WIRELESS PROGRAMMING. Merlin Entrylift MT50EVO

Merlin Entrylift MT50EVO is a sectional garage door opener designed for residential use. It has a range of features that make it a convenient and reliable choice for automating your garage door.

Some of the key capabilities of the MT50EVO include:

Automatic obstacle detection: The opener is equipped with a safety reverse system that automatically reverses the door if it encounters an obstacle in its path. This helps to prevent accidents and damage to your garage door or property.
Adjustable force settings: The opener's force settings can be adjusted to ensure that it operates smoothly and safely, even with heavy doors.

PDF

مستند

WIRELESS PROGRAMMING (OPTIONAL ACCESSORIES)

Activate the opener only when door is in full view, free of obstruction and properly adjusted. No one should enter or leave garage while door is in motion. Do not allow children to operate push button(s) or remote(s).

Do not allow children to play near the door.

NOTE: The transmitter(s) supplied with your opener are preprogrammed by the factory.

If you purchase additional transmitters, the garage door opener must be programmed to accept the new remote code.

Program the Receiver to Match Additional Transmitter Codes:

Using the “S” SAVE Button

1.Press and Hold the button on the hand-held remote or wall button that you wish to use (1).

2.Press and release the “S” button on the opener (2).

3.Release the remote button when the opener light flashes. It has learnt the code. If you release the remote control push button before the opener light flashes, the opener has not learned the code.

Now the opener will operate when the remote control push button is pressed.

To Erase all Remote Control Codes

1.Press and Hold the “S” button on the opener until the indicator LED goes ON, and continue holding for approx. 8 seconds, until the indicator LED goes out.

2.Release the button, all codes are now erased.

3 2 2 1

2 3

Locate the

“S” button

Press and release the “S” button

Wireless Keypad E840M

To set the keyless entry PIN:

1.Locate the “S” button on the garage door opener.

2.Press and release the “S” button. The LED 1 indicator light will glow steadily.

3.Enter a 4-digit personal identification number (PIN) of your choice on the keypad.

4.Press and hold the ENTER button. Check to see if the opener light flashes. Release the ENTER button after the light flashes.

To change an existing keyless entry PIN:

1.Enter the existing programmed PIN that you want to change.

2.Press and hold the # button until the courtesy light flashes once.

3.Enter the new 4-digit PIN of your choice, then press the ENTER button. The light will flash once.

4.To test, enter the new PIN, then press the ENTER button. The garage door opener will activate.

Enter a 4-digit

PIN of your choice

Press and hold the enter button

Opener light flashes

After the lights flash release the

ENTER button

مرحباً! أنا روبوت دردشة يعمل بالذكاء الاصطناعي تم تدريبي خصيصًا لمساعدتك في WIRELESS PROGRAMMING. Merlin Entrylift MT50EVO. لقد قمت بمراجعة المستند بدقة ويمكنني مساعدتك في تحديد موقع المعلومات التي تحتاجها بالضبط أو شرح المحتوى بعبارات واضحة و بسيطة. سواء كنت تبحث عن إرشادات حول ميزات معينة أو خطوات استكشاف الأخطاء وإصلاحها أو الاستخدام العام، فلا تتردد في طرح أسئلتك. كلما قدمت المزيد من التفاصيل حول مخاوفك أو احتياجاتك، زادت دقة و فعالية مساعدتي لك!