Chapter 3

Operating Basics

This chapter describes the basic operations of your computer, highlights the precautions that should be taken when using it.

TOSHIBA Dual Pointing Device

Some models are equipped with a dual point system: a Touch Pad and an

AccuPoint pointing stick.

Using the Touch Pad

To use the Touch Pad, simply touch and move your fingertip across it in the direction you want the on-screen pointer to go.

Figure 3-1 Touch Pad and Touch Pad control buttons (R850)

6

5

4

5

2

3

1

1. AccuPoint*

2. AccuPoint control buttons*

3. Touch Pad

* Provided with some models.

4. Fingerprint Sensor*

5. Touch Pad control buttons

6. Touch Pad ON/OFF button

Pressing the Touch Pad ON/OFF button enables or disables the Touch

Pad function.

The two buttons below the Touch Pad are used like the buttons on a standard mouse - press the left button to select a menu item or to manipulate text or graphics designated by the pointer, and press the right button to display a menu or other function depending on the software you are using.

Using the AccuPoint

To use the AccuPoint, simply push it with your finger tip in the direction you want to move the on-screen pointer.

User's Manual 3-1

Two buttons above the Touch Pad work in the same way with the

AccuPoint as they do with the Touch Pad. Refer to the

Using the Touch

Pad section for details.

Some models are equipped with an AccuPoint.

AccuPoint precautions

Certain conditions can affect the on-screen pointer when using AccuPoint.

For example, the pointer may travel contrary to AccuPoint operation or an error message may appear, if

You touch the AccuPoint during power-up.

You apply constant, soft pressure during power-up.

There is a sudden temperature change.

Strong stress is applied to the AccuPoint.

If an error message appears, reboot the computer. If an error message does not appear, wait a moment for the pointer to stop, then continue operation.

Replacing the cap

The AccuPoint cap is an expendable item that should be replaced after prolonged use. The spare AccuPoint cap is supplied with some models.

1.

To remove the AccuPoint cap, firmly pinch the cap and pull it straight up.

Figure 3-2 Removing the AccuPoint cap (R850)

1

1. AccuPoint cap

2.

Position a new cap on the peg and press it into place.

The peg is square, so be careful to align the cap’s square hole with the peg.

The Keyboard

The computer’s keyboard layouts are compatible with a 104/105-key enhanced keyboard - by pressing some keys in combination, all of the

104/105-key enhanced keyboard functions can be performed on the computer.

User's Manual 3-2

The number of keys available on your keyboard will depend on which country/region your computer is configured for, with keyboards being available for numerous languages.

In use there are six different types of keys, specifically typewriter keys, function keys, soft keys, Hot keys, Windows special keys and the keypad overlay.

Never remove the key caps on your keyboard. Doing so could cause damage to the parts under the key caps.

Keyboard indicators

The following figure shows the position of the CAPS LOCK indicator which shows the following conditions:

When the CAPS LOCK indicator glows, the keyboard will produce capitals when any letter is typed.

Figure 3-3 CAPS LOCK indicator (R830)

1

1. CAPS LOCK indicator

CAPS LOCK This indicator glows green when letter keys are locked into their uppercase format.

Function keys: F1 … F12

The function keys (not to be confused with the special FN key) are the twelve keys at the top of your keyboard - these keys function differently from other keys.

User's Manual

F1 through F12 are called function keys because they execute programmed functions when pressed and, when used in combination with

3-3

the FN key, those keys marked with icons also execute specific functions on the computer.

Soft keys: FN key combinations

The FN (function) is used in combination with other keys to form soft keys.

Soft keys are key combinations that enable, disable or configure specific features.

Please note that some software may disable or interfere with soft-key operations, and that the soft-key settings are not restored when the computer returns from Sleep Mode.

This computer's keyboard is designed to provide all the features of the 104key enhanced keyboard.

Since the keyboard is smaller and has fewer keys, some of the enhanced keyboard functions must be simulated using two keys instead of one on the larger keyboard.

The FN key can be combined with the following keys to simulate functions similar to those of keys on the 104/105 key enhanced keyboard which are not on this computer's keyboard.

Press FN + F10 or FN + F11 to access the computer's integrated keypad. When activated, the keys with grey markings on their bottom edge become either numeric keypad keys (FN + F11) or cursor control keys (FN + F10).

Press FN + F12 (ScrLock) to lock the cursor on a specific line. The power on default is off.

Press FN + ENTER to simulate ENTER on the enhanced keyboard’s numeric keypad.

This function is supported with some models.

Hot key functions

Hot key functions let you enable or disable certain features of the computer. The Hot key functions can be performed using either the Hot

Key Cards or by pressing the associated Hot keys (pressing FN + a function or ESC key).

Hot Key Cards

The Hot Key Cards are normally hidden from view. The Cards appear when you press the FN key.

To use the Hot Key Cards:

1.

Press and hold the FN key. The TOSHIBA Flash Cards appear along the top of the screen.

User's Manual 3-4

User's Manual

2.

Select the desired option.

The selected Card is displayed full-size with its available options below it. All other Cards are again hidden from view.

3.

Click the desired option.

To use a Hot Key Card using a hot key:

1.

Press and hold the FN key.

2.

Press the hot key associated with the desired function. The associated hot key card appears at the top of the screen with its available options below it.

3.

To cycle through the displayed options, hold down FN and press the hot key repeatedly. Release the FN key when the desired option is selected.

For more information, please refer to the TOSHIBA Flash Cards Help file.

To access this help, click Start -> All Programs -> TOSHIBA -> Utilities -

> Flash Cards - Help.

Hot keys

This section describes the associated functions of the hot keys.

Mute

Pressing FN + ESC turns the volume on and off.

Lock

Pressing FN + F1 enters ''Lock computer mode''. To restore your desktop, you need to log on again.

Power Plan

Pressing FN + F2 changes the power settings.

Sleep

Pressing FN + F3 switches the system to Sleep Mode.

Hibernate

Pressing FN + F4 switches the system to Hibernation Mode.

Output

Pressing FN + F5 changes the active display device.

To use a simultaneous mode, you must set the resolution of the internal display panel to match the resolution of the external display device.

Brightness Down

Pressing FN + F6 decreases the computer's display panel brightness in individual steps.

Brightness Up

Pressing FN + F7 increases the computer's display panel brightness in individual steps.

Wireless

Pressing FN + F8 switches the active wireless devices.

3-5

If no wireless communication device is installed, no dialog box will appear.

Touch Pad

Pressing FN + F9 enables or disables the Touch Pad function.

Zoom (Display resolution)

Pressing FN + Space changes the display resolution.

ODD

Pressing FN + TAB ejects the disc tray.

Reduce

Pressing FN + 1 reduces the icon size on the desktop or the font sizes within one of the supported application windows.

Enlarge

Pressing FN + 2 enlarges the icon size on the desktop or the font sizes within one of the supported application windows.

Volume down

Pressing FN + 3 decreases the volume in increment.

Volume up

Pressing FN + 4 increases the volume in increment.

FN Sticky key

You can use the TOSHIBA Accessibility Utility to make the FN key sticky, that is, you can press it once, release it, and then press an "F Number" key. To start the TOSHIBA Accessibility utility, click Start -> All Programs

-> TOSHIBA -> Utilities -> Accessibility.

Windows special keys

The keyboard provides two keys that have special functions in Windows, the Windows Start Button key activates the Start menu while the application key has the same function as the secondary (right) mouse button.

This key activates the Windows Start menu.

This key has the same function as the secondary (right) mouse button.

Keypad overlay

This function is supported with some models.

Your computer's keyboard may not have a separate numeric keypad but includes a numeric keypad overlay which functions like one - this is located in the center of the keyboard with the relevant keys having grey letters at

User's Manual 3-6

User's Manual their front edge. The overlay provides the same function as the numeric keypad on a standard 104/105-key enhanced keyboard.

Turning on the overlays

The numeric keypad overlay can be used for numeric data input or cursor and page control.

Arrow Mode

To turn on Arrow Mode, press FN + F10 - the Arrow Mode indicator lights and you are able to access cursor and page control functions by using the keys. You are able to press FN + F10 again to turn off this overlay function.

Numeric Mode

To turn on Numeric Mode, press FN + F11 - the Numeric Mode indicator lights and you are able to access numeric characters by using the keys.

You are able to press FN + F11 again to turn off this overlay function.

Temporarily using normal keyboard (overlay on)

While using the overlay, you can temporarily access the normal keyboard functions without having to turn the overlay off:

1.

Hold down FN key and press any other key - this key will operate as if the overlay were off.

2.

Type upper-case characters by holding down FN + SHIFT and pressing a character key.

3.

Release FN key to continue using the selected overlay function.

Temporarily using overlay (overlay off)

While using the normal keyboard function, you can temporarily use the keypad overlay without having to turn it on:

1.

Hold down FN key.

2.

Check the keyboard indicators as pressing the FN key will turn on the most recently used overlay function - if the Numeric Mode indicator lights you can use the overlay for numeric entry, while if the Arrow

Mode indicator lights, you can use the overlay for cursor and page control function.

3.

Release FN key to return to normal keyboard operation.

Temporarily changing modes

If the computer is in Numeric Mode, you can switch temporarily to Arrow

Mode by pressing a SHIFT key, while if it is in Arrow Mode, you can switch temporarily to Numeric Mode by also pressing a SHIFT key.

3-7

Generating ASCII characters

Not all ASCII characters can be generated using normal keyboard operation, but you are able to generate these characters using their specific ASCII codes.

1.

Hold down ALT with the overlay on or ALT + FN with overlay off.

2.

Using the overlay keys, type the ASCII code of the character you require.

3.

Release ALT or ALT + FN - the ASCII character will appear on the display screen.

Using the Fingerprint Sensor

This product has a fingerprint utility installed for the purpose of enrolling and recognizing fingerprints. By enrolling the ID and password onto the fingerprint authentication feature, it is no longer necessary to input the password from the keyboard. Fingerprint feature enables you to:

Logon to Windows and access a security enabled homepage through

Internet Explorer.

Files and folders can be encrypted/decrypted and third party access to them prevented.

Unlock the password-protected screen-saver.

Authentication of the User Password (and, if applicable, the HDD

(Hard Disk Drive) Password) when booting up the computer (boot authentication).

Single Sign-On feature

Fingerprint cannot be used in models that do not have a fingerprint module installed.

How to Swipe your Finger

Using the following steps when swiping fingers for fingerprint registration or authentication will help to minimize authentication failures:

Align the first joint of the finger to the center of the sensor. Lightly touch the sensor and swipe finger levelly towards you until the sensor surface becomes visible. In performing this process, you should also take care to ensure that the center of your fingerprint is on the sensor.

The following illustrations show the recommended way to swipe your finger over the fingerprint sensor.

User's Manual 3-8

Figure 3-6 Swipe the finger

1

1

1. Sensor

Avoid swiping with your finger stiff or pressed too hard onto the sensor, and take care to ensure that the center of the fingerprint is touching the sensor before swiping. Either of these conditions may cause fingerprint reading to fail.

Check the center of the fingerprint whorl before swiping and then ensure this is swiped along the center line of the sensor.

There is a possibility of authentication failures if the finger is swiped too quickly or too slowly - follow any on-screen instructions to adjust the speed used during the swipe process.

Points to note about the Fingerprint Sensor

Please be aware of the following considerations when using the fingerprint sensor. A failure to follow these guidelines might result in damage to the sensor, sensor failure, fingerprint recognition problems or a lower fingerprint recognition success rate.

Do not scratch or poke the sensor with your nails or any hard or sharp objects.

Do not press the sensor strongly.

Do not touch the sensor with a wet finger or any wet objects - keep the sensor surface dry and free from water vapor.

Do not touch the sensor with a soiled or dirty finger as minute foreign particles of dust and dirt may scratch it.

Do not paste stickers or write on the sensor.

Do not touch the sensor with a finger or any other object which may have a build-up of static electricity on it.

Observe the following before you place your finger on the sensor whether for fingerprint enrollment/registration or recognition.

Wash and dry your hands thoroughly.

Remove static electricity from your fingers by touching any metal surface. Static electricity is a common cause of sensor failures, especially when the weather is dry.

User's Manual 3-9

Clean the sensor with a lint-free cloth - do not use detergent or any other chemicals to clean the sensor.

Avoid the following finger conditions for enrollment or recognition as they may result in fingerprint enrollment errors or a drop in the fingerprint recognition success rate

Soaked or swollen finger, for example as may occur after taking a bath.

Injured finger

Wet finger

Soiled or oily finger

Extremely dry skin condition on finger

Observe the following to improve the fingerprint recognition success rate.

Enroll two or more fingers.

Enroll additional fingers if a recognition failure often occurs when using already enrolled fingers.

Check the condition of your finger - any conditions which have changed since enrollment, such as injury, rough skin, and extremely dry, wet, soiled, dirty, oily, soaked or swollen fingers, may lower the recognition success rate. Also if the fingerprint is worn down or the finger becomes thinner or fatter, the recognition success rate may be lowered.

As the fingerprint for each finger is different and unique you should ensure that only the registered or enrolled fingerprint or fingerprints are used for identification.

Check the position and speed at which you swipe your finger across the sensor - please refer to the preceding drawing.

The fingerprint sensor compares and analyzes the unique characteristics in a fingerprint. However, there may be instances where certain users are unable to register their fingerprints due to insufficient unique characteristics in their fingerprints.

The recognition success rate may differ from user to user.

Points to note about Fingerprint Utility

If Windows 7 file encryption function EFS (Encryption File System) is used to encrypt a file, the file cannot be further encrypted using the encryption function of this software.

You can back up the fingerprint data or the information registered to

Automatic password input in IE.

Please use Import/Export on TOSHIBA Fingerprint Utility main menu.

Please also refer to the fingerprint utility Help file for more information.

You can start it using the following method:

Click Start -> All Programs -> TOSHIBA -> Utilities -> TOSHIBA

Fingerprint Utility. The main screen is displayed. Click ? in the lower left corner of the screen.

User's Manual 3-10

Fingerprint utility limitations

TOSHIBA does not guarantee that the fingerprint utility technology will be completely secure or error-free, or that it will accurately screen out unauthorized users at all times. TOSHIBA is not liable for any failure or damage that might arise out of the use of the fingerprint software.

The fingerprint sensor compares and analyzes the unique characteristics in a fingerprint. However, there may be instances where certain users are unable to register their fingerprints due to insufficient unique characteristics in their fingerprints.

The recognition success rate may differ from user to user.

Setup Fingerprint Registration

Please use the following procedure when first using fingerprint authentication.

In use, the fingerprint authentication system will use the same username and password as defined within the Windows operating system. If no Windows password has been configured, you must do this before starting the fingerprint registration process.

This sensor has the memory space for at least twenty fingerprint patterns. You might be able to register more fingerprint patterns depending on the sensor memory usage.

1.

Click Start -> All Programs -> TOSHIBA -> Utilities -> TOSHIBA

Fingerprint Utility, or click the Fingerprint utility icon in the Taskbar.

2.

The Enroll screen is displayed. Enter the current account password into the Windows Password field. If no Windows password has been configured, you will be asked to configure the new logon password.

Then click Next.

3.

Click the non-enrolled finger icon above the finger you want to register and then click Next.

4.

The note for enrollment operation screen is displayed. Confirm the message and then click Next.

5.

The scanning practice screen is displayed. You are able to practice swiping (three times) your finger to ensure you use the correct method. When you have finished practicing swiping your finger, click

Next.

6.

Swipe three times with the same finger. If scanning of fingerprint succeeds, "Enrollment succeeded! Do you want to save this fingerprint?" message box will appear. Click OK.

7.

The following message will be displayed: "It’s strongly recommended you enroll one more fingerprint.". Click OK and repeat Step 3, 4, 5 and

6 with another finger.

User's Manual 3-11

It is strongly recommended that you register 2 or more fingerprints.

You cannot enroll the same fingerprint more than once, even on a different user account.

Delete the Fingerprint Data

Saved fingerprint data is stored in special non-volatile memory inside the fingerprint sensor. Therefore, if you give the computer to someone else, or dispose of it in any way, the following process is recommended to delete your fingerprint information:

Delete the fingerprint data for the currently logged in user

1.

Click Start -> All Programs -> TOSHIBA -> Utilities -> TOSHIBA

Fingerprint Utility, or double click the utility icon in the Taskbar.

2.

Swipe your finger across the fingerprint sensor.

3.

The TOSHIBA Fingerprint Utility main menu is displayed. Select

Enroll in the main menu.

4.

In the Enroll window, it enables you to delete the fingerprint data for the currently logged in user. Click an enrolled finger you want to delete. "Are you sure you want to delete this fingerprint template?" message box will appear on the screen and then click OK. If you want to delete other fingerprints, repeat this step. If only one fingerprint is registered, the message "Sorry! At least one fingerprint is required." will appear after clicking OK. You are not allowed to delete a unique fingerprint.

5.

Click Close.

6.

"Are you sure you want to quit?" is displayed. Click OK. It will be returned to the TOSHIBA Fingerprint Utility main menu.

Delete all users fingerprints

1.

In the TOSHIBA Fingerprint Utility main menu, click Run as

administrator in the lower left.

2.

User Account Control window is displayed. Click Yes.

3.

Swipe your enrolled finger.

4.

Select Fingerprint Control option.

5.

A list of fingerprint information for all users is shown in the screen.

Click Delete All in the lower right.

6.

"Are you sure you want to delete all fingerprints?" message box will appear on the screen. Click OK.

7.

Click Close.

8.

"Are you sure you want to quit?" is displayed. Click OK. It will be returned to the TOSHIBA Fingerprint Utility main menu.

User's Manual 3-12

Windows Logon via Fingerprint Authentication

In place of the usual Windows logon by ID and password, fingerprint authentication also allows logon to Windows.

This is useful especially when many users are using the PCs, as user selection can be skipped.

Fingerprint Authentication Procedure

1.

Start up the computer.

2.

The Logon Authorization screen is displayed. Choose any of the enrolled fingers and swipe the fingerprint on the sensor. If authentication is successful, the user will be logged on to Windows.

If the fingerprint authentication fails, please logon using the Windows logon password.

A warning message will be displayed when authentication is abnormal or authentication is not successful within a fixed duration.

Fingerprint boot authentication and Single Sign-on feature

Overview about Fingerprint boot authentication

The fingerprint authentication system can be used to replace the keyboard based User Password authentication system when booting up.

If you do not want to use the fingerprint authentication system for password authentication when booting up, but prefer to use the keyboard-based system instead, click the user’s tile when the Fingerprint System

Authentication screen is displayed. This will switch the password input screen across to the keyboard-based one.

You must ensure that you use the TOSHIBA Password Utility to register a User Password before using the Fingerprint boot authentication and its extended function to allow fingerprints to be used to access the computer when it is turned on.

When swiping your finger, please ensure that you do it slowly and at a constant speed. If you find that this does not improve the authentication rate, you should try to adjust the speed at which the finger is swiped.

If there are any changes in the environment or settings related to authorization, you will be required to provide authorization information such as a User Password (and, if applicable, the HDD (Hard Disk

Drive) password).

User's Manual 3-13

User's Manual

Overview about Fingerprint Single Sign-on feature

This is a feature that allows the user to complete the authentication for both the User/BIOS Password (and, if applicable, the HDD (Hard Disk Drive)

Password) and logging onto Windows using only one fingerprint authentication when booting up.

It is necessary to register the User/BIOS Password and Windows Logon

Password before using the Fingerprint boot authentication and this

Fingerprint Single Sign-On Feature. Please use the TOSHIBA Password

Utility to register your User/BIOS Password. If Windows Logon is not the default for your system, see Manual to register your Windows Logon

Password.

Only one fingerprint authentication is required to replace the User/BIOS

Password (and, if applicable, the HDD (Hard Disk Drive) Password) and the Windows Logon Password.

How to Enable Fingerprint boot authentication and Single

Sign-On feature

It is necessary to first enroll your fingerprint with the TOSHIBA Fingerprint

Utility prior to enabling and configuring the boot authentication and Single

Sign-On feature. You should check that your fingerprint is enrolled before configuring the settings.

1.

Logon as Administrator (means a user has administrator privileges).

2.

Click Start -> All Programs -> TOSIHBA -> Utilities -> TOSHIBA

Fingerprint Utility.

3.

Swipe your finger across the fingerprint sensor.

4.

The TOSHIBA Fingerprint Utility main menu is displayed. Click Run

As Administrator in lower left.

5.

User Account Control window is displayed. Click Yes.

6.

Swipe your finger across the fingerprint sensor.

7.

Select Setting in the main menu to open the Setting window, you can

Select Boot authentication check box if you want to use the fingerprint boot authentication feature.

Select Boot authentication and Single sign-on check boxes if you want to use the Single Sign-on feature.

8.

Click Apply.

9.

"Save succeeded!" is displayed. Click OK.

10. Click Close.

11. "Are you sure you want to quit?" is displayed. Click OK. It will be returned to the TOSHIBA Fingerprint Utility main menu.

This modified configuration for fingerprint boot authentication and Single

Sign-on feature becomes effective the next time the system is booted up.

3-14

Optical disc drives

The computer may be installed with an Optical Disc Drive. When the computer is accessing an optical disc, an indicator on the drive glows.

Some models are equipped with an optical disc drive.

Formats

The drives support the following formats.

DVD Super Multi drive Double Layer

The drive supports the following formats: CD-ROM, DVD-ROM, DVD-

Video, CD-DA, CD-Text, Photo CD™ (single/multi-session), CD-ROM

Mode 1/Mode 2, CD-ROM XA Mode 2 (Form1, Form2), Enhanced CD (CD-

EXTRA), Addressing Method 2, DVD-R, DVD-RW, DVD+R, DVD+RW,

DVD-RAM, DVD-R DL (Format1), DVD+R DL.

Blu-ray™ Writer drive

In addition to the above formats, Blu-ray™ Writer drive supports BD-ROM,

BD-ROM DL, BD-R, BD-R DL, BD-RE and BD-RE DL.

Using optical disc drives

The full-size drive provides high-performance execution of disc based programs. You can run either 12 cm (4.72") or 8 cm (3.15") discs without an adaptor.

Use the DVD playback application to view DVD-Video discs.

If you have an Optical disc drive, refer also to the

Writing discs

section for precautions on writing to discs.

To load discs, follow the steps as detailed below:

1.

When the computer’s power is on, press the eject button to open the disc tray slightly.

User's Manual 3-15

2.

Grasp the disc tray gently and pull until it is fully opened.

Figure 3-7 Pressing the eject button and pulling the disc tray open (R830)

1. Disc tray 2. Eject button

1

2

User's Manual 3-16

3.

Lay the disc, label side up, in the disc tray.

Figure 3-8 Inserting a disc (R830)

User's Manual

1

1. Laser lens

When the disc tray is fully opened, the edge of the computer will slightly cover the disc tray. Therefore, you will need to turn the disc at an angle when you place it in the disc tray. After seating the disc, however, make sure it lies flat.

Do not touch the laser lens or any portion of its surrounding casing as this could cause misalignment.

Prevent foreign objects from entering the drive. Check the surface of the disc tray, especially the area behind the front edge of the disc tray, to make sure there are no such objects before closing the drive.

4.

Press gently at the center of the disc until you feel it click into place.

The disc should lie below the top of the spindle, flush with the spindle base.

5.

Push the center of the disc tray to close it. Press gently until it locks into place.

If the disc is not seated properly when the disc tray is closed, the disc might be damaged. Also, the disc tray might not open fully when you press the eject button.

Removing discs

To remove the disc, follow the steps as detailed below:

3-17

Do not press the eject button while the computer is accessing the media drive. Wait for the optical disc drive indicator to go out before you open the disc tray. Also, if the disc is spinning when you open the disc tray, wait for it to stop before you remove it.

1.

To pop the disc tray partially open, press the eject button. Gently pull the disc tray out until it is fully opened.

When the disc tray pops open slightly, wait a moment to make sure the disc has stopped spinning before pulling the disc tray fully open.

2.

The disc extends slightly over the sides of the disc tray so you can grasp it. Gently lift out the disc.

3.

Push the center of the disc tray to close it. Press gently until it locks into place.

How to remove disc when the disc tray will not open

Pressing the eject button will not open the disc tray when the computer power is off. If the power is off, you can open the disc tray by inserting a slender object (about 15 mm) such as a straightened paper clip into the eject hole near the eject button.

Figure 3-9 Manual release with the eject hole (R830)

User's Manual

1

Φ 1.0mm

1. Eject hole

Turn off the power before you use the eject hole. If the disc is spinning when you open the disc tray, the disc could fly off the spindle and cause injury.

3-18

Writable discs

This section describes the types of writable discs. Check the specifications of your drive to see the types of discs it can write. Use TOSHIBA Disc

Creator and Corel Digital Studio to write compact discs.

CDs

CD-R discs can be written only once. The recorded data cannot be erased or changed.

CD-RW discs including multi speed CD-RW discs, high-speed CD-RW discs and ultra-speed CD-RW discs can be recorded more than once.

DVDs

DVD-R, DVD+R, DVD-R DL and DVD+R DL discs can be written only once. The recorded data cannot be erased or changed.

DVD-RW, DVD+RW and DVD-RAM discs can be recorded more than once.

Blu-ray™ discs

BD-R, BD-R DL discs can be written only once. The recorded data cannot be erased or changed.

BD-RE, BD-RE DL discs can be recorded more than once.

Writing discs

The TOSHIBA Disc Creator is provided as writing software with this computer.

Corel Digital Studio can be used to write files in video format. TOSHIBA

Disc Creator can be used to write data.

You can use the DVD Super Multi drive to write data to either CD-R, CD-

RW, DVD-R, DVD-R DL, DVD-RW, DVD+R, DVD+R DL, DVD+RW or

DVD-RAM discs.

You can use the Blu-ray™ Writer drive to write data to either CD-R, CD-

RW, DVD-R, DVD-R DL, DVD-RW, DVD+R, DVD+R DL, DVD+RW, DVD-

RAM, BD-R, BD-R DL, BD-RE or BD-RE DL discs.

When writing information to media using an optical drive, you should always ensure that you connect the AC adaptor to a live power socket. It is possible that, if data is written while powered by the battery pack, the write process may sometimes fail due to low battery power - in these instances data loss may occur.

User's Manual

Important message

Before you write or rewrite to any of the media supported by the Optical

Disc Drive, please read and follow all of the setup and operating

3-19

instructions in this section. If you fail to do so, you may find that the Optical

Disc Drive may not function properly, and you may fail to write or rewrite information successfully - this may cause you to either lose data or incur other damage to the drive or media.

Disclaimer

TOSHIBA does not bear responsibility for the following:

Damage to any disc that may be caused by writing or rewriting with this product.

Any change or loss of the recorded contents of media that may be caused by writing or rewriting with this product, or for any business profit loss or business interruption that may be caused by the change or loss of the recorded contents.

Damage that may be caused by using third party equipment or software.

Given the technological limitations of current optical disc writing drives, you may experience unexpected writing or rewriting errors due to disc quality or problems with hardware devices. In view of this, it is good practice to make two or more copies of important data, in case of any undesired change or loss of the recorded contents.

Before writing or rewriting

Based on TOSHIBA's limited compatibility testing, we suggest the following manufacturers of disc media, however, it must be noted that disc quality can affect writing or rewriting success rates. Please also be aware that in no event does TOSHIBA guarantee the operation, quality or performance of any disc.

CD-R:

TAIYO YUDEN CO., Ltd.

MITSUBISHI KAGAKU MEDIA CO., LTD.

CD-RW: (Multi-Speed, High-Speed and Ultra-Speed)

MITSUBISHI KAGAKU MEDIA CO., LTD.

DVD-R:

DVD Specifications for Recordable Disc for General Version 2.0

TAIYO YUDEN Co.,Ltd. (for 8x and 16x speed media)

MITSUBISHI KAGAKU MEDIA CO., LTD. (for 8x and 16x speed media)

Hitachi Maxell, Ltd. (for 8x and 16x speed media)

DVD-R DL:

MITSUBISHI KAGAKU MEDIA CO., LTD. (for 4x and 8x speed media)

User's Manual 3-20

User's Manual

DVD+R:

MITSUBISHI KAGAKU MEDIA CO., LTD. (for 8x and 16x speed media)

TAIYO YUDEN CO., Ltd. (for 8x and 16x speed media)

DVD+R DL:

MITSUBISHI KAGAKU MEDIA CO., LTD. (for 8x speed media)

DVD-RW:

DVD Specifications for Recordable Disc for Version 1.1 or version

1.2

Victor Company of Japan, Ltd. (JVC) (for 2x, 4x and 6x speed media)

MITSUBISHI KAGAKU MEDIA CO., LTD. (for 2x, 4x and 6x speed media)

DVD+RW:

MITSUBISHI KAGAKU MEDIA CO., LTD. (for 4x and 8x speed media)

DVD-RAM: (DVD Super Multi drive only)

DVD Specifications for DVD-RAM Disc for Version 2.0, Version 2.1 or

Version 2.2

Panasonic Corporation (for 3x and 5x speed media)

Hitachi Maxell, Ltd. (for 3x and 5x speed media)

BD-R:

Panasonic Corporation

BD-R DL:

Panasonic Corporation

BD-RE:

Panasonic Corporation

BD-RE DL:

Panasonic Corporation

Some types and formats of DVD-R DL and DVD+R DL discs may be unreadable.

DISC created in DVD-R DL format4 (Layer Jump Recording) cannot be read.

When writing or rewriting

Please observe the following points while you write or rewrite data to a media:

3-21

Always copy data from the hard disk drive to the optical media - do not use the cut-and-paste function as the original data will be lost if there is a write error.

Do not perform any of the following actions:

Change users in the Operating Systems.

Operate the computer for any other function, including such tasks as using a mouse or Touch Pad, or closing/opening the display panel.

Start a communication application such as a modem.

Apply impact or vibration to the computer.

Install, remove or connect external devices, including such items as an ExpressCard, memory media card, USB device, external monitor or an optical digital device.

Use the audio/video control button to reproduce music or voice.

Open the optical disc drive.

Do not use shut down, log off, Sleep Mode or Hibernation Mode functions while writing or rewriting.

Make sure that the writing/rewriting operation is completed before going into either Sleep Mode or Hibernation Mode (You can remove an optical media on the optical disc drive after writing is completed).

If the media is of poor quality, or is dirty or damaged, writing or rewriting errors may occur.

Set the computer on a level surface and avoid places subject to vibration such as airplanes, trains or cars. In addition, do not use the computer on an unstable surface such as a stand.

Keep mobile phones and other wireless communication devices away from the computer.

TOSHIBA Disc Creator

Please be aware of the following limitations when you use the TOSHIBA

Disc Creator:

DVD Video cannot be created using TOSHIBA Disc Creator.

DVD Audio cannot be created using TOSHIBA Disc Creator.

You cannot use TOSHIBA Disc Creator's "Audio CD" function to record music to DVD-R, DVD-R DL, DVD-RW, DVD+R, DVD+R DL or

DVD+RW media.

Do not use the "Disc Backup" function of TOSHIBA Disc Creator in order to copy DVD Video or DVD-ROM material that has copyright protection.

DVD-RAM discs cannot be backed up using the "Disc Backup" function of TOSHIBA Disc Creator.

You cannot back up CD-ROM, CD-R or CD-RW media to DVD-R,

DVD-R DL or DVD-RW media using the "Disc Backup" function of

TOSHIBA Disc Creator.

User's Manual 3-22

User's Manual

You cannot back up CD-ROM, CD-R or CD-RW media to DVD+R,

DVD+R DL or DVD+RW media using the "Disc Backup" function of

TOSHIBA Disc Creator.

You cannot back up DVD-ROM, DVD Video, DVD-R, DVD-R DL,

DVD-RW, DVD+R, DVD+R DL or DVD+RW to CD-R or CD-RW media using the "Disc Backup" function of TOSHIBA Disc Creator.

TOSHIBA Disc Creator cannot record in packet format.

You might not be able to use the "Disc Backup" function of TOSHIBA

Disc Creator to back up a DVD-R, DVD-R DL, DVD-RW, DVD+R,

DVD+R DL or DVD+RW disc that was made with other software on a different optical media recorder.

If you add data to a DVD-R, DVD-R DL, DVD+R or DVD+R DL disc that you have already recorded to, you might not be able to read the added data under some circumstances. For example, it cannot be read under 16-bit operating systems, such as Windows 98SE and

Windows Me, while in Windows NT4 you will need Service Pack 6 or later, and in Windows 2000, you will need Service Pack 2. In addition to this, some DVD-ROM and DVD-ROM / CD-R/RW drives cannot read this added data regardless of the operating system.

TOSHIBA Disc Creator does not support recording to DVD-RAM discs

- to achieve this you should use Windows Explorer or another similar utility.

When you back up a DVD disc, be sure that the source drive supports recording to DVD-R, DVD-R DL, DVD-RW, DVD+R, DVD+R DL or

DVD+RW media - if this is not the case then the source disc might not be backed up correctly.

When you back up a DVD-R, DVD-R DL, DVD-RW, DVD+R, DVD+R

DL or DVD+RW disc, be sure to use the same type of disc.

You cannot partially delete any data written to a CD-RW, DVD-RW or

DVD+RW disc.

Data Verification

To verify that data has been written or rewritten correctly to a data disc you should follow the steps below before you begin the writing/rewriting process:

1.

Click Start -> All Programs -> TOSHIBA -> CD&DVD Applications -

> Disc Creator to access the TOSHIBA Disc Creator.

2.

Display the setting dialog box by one of the following two steps:

Click the Recording settings button ( ) for writing on the main toolbar in the Data CD/DVD mode.

Select Settings for Each Mode -> Data CD/DVD in the Settings menu.

3.

Mark the Verify Written Data check box.

4.

Select File Open or Full Compare mode.

5.

Click the OK button.

3-23

How to learn more about TOSHIBA Disc Creator

Please refer to the Help files for additional TOSHIBA Disc Creator information.

Using Corel Digital Studio for TOSHIBA

This feature is supported with some models.

How to make a Labelflash DVD

Labelflash features cannot be used in models that do not have an optical disc drive with Labelflash.

In order to determine if the optical disc drive installed in your computer supports Labelflash follow the steps as detailed below:

1. Launch Corel Label@Once:

Click Start -> All Programs -> Corel Digital Studio for TOSHIBA ->

Corel Digital Studio for TOSHIBA -> Create. Click Create disc

label.

2. Click the General tab.

3. Choose optical disc drive for Printer.

If the drive name is displayed in Step 3, your computer's optical disc drive supports Labelflash.

Simplified steps for making a DVD-Video or a Blu-ray Disc™ movie from adding video source:

1.

Insert a Labelflash disc in optical disc drive.

Set PRINTING SIDE for underside.

2.

Click Start -> All Programs -> Corel Digital Studio for TOSHIBA ->

Corel Digital Studio for TOSHIBA -> Create.

3.

Click Create disc label.

How to make a DVD-Video or a Blu-ray Disc™ Movie

Simplified steps for making a DVD-Video or a Blu-ray Disc™ movie from adding video source:

1.

Click Start -> All Programs -> Corel Digital Studio for TOSHIBA ->

Corel Digital Studio for TOSHIBA to launch Corel Digital Studio.

2.

Insert a disc in optical disc drive.

3.

Find a source video and drag it onto Media Tray.

4.

Click Burn -> Video Disc.

5.

Select DVD or Blu-ray in Select disc.

6.

Select DVD-Video/AVCHD or BDMV in Project format.

7.

Input project name and select a style.

User's Manual 3-24

8.

Click the Go to menu editing button.

9.

Click the Burn button.

How to learn more about Corel Digital Studio

Please refer to the Help and Manual files for additional Corel Digital Studio information.

Opening the Corel Digital Studio Manual

Press F1 key when Corel Digital Studio is launched.

Important information for use

Note the following limitations when you write Video DVD or Blu-ray Disc™ movie, file convert or playback files.

Editing digital video

Log in with Administrator rights to use Corel Digital Studio.

Make sure that your computer is running on AC power when using

Corel Digital Studio.

Operate the computer at Full Power. Do not use power-saving features.

While you are editing DVD, you can display preview. However, if another application is running. The preview might not display properly.

Corel Digital Studio cannot edit or play copy protected content.

Do not enter Sleep or Hibernation Mode while using Corel Digital

Studio.

Do not operate Corel Digital Studio immediately after turning on the computer. Please wait until all Disc Drive activity has stopped.

CD recorder, DVD-Audio, Video CD functions are not supported in this version.

Do not run software like a screen saver because it can put a heavy load on the CPU.

Do not support mp3 decode and encode.

DVD-VR format is not supported in this version.

Before recording the video to DVD or Blu-ray Disc™

When you record DVD disc or Blu-ray Disc™, please use only discs recommended by the Drive manufacturer.

Do not set the working drive to a slow device like a USB1.1 hard disk drive or it will fail to write DVD or Blu-ray Disc™.

User's Manual 3-25

Do not perform any of the following actions:

Operate the computer for any other function, including using a mouse or Touch Pad, or closing/opening the display panel.

Bump or cause vibration to the computer.

Use the Mode control button and Audio/Video control button to reproduce music or voice.

Open the optical disc drive.

Install, remove or connect external devices, including the following: memory media card, USB device, external display, optical digital devices.

Please verify your disc after recording important data.

Not support to output VCD and SVCD format.

Force eject disc.

About recorded DVDs and Blu-ray™ discs

Some DVD-ROM drives for personal computers or other DVD players may not be able to read DVD-R/+R/-RW/+RW/-RAM discs.

When playing your recorded DVD on your computer, please use the

TOSHIBA VIDEO PLAYER software application.

When playing your recorded Blu-ray Disc™ on your computer, please use the WinDVD BD for TOSHIBA software application.

If you use an over-used rewritable disc, the full formatting might be locked. Please use a brand new disc.

TOSHIBA VIDEO PLAYER

Please be aware of the following limitations when you use the TOSHIBA

VIDEO PLAYER:

Notes on use

This software can only be used on Windows 7.

TOSHIBA VIDEO PLAYER software is supported for playback of

DVD-Video and DVD-VR.

Frame dropping, audio skipping or out of sync audio and video may occur during playback of some DVD-Video titles.

Close all other applications when using the TOSHIBA VIDEO

PLAYER. Do not open any other applications or carry out any other operations during video playback. Playback may stop or not function properly in some situations.

Unfinalized DVDs created on home DVD recorders may not be playable on the computer.

Use DVD-Video discs with a region code which is either "the same as the factory default setting" (if applicable) or "ALL".

User's Manual 3-26

Do not playback video while watching or recording television programs using other applications. Doing so may cause DVD-Video playback or television program recording errors. In addition, if prescheduled recording starts during DVD-Video playback it may cause DVD-Video playback or television program recording errors. Please view DVD-

Video during times when there is no recording prescheduled.

The resume function cannot be used with some discs on the

TOSHIBA VIDEO PLAYER.

It is recommended the AC adaptor be connected when playing video.

Power saving features may interfere with smooth playback. When playing DVD-Video using battery power, set the Power Options to

"Balance".

The screen saver is disabled during video playback using the

TOSHIBA VIDEO PLAYER. The computer will not automatically go into Hibernation, Sleep, or shut-down mode.

Do not configure the Display automatic power off function to run while the TOSHIBA VIDEO PLAYER is running.

Do not switch to Hibernation or Sleep Mode when running the

TOSHIBA VIDEO PLAYER.

Do not lock the computer using the Windows logo ( ) + L keys or the FN + F1 keys when running the TOSHIBA VIDEO PLAYER.

The TOSHIBA VIDEO PLAYER does not have a parental control function.

In order to protect copyrights, the Windows Print Screen function is disabled when TOSHIBA VIDEO PLAYER is running.

(Print Screen functions are disabled even when running other applications besides TOSHIBA VIDEO PLAYER and when TOSHIBA

VIDEO PLAYER is minimized.) Please close the TOSHIBA VIDEO

PLAYER to use the Print Screen function.

Carry out the installation/uninstallation of the TOSHIBA VIDEO

PLAYER under a user account with administrator rights.

Do not change Windows Users while TOSHIBA VIDEO PLAYER is running.

For some DVD-Video discs, using the control window to change the audio track will also change the subtitle track.

If you see the screen blinking while playing DVD with subtitle on at

Media Player, please use TOSHIBA VIDEO PLAYER or Media Center to play DVD.

Display Devices & Audio

TOSHIBA VIDEO PLAYER will only run when "Colors" is set to "True

Color (32 bit)". Click Start -> Control Panel -> Appearance and

Personalization -> Display -> Adjust resolution, click "Advanced settings", select "Monitor" tab, set "colors" to "True color (32 bit)".

User's Manual 3-27

If the DVD-Video image is not displayed on an external display or television, stop the TOSHIBA VIDEO PLAYER, and change the screen resolution. To change the screen resolution, click Start ->

Control Panel -> Appearance and Personalization -> Display ->

Adjust resolution. However, video cannot be output to some external displays and televisions due to output or playback conditions.

When viewing DVD-Video on an external display or TV, change the display device before playing. DVD-Video cannot be displayed simultaneously (in clone mode) on both the computer's display panel and an external display.

Do not change the screen resolution while running the TOSHIBA

VIDEO PLAYER.

Do not change the display device while running the TOSHIBA VIDEO

PLAYER.

Starting TOSHIBA VIDEO PLAYER

Use the following procedure to start TOSHIBA VIDEO PLAYER.

1.

Insert a DVD-Video in the optical disc drive while Windows ® 7 is running.

When a DVD-Video disc is set in the DVD drive (for models with DVD drive), if the application selection screen appears, select Play DVD

movie, (using TOSHIBA VIDEO PLAYER) to launch the TOSHIBA

VIDEO PLAYER.

2.

Select Start -> All Programs -> TOSHIBA VIDEO PLAYER ->

TOSHIBA VIDEO PLAYER to start TOSHIBA VIDEO PLAYER.

Operating TOSHIBA VIDEO PLAYER

Notes on Using TOSHIBA VIDEO PLAYER.

Screen display and available features may vary amongst DVD-Videos and scenes.

If the menu is opened in the Display Area using the Control window's

Top Menu or Menu buttons, touch pad and mouse menu operations may not be able to be used.

Open TOSHIBA VIDEO PLAYER HELP

TOSHIBA VIDEO PLAYER features and instructions are also explained in detail in "TOSHIBA VIDEO PLAYER HELP". Use the following procedure to open "TOSHIBA VIDEO PLAYER HELP".

Click the "Help" button ( ) in the Display Area.

Using WinDVD BD for TOSHIBA

Please be aware of the following limitations when you use WinDVD BD for

TOSHIBA:

User's Manual 3-28

Notes on use

“WinDVD BD for TOSHIBA” is for Blu-ray Disc™ playback only. DVD playback is not supported. Please use “TOSHIBA VIDEO PLAYER” for

DVD playback.

Playback of high bit rate content may cause frame dropping, audio skipping or decrease in computer performance.

Close all other applications before playing back Blu-ray Disc™. Do not open any other applications or carry out any other operations during

Blu-ray Disc™ playback.

Do not switch to Hibernation or Sleep Mode when running the

“WinDVD BD for TOSHIBA”.

Because Blu-ray Disc™ playback operates according to programs built into the content, operation methods, operation screens, sound effects, icons and other features may vary from disc to disc. For more information on these items refer to instructions included with content or contact the content manufacturers directly.

Make sure to connect the computer's AC adapter when playing a Bluray Disc™.

“WinDVD BD for TOSHIBA” supports AACS (Advanced Access

Control System) copy protection technology. Renewal of the AACS key integrated into this product is required for uninterrupted enjoyment of Blu-ray Disc™. An Internet connection is required for renewal.

AACS key renewal is provided free of charge for 5 years after the purchase of this product, however renewal beyond 5 years is subject to conditions specified by the software provider, Corel Corporation.

Do not playback Blu-ray Disc™ while recording television programs using “Windows Media Center” “My TV” or other applications. Doing so may cause Blu-ray Disc™ playback or television program recording errors. In addition, if pre-scheduled recording starts during Blu-ray

Disc™ Video playback it may cause Blu-ray Disc™ Video playback or television program recording errors. Please view Blu-ray Disc™ Video during times when there is no recording prescheduled.

While playing a BD-J title, keyboard shortcut is ineffective.

Resume play function cannot be used with some discs on “WinDVD

BD for TOSHIBA”.

The interactive function on Blu-ray™ Discs may not work depending on the contents or network situation.

Blu-ray™ drives and their associated media are manufactured according to the specifications of three marketing regions. Region codes can be set from WinDVD BD ([Region] tab in [Setup] dialogue).

When you purchase Blu-ray™ Video, make sure it matches your drive, otherwise it will not play properly.

To playback video on an external display or TV using “WinDVD BD for

TOSHIBA”, use output devices like external displays or TV that have

HDCP supported HDMI port. The video cannot be displayed on an external display or TV connected to the RGB connector.

User's Manual 3-29

The Blu-ray Disc™ movie can be played only on internal LCD displays or external devices connected via an HDMI output. In Clone mode

(Dual View), WinDVD plays on a display which set to as the Primary display and shows black screen on the other displays.

This product does not play HD DVD discs. Blu-ray™ discs with high definition content are required for HD viewing.

Starting WinDVD BD for TOSHIBA

Use the following procedure to start “WinDVD BD for TOSHIBA”.

1.

When a Blu-ray Disc™ is set in the Blu-ray™ drive, WinDVD BD for

TOSHIBA starts automatically.

2.

Select Start -> All Programs -> Corel -> Corel WinDVD BD to start

"WinDVD BD for TOSHIBA".

Operating WinDVD BD for TOSHIBA

Notes on Using “WinDVD BD for TOSHIBA”.

Screen display and available features may vary amongst Blu-ray™

Videos and scenes.

If the menu is opened in the Display Area using the Control window's

Top Menu or Menu buttons, Touch Pad and mouse menu operations may not be able to be used.

Open WinDVD BD for TOSHIBA HELP

WinDVD BD for TOSHIBA features and instructions are also explained in detail in “WinDVD Help”. Use the following procedure to open “WinDVD

Help”.

Click the “Corel Guide” button ) in the Display Area.

Wireless communications

The computer’s wireless communication function supports some wireless communication devices.

Only some models are equipped with both Wireless LAN and Bluetooth functions.

Do not use the Wireless LAN (Wi-Fi) or Bluetooth functionalities near a microwave oven or in areas subject to radio interference or magnetic fields. Interference from a microwave oven or other source can disrupt

Wi-Fi or Bluetooth operation.

Turn all wireless functionalities off when near a person who may have a cardiac pacemaker implant or other medical electric device. Radio waves may affect pacemaker or medical device operation, possibly resulting in serious injury. Follow the instruction of your medical device when using any wireless functionality.

User's Manual 3-30

Always turn off wireless functionality if the computer is near automatic control equipment or appliances such as automatic doors or fire detectors. Radio waves can cause malfunction of such equipment, possibly resulting in serious injury.

It may not be possible to make a network connection to a specified network name using the ad hoc network function. If this occurs, the new network(*) will have to be configured for all computers connected to the same network in order to re-enable network connections.

* Please be sure to use new network name.

Wireless LAN

The Wireless LAN is compatible with other LAN systems based on Direct

Sequence Spread Spectrum / Orthogonal Frequency Division Multiplexing radio technology that complies with the IEEE802.11 Wireless LAN standard.

Frequency Channel Selection of 5GHz for IEEE 802.11a or/and

IEEE802.11n

Frequency Channel Selection of 2.4GHz for IEEE 802.11b/g or/and

IEEE802.11n

Roaming over multiple channels

Card power management

Wired Equivalent Privacy (WEP) data encryption based on an 128-bit encryption algorithm

Wi-Fi Protected Access™ (WPA™)

The transmission speed over the wireless LAN, and the distance over which the wireless LAN can reach, may vary depending on surrounding electromagnetic environment, obstacles, access point design and configuration, client design and software/hardware configurations. The transmission rate described is the theoretical maximum speed as specified under the appropriate standard - the actual transmission speed will be lower than the theoretical maximum speed.

Setting

1.

Please make sure that the Wireless Communication function is on.

2.

Click Start -> Control Panel -> Network and Internet -> Network

and Sharing Center.

3.

Click Set up a new connection or network.

4.

Follow the wizard. You will need the name of the wireless network together with security settings. Consult the documentation accompanied with your router or ask your wireless network administrator for the settings.

User's Manual 3-31

User's Manual

Security

TOSHIBA strongly recommend that you enable encryption functionality, otherwise your computer will be open to illegal access by an outsider using a wireless connection. If this occurs, the outsider may illegally access your system, eavesdrop, or cause the loss or destruction of stored data.

TOSHIBA is not liable for the loss of data due to eavesdropping or illegal access through the wireless LAN and the damage thereof.

Card Specifications

Form Factor

Compatibility

PCI Express Mini Card

IEEE 802.11 Standard for Wireless LANs

Wi-Fi (Wireless Fidelity) certified by the Wi-

Fi Alliance. The "Wi-Fi CERTIFIED" logo is a certification mark of the Wi-Fi Alliance.

Microsoft Windows Networking Network Operating

System

Media Access Protocol

CSMA/CA (Collision Avoidance) with

Acknowledgment (ACK)

Radio Characteristics

Radio Characteristics of Wireless LAN module may vary according to:

Country/region where the product was purchased

Type of product

Wireless communication is often subject to local radio regulations.

Although Wireless LAN wireless networking products have been designed for operation in the license-free 2.4GHz and 5GHz band, local radio regulations may impose a number of limitations to the use of wireless communication equipment.

Radio Frequency Band 5GHz (5150-5850 MHz) (Revision a and n)

Band 2.4GHz (2400-2483.5 MHz) (Revision b/g and n)

The range of the wireless signal is related to the transmit rate of the wireless communication. Communications at lower transmit range may travel larger distances.

The range of your wireless devices can be affected when the antennas are placed near metal surfaces and solid high-density materials.

Range is also impacted due to "obstacles" in the signal path of the radio that may either absorb or reflect the radio signal.

3-32

Bluetooth wireless technology

Some computers in this series have Bluetooth wireless communication function which eliminates the need for cables between electronic devices such as computers, printers and mobile phones. When it is enabled,

Bluetooth provides the wireless personal area network environment which is safe and trustworthy, that is quick and easy.

You cannot use the computer's built-in Bluetooth functions and an external

Bluetooth adaptor simultaneously. For reference, Bluetooth wireless technology has the following features:

Worldwide operation

The Bluetooth radio transmitter and receiver operate in the 2.4GHz band, which is license-free and compatible with radio systems in most countries in the world.

Radio links

You can easily establish links between two or more devices, with these links being maintained even if the devices are not within a line-of-sight of each other.

Security

Two advanced security mechanisms ensure a high level of security:

Authentication prevents access to critical data and makes it impossible to falsify the origin of a message.

Encryption prevents eavesdropping and maintains link privacy.

Bluetooth Stack for Windows by TOSHIBA

Please note that this software is specifically designed for the following operating systems:

Windows 7

Information regarding the use of this software with these operating systems is listed below, with further details being contained with the electronic help files supplied with the software.

This Bluetooth Stack is based on the Bluetooth Version 1.1/1.2/2.0+EDR/

2.1+EDR/3.0/3.0+HS specification, depending on the model you purchased. However, TOSHIBA cannot confirm the compatibility between any computing products and/or other electronic devices that use Bluetooth, other than TOSHIBA notebook computers.

User's Manual 3-33

Release Notes related to the Bluetooth Stack for Windows by TOSHIBA

1.

Fax application software: Please be aware that there is some fax application software that you cannot use on this Bluetooth Stack.

2.

Multi-user considerations: The use of Bluetooth is not supported in a multi-user environment. This means that, when you use Bluetooth, other users that are logged into the same computer will not be able to use this type of functionality.

Product Support:

The latest information regarding operating system support, language support or available upgrades can be found on our web site http:// www.toshiba-europe.com/computers/tnt/bluetooth.htm in Europe or www.pcsupport.toshiba.com in the United States.

LAN

The computer has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T), Fast Ethernet LAN (100 megabits per second,

100BASE-TX) or Gigabit Ethernet LAN (1000 megabits per second,

1000BASE-T).

This section describes how to connect/disconnect to a LAN.

Do not install or remove a memory module while Wake-up on LAN is enabled.

The Wake-up on LAN function consumes power even when the system is off. Leave the AC adaptor connected while using this feature.

The Link speed (10/100/1000 megabits per second) changes automatically depending on the network conditions (connected device, cable or noise and so on).

LAN cable types

The computer must be configured properly before connecting to a LAN.

Logging onto a LAN using the computer’s default settings could cause a malfunction in LAN operation. Check with your LAN administrator regarding set-up procedures.

If you are using Gigabit Ethernet LAN (1000 megabits per second,

1000BASE-T), be sure to connect with a CAT5e cable or higher. You cannot use a CAT3 or CAT5 cable.

User's Manual 3-34

If you are using Fast Ethernet LAN (100 megabits per second, 100BASE-

TX), be sure to connect with a CAT5 cable or higher. You cannot use a

CAT3 cable.

If you are using Ethernet LAN (10 megabits per second, 10BASE-T), you can connect with a CAT3 or higher cable.

Connecting the LAN cable

To connect the LAN cable, follow the steps as detailed below:

Connect the AC adaptor before connecting the LAN cable. The AC adaptor must remain connected during LAN use. If you disconnect the

AC Adaptor while the computer is accessing a LAN, the system may hang up.

Do not connect any other cable to the LAN jack except the LAN cable.

Otherwise, malfunctions or damage may occur.

Do not connect any power supplying device to the LAN cable that is connected to the LAN jack. Otherwise, malfunctions or damage may occur.

1.

Turn off the power to all external devices connected to the computer.

2.

Plug one end of the cable into the LAN jack. Press gently until you hear the latch click into place.

Figure 3-10 Connecting the LAN cable (R830)

2

1

1. LAN jack 2. LAN cable

3.

Plug the other end of the cable into a LAN hub connector or router.

Check with your LAN administrator and hardware or software vendor before using or configuring a network connection.

Optional devices

Optional devices can expand the computer's capabilities and its versatility.

This section describes the connection or installation of the following devices:

Cards/memory

ExpressCard (ExpressCard/34 or ExpressCard/54)

User's Manual 3-35

Smart Card

Memory media slot

Additional memory module

Peripheral devices

External monitor

HDMI

DisplayPort eSATA devices

TOSHIBA Hi-Speed Port Replicator II

Other

Security lock

Optional TOSHIBA accessories

ExpressCard

Some models are equipped with a single ExpressCard slot into which any

ExpressCard device that meets industry standards, either manufactured by

TOSHIBA or another vendor, can be installed. The slot supports hot plug connection and utilizes the PCI Express interface that supports the reading and writing of data at a theoretical maximum rate of 2.5Gbps.

Inserting an ExpressCard

The Windows hot-install feature allows you to insert ExpressCards while the computer is turned on.

Do not insert an ExpressCard while the computer is in Sleep Mode or

Hibernation Mode as you may find that some cards do not work properly.

To insert an ExpressCard, follow the steps as detailed below:

1.

Press the Dummy card in order to eject the Dummy card partially out of the computer.

2.

Grasp the Dummy card and draw it.

3.

Insert the ExpressCard into the ExpressCard slot on the hand side of the computer.

User's Manual 3-36

4.

Press the ExpressCard gently to ensure a firm connection is made.

Figure 3-11 Inserting the ExpressCard (R830)

1 2

1. ExpressCard slot 2. ExpressCard

5.

After inserting the ExpressCard you should refer to its documentation and also check the configuration in Windows in order to ensure that it is correct.

Removing an ExpressCard

To remove an ExpressCard, follow the steps as detailed below.

1.

Open the Safely Remove Hardware and Eject Media icon on the

Windows Taskbar.

2.

Point to ExpressCard and click the left Touch Pad control button.

3.

Press the ExpressCard in order to eject the ExpressCard partially out of the computer.

4.

Grasp the ExpressCard and remove it.

5.

Insert the Dummy card into the ExpressCard slot.

When you do not use an ExpressCard, please be sure to insert a Dummy card.

Smart Card

A Smart Card is a credit card sized plastic card. An extremely thin integrated circuit (IC chip) is embedded into the card on which information can be recorded. These cards can be used for a wide variety of applications including telephone related and electronic monetary payments.

This section contains information on the proper use of the Smart Card slot, and it is strongly recommended that you read it before operating the computer.

Some models are equipped with a Smart Card slot.

Your computer supports ISO7816-3 asynchronous cards (support protocols are T=0 and T=1) with a working voltage of 5V.

User's Manual 3-37

Inserting a Smart Card

The Smart Card slot is located on the side of the computer. The Windows hot-install feature allows you to insert a Smart Card while the computer is turned on.

To install a Smart Card, follow the steps as detailed below:

1.

Insert the Smart Card into the Smart Card slot with the metal connectors facing up.

2.

Press the Smart Card gently to ensure a firm connection is made. The computer will identify the Smart Card and display an icon in the

Windows Taskbar.

When inserting a Smart Card into the Smart Card slot, make sure to confirm that the card is oriented correctly before inserting.

Insert the Smart Card until it reaches the end of the Smart Card slot.

There will be about 2cm of the Smart Card sticking out of the Smart

Card slot. Do not attempt to insert it further.

Always remove the Smart Card from the Smart Card slot before moving the computer.

Remove the Smart Card after use.

Failure to follow these instructions may result in damage to the computer and/or damage to the Smart Card.

3.

After inserting the Smart Card, you should refer to its documentation and also check the configuration in Windows in order to ensure that it is correct.

Removing a Smart Card

To remove a Smart Card, follow the steps as detailed below:

1.

Open the Safely Remove Hardware and Eject Media icon on the

Windows Taskbar.

Before removing the Smart Card, confirm that the Smart Card is not working with any program or system.

Be careful not to bend the Smart Card while removing it from the computer.

2.

Point to Smart Card and click the left Touch Pad control button.

3.

Grasp the Smart Card and remove it.

Memory media slot

The computer is equipped with a memory media slot that can accommodate some kinds of memory media with various memory capacities so that you can easily transfer data from devices, such as digital cameras and Personal Digital Assistants.

User's Manual 3-38

Keep foreign objects out of the memory media slot. Never allow metal objects, such as screws, staples and paper clips, to enter the computer or

Keyboard. Foreign metal objects can create a short circuit, which can cause computer damage and fire, possibly resulting in serious injury.

Please note that an adaptor is required to use miniSD/microSD Card,

Memory Stick Duo, Memory Stick PRO Duo and Memory Stick Micro.

Please note that not all memory media have been tested and verified to work correctly. Therefore, it is not possible to guarantee that all memory media will operate properly.

The slot for some models does not support Magic Gate functions.

Figure 3-12 Examples of memory media

Secure Digital (SD)

Card

microSD card adaptor and microSD card

MultiMediaCard

(MMC)

Memory Stick xD picture card

Memory media

This section provides the important safety precautions in order to handle your memory media.

Points to note about the memory media card

SD/SDHC/SDXC memory cards comply with SDMI (Secure Digital Music

Initiative), which is a technology adopted to prevent unlawful copy or playback of digital music. For this reason, you cannot copy or playback protected material on another computer or other device, and you may not reproduce any copyrighted material except for your personal enjoyment.

Below is a simple explanation for distinguishing SD memory cards from

SDHC memory cards and SDXC memory cards.

SD, SDHC and SDXC memory cards appear the same externally.

However, the logo on memory cards is different, so pay careful attention to the logo when purchasing.

User's Manual 3-39

The SD memory card logo is ( ).

The SDHC memory card logo is ( ).

The SDXC memory card logo is (

TM

).

The maximum capacity of SD memory cards is 2GB. The maximum capacity of SDHC memory cards is 32GB.

Card Type

SD

SDHC

SDXC

Capacities

8MB, 16MB, 32MB, 64MB, 128MB, 256MB,

512MB, 1GB, 2GB

4GB, 8GB, 16GB, 32GB

64GB

Memory media format

New media cards are formatted according to specific standards. If you wish to reformat a media card, be sure to do so with a device that uses media cards.

Formatting an memory media card

Memory media cards are sold already formatted in conformity to specific standards. If you reformat an memory card, be sure to reformat it with a device such as digital camera or digital audio player that uses the memory cards, not with the format command provided within Windows.

Should you need to format all areas of the memory card, including the protected area, you will need to obtain an appropriate application that applies the copy protection system.

Media care

Observe the following precautions when handling the card.

Card care

Do not twist or bend cards.

Do not expose cards to liquids or store in humid areas or lay media close to containers of liquid.

Do not touch the metal part of a card or expose it to liquids or let it get dirty.

After using card, return it to its case.

The card is designed so that it can be inserted only one way. Do not try to force the card into the slot.

Do not leave a card partially inserted in the slot. Press the card until you hear it click into place.

User's Manual 3-40

Memory card care

Set the write-protect switch to the lock position, if you do not want to record data.

Memory cards have a limited lifespan, so it is important to backup important data.

Do not write to a card if the battery power is low. Low power could affect writing accuracy.

Do not remove a card while read/write is in progress.

For more details on using memory cards, see manuals accompanying the cards.

About the write-protect

The memory media cards have a function for protect.

SD Card (SD memory card, SDHC memory card and SDXC memory card)

Memory Stick (Memory Stick, Memory Stick PRO, Memory Stick Duo,

Memory Stick PRO Duo, Memory Stick Micro)

Set the write-protect switch to the lock position, if you do not want to record data.

Inserting a memory media

The following instructions apply to all types of supported media devices. To insert a memory media, follow the steps as detailed below:

1.

Turn the memory media so that the contacts (metal areas) are face down.

2.

Insert the memory media into the memory media slot on the side of the computer.

3.

Press the memory media gently to ensure a firm connection is made.

Figure 3-13 Inserting a memory media (R830)

User's Manual

1

2

1. Memory media slot 2. Memory media

3-41

Make sure memory media is oriented properly before you insert it. If you insert the media in wrong direction, you may not be able to remove it.

When inserting memory media, do not touch the metal contacts. You could expose the storage area to static electricity, which can destroy data.

Do not turn the computer off or switch to Sleep Mode or Hibernation

Mode while files are being copied - doing so may cause data to be lost.

Removing a memory media

The following instructions apply to all types of supported media devices. To remove a memory media, follow the steps as detailed below:

1.

Open the Safely Remove Hardware and Eject Media icon on the

Windows Taskbar.

2.

Point to memory media and click the left Touch Pad control button.

3.

Press the memory media to partially extend it out of the computer.

4.

Grasp the media and remove it.

Make sure the Memory Media slot indicator is out before you remove the memory media or turn off the computer’s power. If you remove the memory media or turn off the power while the computer is accessing the memory media, you may lose data or damage the media.

Do not remove the memory media while the computer is in Sleep or

Hibernation Mode. The computer could become unstable or data in the memory media could be lost.

Do not remove only the Memory Stick Duo/Memory Stick PRO Duo/

Memory Stick Micro/miniSD/microSD Card while leaving the adaptor in the memory media slot.

Additional memory module

You can install additional memory into the computer in order to increase the amount of system memory that is available. This section describes how to install and remove optional memory modules.

You should place a mat beneath the computer in order to prevent the computer's lid from becoming scratched or damaged when you are installing/replacing the memory module. In this instance you should avoid mats that are made of materials that hold or generate static electricity.

When installing or removing a memory module, you must ensure that you do not touch any other internal areas of the computer.

User's Manual 3-42

Insert the two memory modules into Slot A and Slot B respectively.

The computer will operate in dual channel mode. You can access the inserted memory modules efficiently in dual channel.

Use only memory modules approved by TOSHIBA.

Do not try to install or remove a memory module under the following conditions.

a. The computer is turned on.

b. The computer was shut down in either Sleep or Hibernation Mode.

c. Wake-up on LAN is enabled.

d. The wireless communication function is on.

e. Sleep and Charge function is enabled.

Be careful not to let screws or other foreign matter fall into the computer. It could cause malfunction or electric shock.

Additional memory module is a precision electronic component that may be fatally damaged by static electricity. Since the human body can carry static electricity, it is important that you discharge yourself before touching or installing any additional memory modules. To discharge your body’s static electricity, simply touch any metal close to you with bare hands.

Use a point size 1 Phillips screwdriver for R850/R840 and point size 0

Phillips screwdriver for R830 to remove and fasten the screws - the use of an incorrect screwdriver can damage the screw heads.

Installing a memory module

To install a memory module, follow the steps as detailed below:

1.

Shut down the computer - make sure the Power indicator is off (refer to the

Turning off the power

section in Chapter 1, Getting Started if required).

2.

Remove the AC adaptor and all cables and peripherals connected to the computer.

3.

Close the display panel.

4.

Turn the computer upside down and remove the battery pack (refer to

Replacing the battery pack section in Chapter 5, Power and Power-Up

Modes, if required).

5.

Loosen the screw(s) securing the memory module cover in place please note that the screw(s) are attached to the cover in order to prevent them from being lost.

User's Manual 3-43

6.

Slide your fingernail or a thin object under the cover and lift it off.

Figure 3-14 Removing the memory module cover (R830)

1

2

1. Screws 2. Memory module cover

User's Manual 3-44

7.

Align the notch of the memory module with that of the memory slot and gently insert the module into the slot at about a 30 degree angle before holding it down until the latches on either side snap into place.

Figure 3-15 Seating the memory module (R830)

1

2

3

User's Manual

1. Notch

2. Slot B

3. Slot A

Never allow metal objects, such as screws, staples and paper clips, to enter the computer. Foreign metal objects can create a short circuit, which can cause computer damage and fire, possibly resulting in serious injury.

Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems.

The slot A is reserved for the first memory module. Use the slot B for expanded memory. If only one module is installed, use the slot A.

Align the grooves along the edges of the memory module with the locking tabs on the connector and insert the module into the connector firmly - if you find it difficult to install the memory module, gently prise the locking tabs outwards using the tip of your finger.

Please also ensure that you hold the memory module along its left and right hand edges - the edges with the grooves in.

3-45

8.

Seat the memory module cover in place and secure it with the screw(s).

Take care to ensure that the memory module cover is firmly closed.

Figure 3-16 Seating the memory module cover (R830)

2

1

1. Memory module cover 2. Screws

9.

Install the battery pack - refer to

Replacing the battery pack section in

Chapter 5, Power and Power-Up Modes, if required.

10. Turn your computer over.

11. Turn the computer on and make sure the added memory is recognized

- to confirmed it, Start -> Control Panel -> System and Security ->

System icon.

Removing a memory module

To remove the memory module, follow the steps as detailed below:

1.

Shut down the computer - make sure the Power indicator is off (refer to the

Turning off the power

section in Chapter 1, Getting Started if required).

2.

Remove the AC adaptor and all cables and peripherals connected to the computer.

3.

Close the display panel.

4.

Turn the computer upside down and remove the battery pack.

5.

Loosen the screw(s) securing the memory module cover in place please note that the screws are attached to the cover in order to prevent them from being lost.

6.

Slide your fingernail or a thin object under the cover and lift it off.

7.

Push the latches away from the module in order to release it - a spring will force one end of the module up at an angle.

User's Manual 3-46

8.

Grasp the module by its edges and remove it from the computer.

If you use the computer for a long time, the memory modules and the circuits locating close to the memory modules will become hot. In this case, let them cool to room temperature before you replace them. Or you will get burnt if you touch any of them.

Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems.

Figure 3-17 Removing the memory module (R830)

1

1

1. Latches

9.

Seat the memory module cover in place and secure it with the screw(s).

Take care to ensure that the memory module cover is firmly closed.

10. Install the battery pack.

11. Turn your computer over.

External monitor

An external analog monitor can be connected to the External RGB monitor port on the computer. To connect a monitor, follow the steps as detailed below:

Connecting the monitor cable

1.

Connect the monitor cable to the External RGB monitor port.

User's Manual 3-47

Figure 3-18 Connecting the monitor cable to the External RGB monitor port

(R830)

1

2

1. External RGB monitor port 2. Monitor cable

There are no fastening screws for an external monitor cable on this computer's External RGB monitor port. However, external monitor cables which have connectors with fastening screws can still be used.

2.

Turn the external monitor's power on.

When you turn on the power, the computer will automatically recognize the monitor and determine whether it is a color or monochrome device. In the event that you find that there are issues getting an image displayed on the correct monitor, you should consider using the FN + F5 hot key to change the display settings (if you then disconnect the external monitor before you turn the computer's power off, be sure to press FN + F5 hot key again to switch to the internal display).

Please refer to the

The Keyboard

section for further details on using hot keys to change the display setting.

Do not disconnect the external monitor while in Sleep or Hibernation Mode.

Turn off the computer before disconnecting the external monitor.

When displaying desktop at external analog monitor, desktop is sometimes displayed on the center of the monitor with black bars around desktop (with small size).

At that time, please read the manual of the monitor and set the display mode which is supporting at the monitor. Then it will be displayed with suitable size with correct aspect ratio.

HDMI

Some models are equipped with an HDMI out port.

An HDMI monitor can be connected to the HDMI out port on the computer.

To connect monitor, follow the steps as detailed below:

User's Manual 3-48

As the port operation of all HDMI (High-Definition Multimedia Interface) monitors have not been confirmed, some HDMI monitors may not function properly.

Connecting the HDMI out port

1.

Plug one end of the HDMI cable into the HDMI in port of the HDMI device.

2.

Plug the other end of the HDMI cable into the HDMI out port on your computer.

Figure 3-19 Connecting the HDMI out port (R830)

User's Manual

1

2

1. HDMI out port 2. HDMI cable

Please connect or disconnect an HDMI device to or from the computer under the following conditions:

The computer is turned on.

The computer is completely turned off.

Do not do so when the computer is in Sleep Mode or Hibernation Mode.

When you connect a television or external monitor to the HDMI port, the display output device is set to HDMI.

When you unplug the HDMI cable and re-plug it, please wait at least 5 seconds before you re-plug the HDMI cable again.

3-49

When you change the display output device by hot key like FN + F5, the playback device may not switch automatically. In this case, in order to set the playback device to the same device as the display output device, please adjust the playback device manually by the following steps:

1.

Click Start -> Control Panel -> Hardware and Sound -> Sound.

2.

In the Playback tab, select the playback device which you want to switch to.

3.

To use the internal speakers on your computer, select Speakers.

To use the television or the external monitor that you have connected to the computer, select a different playback device.

4.

Click the Set Default button.

5.

Click OK to close the Sound dialog.

Settings for display video on HDMI

To view video on the HDMI device, be sure to configure the following settings otherwise you may find that nothing is displayed.

Be sure to use the FN + F5 HotKey to select the display device before starting to play video. Do not change the display device while playing video.

Do not change the display device under the following conditions.

While data is being read or written.

While communication is being carried out.

Select HD Format

To select the display mode, follow the steps as detailed below:

1.

Click Start and click Control Panel.

2.

Click Appearance and Personalization.

3.

Click Display.

4.

Click Change display settings.

5.

Click Advanced settings.

6.

Click List All Modes.

7.

Select one of the mode at List All Modes.

DisplayPort

Some models are equipped with a DisplayPort. This port enables you to connect an external monitor.

User's Manual 3-50

Connecting the DisplayPort

1.

Plug one end of the DisplayPort cable into the DisplayPort on your external monitor.

2.

Turn on the external monitor.

3.

Plug the other end of the DisplayPort cable into the DisplayPort on your computer.

As the port operation of all external monitors have not been confirmed, some monitors may not function properly.

When you change the display output device by hot key like FN + F5, the playback device may not switch automatically. In this case, in order to set the playback device to the same device as the display output device, please adjust the playback device manually by the following steps:

1.

Click Start -> Control Panel -> Hardware and Sound -> Sound.

2.

In the Playback tab, select the playback device which you want to switch to.

3.

To use the internal speakers on your computer, select Speakers.

To use the television or the external monitor that you have connected to the computer, select a different playback device.

4.

Click the Set Default button.

5.

Click OK to close the Sound dialog.

eSATA (External Serial ATA) devices

An device corresponding to eSATA function can be connected to the eSATA/USB combo port on the computer.

Connecting the eSATA device

To connect an eSATA device, follow the steps as detailed below:

1.

Connect an eSATA cable to the eSATA/USB combo port.

Make sure the connector is properly aligned with the socket.

Do not try to force the connection, doing so can damage the connecting pins.

User's Manual 3-51

Figure 3-20 Connecting an eSATA cable to the eSATA/USB combo port (R830)

2

1

1. eSATA/USB combo port 2. eSATA cable

A connected eSATA device may not be recognized if it is connected to the computer's eSATA/USB combo port while the computer is in Sleep

Mode or Hibernation Mode. If this occurs, disconnect the eSATA device and then reconnect the device while the computer is turned on.

If you connect an eSATA device after the computer has already been turned on, it will take about ten seconds for it to be recognized by the computer. Do not attempt to disconnect and reconnect the drive before this period has elapsed.

Disconnecting an eSATA device

When you have finished using an eSATA device, you can follow the procedures below in order to disconnect it:

1.

Wait for the indicator light of an eSATA device to go out to make sure all activity has stopped.

2.

Click the Safely Remove Hardware and Eject Media icon on the

Windows Taskbar.

3.

Click an eSATA device that you want to remove.

4.

Carefully pull an eSATA device's eSATA/USB combo connector out from within the computer's eSATA/USB combo port.

If you disconnect an eSATA device or turn off the power while the computer is accessing the drive you may lose data or damage an eSATA device or the drive.

TOSHIBA Hi-Speed Port Replicator II

In addition to the ports available on the computer, the TOSHIBA Hi-Speed

Port Replicator II also provides several kinds of ports.

User's Manual 3-52

The TOSHIBA Hi-Speed Port Replicator II connects directly to the docking interface on the underside of the computer. The AC adaptor connects the

TOSHIBA Hi-Speed Port Replicator II to a power source.

You must connect the AC adaptor before you connect to a TOSHIBA

Hi-Speed Port Replicator II.

When a TOSHIBA Hi-Speed Port Replicator II is connected to the computer, you can not use the following computer’s ports: LAN jack,

DC IN 19V jack and External RGB monitor port.

When connecting an AC Adaptor to the TOSHIBA Hi-Speed Port

Replicator II, use only the AC Adaptor included with TOSHIBA Hi-

Speed Port Replicator II. Do not use the computer’s AC Adaptor.

When the replicator is docked, booting from USB 3.0 ports may be not available. To check whether your computer supports booting from

USB 3.0, please contact TOSHIBA support for assistance.

Refer to the TOSHIBA Hi-Speed Port Replicator II User's Manual for more details.

Security lock

A security locks enable you to anchor your computer a desk or other heavy object in order to help prevent unauthorized removal or theft. The computer has a security lock slot on its right side into which you can attach one end of the security cable, while the other end attaches to a desk or similar object. The methods used for attaching security cables differ from product to product. Please refer to the instructions for the product you are using for more information.

Connecting the security lock

In order to connect a security cable to the computer, follow the steps as detailed below:

1.

Turn the computer so its right side faces you.

2.

Align the security cable with the lock slot and secure it in place.

Figure 3-21 Security lock (R830)

1

User's Manual

1. Security lock slot

3-53

Optional TOSHIBA Accessories

You are able to add a number of options and accessories in order to make your computer even more powerful and convenient to use. For reference, the following list details some of the items that are available from your reseller or TOSHIBA dealer:

Memory Kit 1 GB, 2 GB or 4GB memory modules

(DDR3-1333) can easily be installed in the computer.

The available option memory depends on

TOSHIBA authorization.

Universal AC Adaptor If you frequently use your computer at more than one site, it may be convenient to purchase an additional AC adaptor to be kept at each site in order to remove the need to always carry the adaptor with you.

Battery Pack An additional battery pack can be purchased for use as either a spare or replacement. Please refer to Chapter 5,

Power and Power-Up Modes

for further information.

TOSHIBA Hi-Speed

Port Replicator II

The TOSHIBA Hi-Speed Port Replicator II provides several kinds of ports.

Please refer to the TOSHIBA Hi-Speed Port

Replicator II User's manual for more details.

Sound System

This section describes some of the audio control functions.

Volume Mixer

The Volume Mixer utility lets you control the audio volume for playback of devices and applications under Windows.

To launch the Volume Mixer utility, right click on the speaker icon on the Taskbar, and select Open Volume Mixer from the sub menu.

To adjust the volume level of speakers or headphones, move the

Speakers slider.

To adjust the volume level of an application that you are using, move the slider for the corresponding application.

Microphone Level

Follow the steps below to change the microphone recording level.

1.

Right click on the speaker icon on the Taskbar, and select Recording

devices from the sub menu.

User's Manual 3-54

2.

Select Microphone, and click Properties.

3.

On the Levels tab move the Microphone slider to increase or decrease the microphone volume level.

If you feel the microphone volume level is inadequate, move the

Microphone Boost slider to a higher level.

Audio Enhancements

In order to apply the sound effects for your current speaker, follow the steps below.

1.

Right click on the speaker icon on the Taskbar, and select Playback

Devices from the sub menu.

2.

Select Speakers, and click Properties.

3.

On the Enhancements tab select the sound effects you would like, and click Apply.

Realtek HD Audio Manager

You can confirm and change the audio configuration using the Realtek

Audio Manager. To launch the Realtek Audio Manager, click Start ->

Control Panel, select Large icons from View by, then click Realtek HD

Audio Manager.

When you first launch the Realtek Audio Manager, you will see two device tabs. Speakers is the default output device. Microphone is the default input device. To change the default device, click the Set Default Device button under the chosen device tab.

Information

Click the information button to view hardware information, software information, and language setting.

Power Management

The audio controller in your computer can be turned off when the audio function is not used. To adjust the configuration of audio power management, click the Power Management button .

When audio power management is enabled, the circle button at the upper left of the Power Management is blue and convex.

When audio power management is disabled, the button is black and concave.

Speaker Configuration

Click the Auto Test button to confirm the internal speakers or the headphone sound is coming from the right direction.

User's Manual 3-55

Default Format

You can change the sample rate and bit depth of sound.

Video mode

Video mode settings are configured via the Screen Resolution dialog.

To open the Screen Resolution dialog, click Start -> Control Panel ->

Appearance and Personalization -> Display -> Change display

settings.

If you are running some applications (for example a 3D application or video playback and so on), you may see some disturbance, flickering or frame dropping on your screen.

If that occurs, adjust the resolution of display, lowering it until the screen is displayed properly.

Disabling Windows Aero™ may also help correct this issue.

Computer Handling

This section explains computer handling and maintenance.

Cleaning the computer

To help ensure long, trouble-free operation, keep the computer free of dust and dirt, and use care with all liquids around it.

Be careful not to spill liquids into the computer. If the computer does get wet, turn the power off immediately and let the computer dry completely - in these circumstance you should get the computer inspected by an authorized service provider in order to assess the scope of any damage.

Clean the plastics of the computer using a slightly water dampened cloth.

You can clean the display screen by spraying a small amount of glass cleaner onto a soft, clean cloth and then wiping the screen gently with the cloth.

Never spray cleaner directly onto the computer or let liquid run into any part of it. Never use harsh or caustic chemical products to clean the computer.

Moving the computer

While the computer is designed for flexible day-to-day usage you should exercise a few simple precautions when moving it in order to help ensure trouble-free operation.

User's Manual 3-56

Before moving the computer, it is recommended that you change the setting associated with the Hard Disk Drive Protection feature. Please

refer to the section, Heat dispersal , in this chapter for further

information.

Make sure all disk/disc activity has ended before moving the computer

- check that the HDD and other indicators on the front of the computer are off.

Turn off (shut down) the computer.

Disconnect the AC adaptor and all peripherals before moving the computer.

Close the display panel.

Do not pick up the computer by its display panel.

Before carrying your computer, shut it down, disconnect the AC adaptor and allow it to cool down - a failure to follow this instruction may result in minor heat injury.

Be careful not to subject the computer to impact or shock - a failure to follow this instruction could result in damage to computer, computer failure or loss of data.

Never transport your computer with any cards installed - this may cause damage to either the computer and/or the card resulting in product failure.

Always use a suitable carry case when transporting the computer.

When carrying your computer, be sure to hold it securely so that it does not fall or hit anything.

Do not carry your computer by holding any of its protruding elements.

Heat dispersal

To protect against overheating, the processor is equipped with an internal temperature sensor which activates a cooling fan or lowers the processing speed if the computer's internal temperature rises to a certain level. You are able to select whether to control this temperature by either turning on the fan first, then if necessary lowering the processor speed, or by lowering the processor speed first, then if necessary turning on the fan. Both of these functions are controlled through the Power Options.

When the processor's temperature falls within normal range, the fan will be turned off and the processor operation returned to its standard speed.

If the processor's temperature reaches an unacceptably high level with either setting, the computer automatically shuts down to prevent any damage. In this instance all unsaved data in memory will be lost.

User's Manual 3-57