.
Resistant to water penetration sprayed from any direction.
Survive ice loads of 4.5 pounds per square foot. Degraded RF performance will occur under icing conditions.
Up to 4 inches per hour. Degraded RF performance may occur when the radome surface is wet.
Withstand relative average winds up to 100 MPH from any direction.
Withstand externally imposed vibrations in all 3 axes, having displacement amplitudes as follows:
Peak Single Amplitude
0.100 inches (0.1G to 1.0G)
0.030 inches (0.3G to 0.7G)
0.016 inches (0.4G to 1.0G)
0.009 inches (0.6G to 1.0G)
Parts are corrosion resistant or are treated to endure effects of salt air and salt spray. The equipment is specifically designed and manufactured for marine use.
8.7.
Cables
8.7.1.
Antenna Control Cable (Provided from ACU-MUX)
RS-422 Pedestal Interface
Type Shielded Twisted Pairs
Number of wires
Wire Gauge
Communications Parameters:
Interface Protocol:
Interface Connector:
24 AWG or larger
9600 Baud, 8 bits, No parity
RS-422
DE-9P
8.7.2.
Antenna L-Band TVRO IF Coax Cables (Customer Furnished)
2, 4 or 6 cables are required dependant upon which feed/LNB configuration your antenna is fitted with.
Due to the dB losses across the length of the RF coaxes at L-Band, Sea Tel recommends the following 75 ohm coax cable types (and their equivalent conductor size) for our standard pedestal installations:
Run Length Coax Type Conductor Size up to 75 ft up to 150 ft up to 200 ft
LMR-300-75
RG-11 or LMR-400-75
LDF4-75 Heliax
18 AWG
14 AWG
10 AWG
Up to 300 ft LMR-600-75 6 AWG
For runs longer that 300 feet, Sea Tel recommends Single-mode Fiber Optic Cables with Fiber Optic converters.
8-4
9497B-1 C/Ku-Band TVRO 9497B-1 Technical Specifications
8.7.3.
AC Power Cable Above Decks (Customer Furnished)
Voltage: 110 or 220 volts AC, 50/60 Hz., single phase
Power: 100 Watts MAX, pedestal only
8.7.4.
Gyro Compass Interface Cable (Customer Furnished)
Type: Multi-conductor, Shielded
Number of wires
Wire Gauge:
Insulation:
4 Conductors for Step-By-Step Gyro, 5 Conductors for Synchro see Multi-conductor Cables spec above
600 VAC
8.7.5.
Fiber Optic Transmitter (CFE Optional)
Model: Ortel Model 3112A
Frequency Range:
Noise Figure:
Impedance:
Connectors:
RF
Fiber
950-2050 MHz
45 dB
75 ohm
Type F
FC/APC "Tight Fit”
8-5
9497B-1 Technical Specifications
This Page Intentionally Left Blank
9497B-1 C/Ku-Band TVRO
8-6
advertisement
Related manuals
advertisement
Table of contents
- 9 General System Description
- 9 Purpose
- 9 System Components
- 10 General scope of this manual
- 10 Quick Overview of contents
- 11 System Power-up
- 11 Antenna Initialization
- 11 Antenna Stabilization
- 11 Stabilized Pedestal Assembly Operation
- 11 Tracking Operation
- 11 Antenna Polarization Operation
- 12 Low Noise Block Converter Operation
- 12 Radome Assembly Operation
- 13 Satellite Basics
- 13 C-Band Receive Frequency (3.625-4.2GHz)
- 13 Ku-Band Receive Frequency (10.95-12.75GHz)
- 13 Blockage
- 13 Rain Fade
- 13 Signal level
- 14 Satellite Footprints
- 14 Linear Satellite polarization
- 14 Antenna Basics
- 14 Unlimited Azimuth
- 14 Elevation
- 15 Feed Assembly
- 15 Antenna polarization
- 15 Stabilization
- 15 Search Pattern
- 15 Tracking Receiver - Satellite Identification Receiver
- 15 Tracking
- 16 Components of the System Configuration
- 17 Antenna ADE Assembly
- 17 Antenna Control Unit
- 18 Above Decks AC Power Supply
- 18 Satellite Receivers
- 18 Television/Monitor
- 18 Matrix Switch
- 19 General Cautions & Warnings
- 20 Site Survey
- 20 Preparing For The Installation
- 20 Unpack Shipping Crates
- 20 Inspect / Inventory
- 20 Prepare ADE Mounting Location
- 20 Preparing BDE Location
- 20 Installing The System Cables
- 20 4.4. Assembling the ADE
- 21 126” Radome, Baseframe and Antenna Pedestal System Assembly
- 24 144” Radome, Baseframe and Antenna Pedestal System Assembly
- 25 Preparing the ADE for Lift
- 25 Installing The ADE
- 25 Hoist
- 26 Install Antenna/Radome/Baseframe
- 26 Install BDE Equipment
- 26 4.6.1. ACU & TMS
- 26 4.6.2. Other BDE Equipment
- 26 Cable Terminations
- 26 At The Radome
- 26 ACU & TMS
- 26 Other BDE Equipment
- 26 Final Assembly
- 26 Remove Stow Braces/Restraints
- 26 Verify all assembly and Wiring connections
- 26 Balance Antenna Pedestal
- 26 Power-Up The ADE
- 26 Initialization
- 27 Home Flag Position
- 27 BDE
- 27 Setup
- 29 Operator Settings
- 29 AUTO TRIM
- 29 Manually Optimizing Targeting
- 30 Sat Skew setting
- 30 Polarity Angle (POLANG) Parameters
- 30 Optimizing Auto-Polarization Cross-Pol Isolation
- 30 Calibrating Relative Antenna Position (Home Flag Offset)
- 31 5.4.1. To Calculate HFO:
- 32 To Enter the HFO value:
- 33 Radiation Hazard and Blockage Mapping (AZ LIMIT parameters)
- 33 TX Polarity Setup
- 33 TRACK DISP
- 34 ACU Factory Default Parameter Settings – Series 97B & 00B Antennas
- 35 ACU / Antenna System Check
- 35 Latitude/Longitude Auto-Update check
- 35 Ship Heading – Gyro Compass Following Check
- 35 Azimuth & Elevation Drive
- 35 Four Quadrant Tracking Test
- 36 Blockage Simulation Test
- 37 Warranty Information
- 37 Recommended Preventive Maintenance
- 37 Check ACU Parameters
- 37 Latitude/Longitude Auto-Update check
- 37 Heading Following
- 38 Azimuth & Elevation Drive
- 38 Test Tracking
- 38 Visual Inspection - Radome & Pedestal
- 38 Mechanical Checks
- 38 Check Balance
- 38 Observe Antenna Initialization
- 38 Troubleshooting
- 38 Theory Of Stabilization Operation
- 39 Series 97B-1 1C(Linear/Circular)/1Ku (Linear only) TVRO RF Flow
- 39 Antenna Initialization (Series 97B & Series 00 )
- 40 Troubleshooting using DacRemP
- 41 Antenna Loop Error Monitoring
- 42 Reference Sensor Monitoring
- 44 Open Loop Rate Sensor Monitoring
- 45 Open Loop Motor Test
- 45 To Disable/Enable DishScan
- 45 Satellite Reference Mode
- 46 To Read/Decode an ACU Error Code 0008 (Pedestal Function Error):
- 48 Remote GPS LAT/LON Position:
- 50 7.4. Maintenance
- 50 Balancing the Antenna
- 51 Linear/Circular Mode Selection Verification and Alignment
- 53 To Adjust Tilt:
- 55 To Reset/Reinitialize the Antenna:
- 56 Pedestal Control Unit Configuration (xx97B & xx00)
- 56 7.5.1. To configure the PCU;
- 56 7.5.2. MODEL CONFIGURATION NUMBERS
- 56 Antenna Stowing Procedure
- 59 9497 Antenna Reflector
- 59 Feed Assemblies
- 59 TVRO-1 C/Ku Linear/Circular Feed Assembly
- 60 Stabilized Antenna Pedestal Assembly
- 61 126” Radome Assembly
- 61 144” Radome Assembly
- 62 Environmental Conditions (ADE)
- 62 Cables
- 62 Antenna Control Cable (Provided from ACU-MUX)
- 62 Antenna L-Band TVRO IF Coax Cables (Customer Furnished)
- 63 AC Power Cable Above Decks (Customer Furnished)
- 63 Gyro Compass Interface Cable (Customer Furnished)
- 63 Fiber Optic Transmitter (CFE Optional)
- 65 9.1. Model Specific Drawings
- 65 9.2. Series 97B & 00B General Drawings