Martin_UG_EN.pdf. Infocus InFocus IN1116LC, InFocus IN1118HD, IN1116, IN1118HDLC, InFocus IN1118HDLC, IN1118HD, IN1116LC
Advertisement
Advertisement
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Important Operating Considerations for Safety
Refer to this guide for proper startup and shutdown procedures.
Follow all warnings and cautions in this manual and on the projector.
Locate the projector at least 4' (1.2m) away from any heating or cooling vents.
Do not block ventilation openings. Locate the projector in a well-ventilated area without obstructions to intake or exhaust vents. Do not place the projector on a tablecloth or other soft covering that may block the vents.
Do not place the projector in direct sunlight, humid, greasy or dusty places or in places where the projector may come into contact with smoke or steam.
Do not touch or block the projector lens with any objects as this can damage the projector lens. Scratches, gouges and other lens damage are not covered by the product warranty.
Do not look directly into the lens while the projector is being used.
Do not drop the projector.
Do not spill liquid on the projector. Spilled liquid may damage the projector.
Use the power cord provided. Connect the power cord to a receptacle with a protective safety (earth) ground terminal. A surge-protected power strip is recommended.
Do not overload wall outlets.
When disconnecting the power cord, hold the plug, not the cord.
Wash hands after handling the cables supplied with this product.
The projector remote control uses batteries. Make sure the batteries’ polarity (+/-) is aligned correctly. Dispose of used batteries in accordance with local disposal laws.
If you choose to install the projector on the ceiling, allow for proper ventilation. The projector warranty does not cover any damage caused by using a second source mounting kit or by installing in an improper location.
When the projector is ceiling mounted, wear protective eyewear to prevent eye injury before opening lamp door.
Refer all service to qualified service personnel. Servicing your own projector can be dangerous to you and will void the warranty.
Only use replacement parts specified by InFocus. Unauthorized substitutions may result in fire, electrical shock, or injury, and may void the warranty.
Only genuine InFocus lamps are tested for use in this projector. Use of non InFocus lamps may cause electrical shock and fire, and may void the projector warranty.
• Hg – Lamp contains mercury. Manage in accordance with local disposal laws. See www.lamprecycle.org.
3
• The projector uses a high-pressure mercury glass lamp. The lamp may fail prematurely, or it may rupture with a popping sound if jolted, scratched, or handled while hot. The risk of lamp failure or rupture also increases as the lamp age increases; please replace the lamp when you see the “Replace Lamp” message.
• In the unlikely event of a lamp rupture, particles may exit through the projector vents.
Please keep people, food, and drinks at least 3’ (1m) away from all projector vents. For ceiling applications, keep people, food and drinks out of the "keep out" area under and around the projector, as indicated by the illustration.
3’ / 1 m 3’ / 1 m
3’ / 1 m
8’ / 2.4 m
5’
/ 1
.5 m
3’ / 1 m
Follow these instructions to help ensure image quality and lamp life over the life of the projector. Failure to follow these instructions may affect the warranty. For complete details of the warranty, see the Warranty Booklet.
After projecting the front of the projector can get uncomfortably warm. Please handle the projector from the rear or left side.
Attention: Hot
Introduction
Your new digital projector is simple to connect, easy to use, and straightforward to maintain. It is a versatile projector that is flexible enough for business presentations and home video viewing too. The IN1116 has native WXGA 1280 x
800 resolution, and IN1118HD has native 1080p 1920 x 1080 resolution. They are compatible with a wide variety of computers and video devices.
Product specifications
To read the latest specifications on your multimedia projector, be sure to visit our website at www.infocus.com, as specifications are subject to change.
Accessories
The standard accessories that came with your projector are listed in the included
Quick Start Guide. Optional accessories can be found on our website at www.infocus.com/support or at your retailer or dealer.
Online registration
Register your projector on our website at www.infocus.com/register to activate your warranty and receive product updates, announcements, and registration incentives.
focus lamp cover remote control receiver (IR) lens keypad zoom security bar power cord connector connector panel
4
Connector panel
The projector provides both computer and video connection options.
• USB type A (2): for standard wireless mouse/keyboard, USB storage devices to be accessed by LightCast.
• M-USB type B for firmware upgrades, slide advance and Screen Saver prevention
• Audio output for external speakers
• Audio input for video and computer sources
• Video
• VGA computer
• HDMI
USB A
M-USB
USB A Video
Computer
HDMI
Audio Out
Audio In security lock
5
Positioning the projector
•
•
•
•
•
To determine where to position the projector, consider the size and shape of your screen, the location of your power outlets, and the distance between the projector and the rest of your equipment. Here are some general guidelines:
Position the projector on a flat surface at a right angle to the screen. The projector must be at least 39.4” (1.0m) from the projection screen.
If you are installing the projector on the ceiling, allow for proper ventilation. The projector warranty does not cover any damage caused by using a second source mounting kit or by installing in an improper location.
The projector can be mounted on a tripod or other structure using a single 1/4-
20” screw. Thread depth must be at least three rotations or 4mm. The locating pin is 14mm away center to center.
To turn the image upside down, see “Ceiling mount” on page 26.
Position the projector the desired distance from the screen. The distance from the lens of the projector to the screen and the video format determine the size of the projected image.
60 inches high image
Projection angle bottom of image 9 inches above center of lens lens center
Diagonal Screen Size
(inches/m)
40”/1.0m
60”/1.5m
80”/2.0m
100”/2.5m
150”/3.8m
Table 1: IN1116 (WXGA) Screen size
Throw Ratio = 1.15 to 1.5
Size of the
Projected Image
Width
(inches/m)
38”/1.0m
58”/1.5m
77”/2.0m
96”/2.4m
144”/3.7m
Distance to screen
Minimum distance
(inches/m)
44”/1.1m
66”/1.7m
88”/2.3m
111”/2.8m
166”/4.2m
Maximum distance
(inches/m)
58”/1.5m
87”/2.2m
115”/3.0m
144”/3.7m
216”/5.5m
Diagonal Screen Size
(inches/m)
40”/1.0m
60”/1.5m
80”/2.0m
100”/2.5m
150”/3.8m
Table 2: IN1118HD (1080p) Screen size
Throw Ratio = 1.15 to 1.5
Size of the
Projected Image
Width
(inches/m)
43”/1.1m
64”/1.6m
85”/2.2m
107”/2.7m
160”/4.1m
Distance to screen
Minimum distance
(inches/m)
49”/1.3m
74"/1.9m
98”/2.5m
123”/3.1m
184”/4.7m
Maximum distance
(inches/m)
64”/1.6m
96”/2.4m
128”/3.3m
160”/4.1m
240”/6.1m
Minimum Distance to Screen
39.4"/1.0m
Offset
15%+-5%
Offset for 60in. Image
9"/22.9cm
6
Connecting a computer source
VGA connection
Connect one end of the provided computer cable to the Computer In connector on the projector and the other to the VGA connector on your computer. If you are using a desktop computer, you will need to disconnect the monitor cable from the computer’s video port first.
HDMI connection
HDMI is a standard, uncompressed, all-digital audio/video interface. HDMI provides an interface between sources, such as set-top boxes, DVD players, and receivers and your projector. Plug an HDMI cable into the video-out connector on the video device and into the HDMI connector on the projector.
Connecting power
Connect the black power cord to the Power connector on the rear of the projector and to your electrical outlet. The Power LED turns steady amber.
By
default, the Power Saving feature is off. You can change the setting, see page 27.
NOTE: Always use the power cord that shipped with the projector.
Optional computer connections
To get sound from the projector, connect an audio cable (optional cable, not included) to your computer and to the Audio In connector on the projector. You may also need an adapter.
connect VGA cable connect HDMI connect power connect audio cable
7
Displaying an image
Press the Power button.
The Power LED blinks green, and the fans start to run. When the lamp comes on, the start up screen displays and the Power LED turns solid green. It can take up to a minute for the image to achieve full brightness. Note: When the feature, AC
Power On, is enabled, the projector automatically turns on when power is connected. This allows control of ceiling mounted projectors with a wall power switch.
No start up screen? Get help on page 12.
Turn on your computer or video device.
The image should appear on the projection screen. If it doesn’t, press the Source button on the projector’s keypad or remote.
If you are using a VGA cable to connect your computer to the projector:
If using a laptop, make sure its external video port is active.
Many laptops do not automatically turn on their external video port when a projector is connected. Usually a key combination like FN + F8 or CRT/LCD key turns the external display on and off. Locate a function key labeled CRT/LCD or a function key with a monitor symbol. Press FN and the labeled function key simultaneously.
Refer to your laptop's documentation for more information about your laptop's key combination.
press Power button turn on computer or video device activate laptop’s external port monitor key or
LCD/CRT key
FN key
No laptop image? Try pressing the Auto Image button on the remote. Get
8
Adjusting the image
If necessary, adjust the height of the projector by pressing the elevator foot button to extend the foot.
Avoid placing your hands near the hot exhaust vent at the front of the projector.
Position the projector the desired distance from the screen at a 90 degree angle to the screen.
See page 6 for a table listing screen sizes and distances.
adjust height adjust distance elevator foot button
Adjust the zoom or focus.
adjust zoom and focus
If the image is not square, first make sure that the projector is perpendicular to the screen. If the image is larger or smaller on the top or bottom edge of the screen, press the top Keystone button to reduce the upper part of the image, and press the bottom Keystone button to reduce the lower part.
If the left or right side of the screen is larger or smaller the other, you can turn the projector to the left or to the right a few degrees to square the image.
Adjust the Contrast or Brightness in the Basic Menu. See page 24 for help with
these menu adjustments.
adjust keystone adjust Basic Menu
9
Connecting a video device
You can connect video devices such as VCRs, DVD players, camcorders, digital cameras, video game consoles, HDTV receivers, and TV tuners to the projector.
You can connect the audio directly to the projector to get sound from the built-in speaker, or you can bypass the projector’s audio system and connect the audio directly from your source to a stereo or home theater system.
You can connect the projector to most video devices that can output video. You cannot directly connect the coaxial cable that enters your house from a cable or satellite company, the signal must pass through a tuner first. Examples of tuners are digital cable boxes, VCRs, digital video recorders, and satellite TV boxes. Basically, any device that can change channels is considered a tuner.
Before connecting your projector, you should decide which aspect ratio you want to use. The projector’s Aspect Ratio setting is accessed through the Resize button
on the remote or through the projector’s Basic Menu. See page 24 for more
information.
Video device connections
No video cables are provided with the projector. You can order cables from
InFocus or provide your own.
LightCast Reader
Plug a USB thumb drive into one of the USB A connectors. See LightCast Reader® on page 28.
HDMI connection
HDMI is a standard, uncompressed, all-digital audio/video interface. HDMI provides an interface between sources, such as set-top boxes, DVD players, and receivers and your projector. Plug an HDMI cable into the video-out connector on the video device and into the HDMI connector on the projector.
Composite video connection
Plug the composite video cable’s yellow connector into the video-out connector on the video device. Plug the other yellow connector into the yellow Video connector on the projector.
10
VGA connection
If your video device has a 15-pin VGA output, plug one end of the included computer cable into the VGA connector on your video source. This connector may be labeled “To Monitor” on the video source. Plug the computer cable into the Computer In connector on the projector.
Component video connection
If your HD video device has component connectors, an optional Component to
VGA adapter can be used. Plug the component cable into the video device. Plug the other end of the component cable into the adapter and plug the adapter into the Computer In connector.
Audio
For audio, connect a 3.5mm stereo cable to the Audio In connector on the projector and to your source. If your source uses RCA audio connectors, a Y-cable or adapter may be used. (Note: A separate audio connection is not required for
HDMI source inputs.)
Shutting down the projector
Auto Off Time
The projector also has an Auto Off Time feature that automatically turns the projector off after no active sources are detected and no user interaction with the projector is performed for 30 minutes. By default, this feature is off. You can
change the length of time, see page 27.
Turning off the projector
To turn the projector off, press the Power button on the remote or keypad. The lamp turns off and the Power LED blinks amber for 30 seconds while the fans continue to run to cool the lamp. Unplug the power cable to completely power off the projector.
Troubleshooting your setup
If your image appears correctly on the screen, skip to the next section. If it does not, troubleshoot the setup.
The Status Indicator LEDs on top of the projector indicate the operational state of the projector and can help you with troubleshooting.
Operational Mode
Normal operation
Powering up
Powering down
Standby
Fan failure
Lamp failed to ignite
Lamp is at the end of its life
Projector is overheating
Table 3: Status Indicator LEDs
Status Indicator Lights
POWER: Solid green
TEMP: Off
LAMP: Off
SERVICE: Off
POWER: Blinks green
TEMP: Off
LAMP: Off
SERVICE: Off
POWER: Blinks amber
TEMP: Off
LAMP: Off
SERVICE: Off
POWER: Solid amber
TEMP: Off
LAMP: Off
SERVICE: Off
POWER: Blinks amber
TEMP: Off
LAMP: Off
SERVICE: Blinks red
POWER: Solid amber
TEMP: Off
LAMP: Solid amber
SERVICE: Solid red
POWER: Solid amber
TEMP: Off
LAMP: Solid amber
SERVICE: Off
POWER: Solid amber
TEMP: Solid yellow
LAMP: Off
SERVICE: Off
11
Problem
No start up screen
Only start up screen appears
Startup
Screen
A
Solution
Plug power cord into the projector press the Power button
Result
Correct image
Startup
Screen
Press the SOURCE button activate laptop’s external port
Restart laptop
Computer image projected
A
A
12
Problem
No computer image, just the words “Signal out of range”
Solution
Press the Auto Image button on remote.
Adjust computer refresh rate. Varies per operating system.
Signal out of
the range
Result
Computer image projected
A
A
Only my laptop’s background appears, not the
Desktop icons
A
A
You may also need to set a different resolution on your computer, as shown in the following problem, “image fuzzy or cropped”
Change the Multiple Display setting to “Duplicate these displays.” Varies per operating system.
Background and Desktop projected
A
A
A
13
Problem
Image fuzzy or cropped
A
A
Solution
Change the computer's "Resolution" setting to match the projector's resolution. Varies per operating system.
Result
Image clear and not cropped
A
Image not centered on screen Move projector, adjust height
Adjust horizontal or vertical position in
Advanced Menu >
Image > PC... menu
14
Correct image
Problem
Image not square
Image not sharp
Solution
Adjust Keystone on keypad
Result
Square image
Adjust Sharpness in the Basic Menu
Correct image
Image does not fit 4:3 or 16:9 screen Change aspect ratio to 4:3 or 16:9 in Basic Menu >
Aspect Ratio menu
Correct image
15
Problem
Image upside down A
Solution
Turn off Ceiling Mount in Basic menu
Result
Correct image
Image reversed left to right
A
Projected colors don’t match source
COLOR
Turn off Rear Project in Advanced Menu > Setup >
Image Setup... menu
Correct image
Adjust the items in the Advanced Menu > Image >
Color... menu
Correct image
COLOR
16
Problem
The video embedded in my PowerPoint presentation does not play on the screen
Solution
Turn off the internal LCD display on your laptop
A
B
A
B
Result
Embedded video plays correctly
A
B
Lamp won’t turn on, the projector is overheating
Make sure vents aren’t blocked, turn off the projector and allow it to cool for one minute
Lamp turns on
Startup
Screen
Overheating indicator
17
Problem
“Replace lamp” message appears at startup or lamp won’t turn on
Solution
Lamp must be replaced (see page 32)
lamp door
Result
Lamp turns on
Startup
Screen
replace lamp
Still need assistance?
If you need assistance, visit our website at www.infocus.com/support or call us. See the Quick Start Guide for support contact information.
This product is backed by a limited warranty. An extended warranty plan may be purchased from your dealer. When sending the projector in for repair, we recommend shipping the unit in its original packing material, or having a professional packaging company pack the unit. Please insure your shipment for its full value.
18
Using the remote control
The remote uses two (2) AAA batteries (not provided). They are easily installed by removing the cover from the remote’s back, aligning the + and - ends of the batteries, sliding them into place, and then replacing the cover.
Caution:
• When replacing the remote batteries, be aware that using batteries other than AAA batteries may risk severe damage to the remote. When disposing of the batteries, be sure to do so in an enviromentally proper manner.
• If the remote control gets wet, wipe it dry immediately.
• Avoid excessive heat and humidity.
• Ensure the batteries' polarity (+/-) is aligned correctly.
• Do not mix new and old batteries together, or mix different types of batteries together.
• Replace the batteries as soon as they run out.
• Remove batteries from the remote control when storing or not in use for a prolonged period.
To operate, point the remote at the front of the projector (not at the computer).
The range of optimum operation is about 15 feet (4.5m).
Press the remote’s Power button to turn the projector on and off (see page 8 for
shutdown info).
Press the remote’s Menu button to open the projector’s menu system. Use the arrow buttons to navigate, and the Select button to select features and adjust
values in the menus. See page 23 for more info on the menus.
The remote also has:
• Volume buttons adjust the sound.
• Custom button that can be assigned to a special function, like Blank Screen or
• Source button brings up a menu of all possible sources allowing the user to switch the active source.
• Blank button to blank the screen.
•
Presets button to select stored settings (see page 24).
• Mute button to silence the audio.
19
• Auto Image button to resynch the projector to the source.
•
Resize button to switch among aspect ratios (see page 24).
• Help button to get help with connecting sources and improving the picture.
• ESC to go back to previous OSD menu or to return to home screen when using LightCast source.
• PC button to cycle through the computer sources.
• Video button to cycle through the video sources.
• Keystone buttons adjust the squareness of the image
• Magnify buttons magnify and reduce the projected picture size.
• Freeze button to pause the projected image.
• Overscan button remove noise around the video image.
• AV Mute button blanks the projected image and mutes audio.
Lightcast and the remote
When using Lightcast, the ESC button acts as the Home key and navigation keys are used for navigating LightCast.
Troubleshooting the remote
• Make sure the batteries are installed in the proper orientation and are not dead.
• Make sure you’re pointing the remote at the projector or the screen, not the computer, and are within the remote range of 15 feet (4.5m). For best results, point the remote at the projector.
navigation buttons
Using the audio
Using the projector’s speaker
Connect the audio source to the Audio In connector to hear audio through the projector speaker.
Amplified speakers may also be connected to the projector using the Audio Out connector.
To adjust the volume, press the Volume buttons on the remote.
Troubleshooting Audio
If you aren’t hearing the audio, check the following:
• Make sure the audio cable is connected to the Audio In connector on the projector, and that the other end of the cable is connected to an Audio Out connector on the source (not a “line-in” or “microphone” connector).
• Make sure the volume is turned up enough. Press the Volume button on the remote.
• Make sure the correct source is active.
• Adjust the audio source.
• If playing a video, make sure the playback has not been paused.
connect audio cable
20
Using the keypad buttons
Most buttons are described in detail in other sections, but here is an overview of their functions:
Power–turns the projector on and off (page 8).
Auto - Resynchronizes the projector to the source.
Preset - Toggles between the projector presets.
Right arrow - When the menu or LightCast is displayed, the right arrow button is used for navigating.
Up arrow/Keystone - When the menu or LightCast is displayed, the up arrow button is used for navigating. When the menu is not displayed, this button adjusts the
squareness of the image (page 9).
Down arrow/Keystone - When the menu or LightCast is displayed, the down arrow button is used for navigating. When the menu is not displayed, this button
adjusts the squareness of the image (page 9).
Left arrow - When the menu or LightCast is displayed, the left arrow button is used for navigating.
Menu - Turns on the On-Screen Display (OSD) menu. Goes back to previous OSD menu, exits and saves menu settings.
Select - Activates the selected On-Screen Display (OSD) menu item and selects highlighted items in LightCast.
Source - Brings up a menu of available sources.
21
menu navigation buttons
Optimizing computer images
After the projector is running and the image is on the screen, you can optimize the image using the onscreen menus. For general information on using the menus, see
• Select default image settings using a preset appropriate to your environment.
•
Adjust the Keystone, Contrast, or Brightness (page 24).
• Change the Aspect Ratio. Choose the option that best fits your input source
•
Adjust the Color Temperature (page 25).
•
Adjust the Phase, Tracking, or Horizontal or Vertical position (page 25).
• Once you have optimized the image for a particular source, you can save the settings using Presets. This allows you to quickly recall these settings later
Presentation features
Several features are provided to make giving presentations easier. Here is an overview, details are found in the menu section.
• The Custom key allows you to assign various features to the button. The default effect is Source Info, which displays information about the projector
and current source. See page 26 for details.
• The Search Screen option lets you change the appearance of the blank screen
• A Timer is provided to automatically shut down the projector after several
minutes. This helps preserve lamp life (page 26).
• When the projector is connected to the computer via M-USB, the up and down arrows an be used as page up and page down controls.
• When the projector is connected to the computer via M-USB, the projector will prevent the computer from going into screen saver mode during your presentation.
Optimizing video images
After your video device is connected properly and the image is on the screen, you can optimize the image using the onscreen menus. For general information on
•
Adjust the Keystone, Contrast, Brightness, Color, or Tint (page 24).
• Change the Aspect Ratio. Choose the option that best fits your input source
•
Select a Sharpness setting (page 24).
•
Adjust the Color Temperature. Select a listed warmth value (page 25).
•
Turn on Overscan to remove noise on the edges of the image (page 25).
Customizing the projector
You can customize the projector for your specific setup and needs. See page 26 for
details on these features.
• For rear projection, turn Rear Project on in the Advanced Menu > Setup >
Image Setup... menu.
• For ceiling mounted projection, turn Ceiling Mount on in the Basic menu.
• Specify which source the projector checks first for active video during powerup.
• Specify the function of the Custom key on the remote.
• Turn the projector’s display messages on and off.
• Turn on power saving features.
• Specify appearance of blank screen.
• Specify the language viewed on the menus.
• Save settings for the active source as a preset.
22
Using the menus
1
To open the menus, press the Menu button on the keypad or remote. (The menus automatically close after 60 seconds if no buttons are pressed.) Use the arrow buttons to move up and down to review the menu options.
2
To enter a submenu, highlight the desired submenu and press Select on the keypad or remote.
3
To adjust a menu setting, highlight the desired menu option and press < or > to scroll through the available adjustments.
4
Press the Menu button to exit the menu system.
The menus are grouped by usage:
• The Basic Menu provides common adjustments.
• The Advanced Menu provides more complex adjustments.
keypad navigation buttons
Basic Menu Advanced Menu
23
Basic Menu
To adjust the following settings, highlight the setting, use the right and left arrows to adjust the values.
Aspect Ratio: Aspect ratio is the ratio of the image width to image height. TV screens are usually 4:3. HDTV and most DVDs are 16:9.
Select Auto to have the projector choose the ratio. Choose Native to see the unmodified input with no resizing by the projector. Select 16:9 to watch enhanced widescreen DVDs.
Auto Image: resets the projector to the source.
Brightness: changes the intensity of the image.
Contrast: controls the degree of difference between the lightest and darkest parts of the picture and changes the amount of black and white in the image.
Auto Keystone: automatically corrects distorted images resulting from an angled projection.
Keystone: adjusts the image vertically and makes a squarer image. You can also adjust keystone from the keypad.
Presets: Presets are provided that optimize the projector for displaying computer presentations and video images under certain conditions. Note: Users can save their settings as a User Preset.
Sharpness: Changes the clarity of the edges of a video image. Select a sharpness setting.
Volume: increases or decreases the audio volume.
Ceiling Mount: turns the image upside down for ceiling-mounted projection.
Basic Menu increasing keystone decreasing keystone
24
Advanced Menu
Advanced Menu
Image:
3D Control:
3D: allows you to enjoy 3D (stereoscopic) content. Your projector supports
Auto, Top-Bottom, Frame Sequential, Frame Packing, Side-by-Side for controlling LCD shutter glasses. In addition to the projector, you will need a pair of
3D shutter glasses, 3D content, and 3D compatible source (and emitter).
Ensure the glasses you choose are consistent with the synchronization mode you will be using.
3D Sync Invert: If the image appears to flutter, look odd or if the image depth looks off or you experience eye strain, turn this feature on to see if the image improves.
Color...
Color: adjusts a video image from black and white to fully saturated color.
The color setting applies to video sources only.
Red/Green/Blue Gain: adjusts the gain of the red, green or blue channel of the image.
Red/Green/Blue Offset: adjusts the offset of the red, green or blue channel of the image.
Color Space: applies to computer and component video sources. It allows you to select a color space that has been specifically tuned for the input signal.
When Auto is selected, the projector automatically determines the standard.
To choose a different setting, turn off Auto, then choose RGB for computer sources or choose either REC709 or REC601 for component video sources.
Color Temperature: changes the intensity of the colors. Select a listed relative warmth value.
Gamma: select the appropriate gamma from among Video, Film, Bright, and
CRT.
Tint: adjusts the red-green color balance in the image of NTSC video images.
The tint setting applies to NTSC video sources only.
White Intensity: increases the brightness of whites that are near 100%.
PC:
Phase: adjusts the horizontal phase of a computer source.
Prevent PC Screen Saver: prevents your computer from going into Screen
Save mode. The projector must be connected to the PC via a USB cable for this feature to work.
Sync Threshold: (progressive signals only) If a hardware device, such as a DVD player, is not syncing properly with the projector, select this option to help it to sync when connected to the projector.
Tracking: adjusts the vertical scan of a computer source.
Horizontal/Vertical Position: adjusts the position of a computer source.
Video:
Overscan: removes noise around the video image.
25
Setup:
Audio Setup...
Internal Speaker: turns the internal speaker on or off.
Computer In: selects the audio input for Computer In signal.
Video: selects the audio input for video source.
HDMI: select the audio input for HDMI signal.
Closed Captioning...
Closed Captions
:
controls closed captioning. If the source is NTSC and contains captions on the selected channel, then the projector will display caption text overlaid on the image. When Closed Captions is off and volume is muted, closed captioning will appear. Options are: Off, CC1 and CC2.
Image Setup...
Digital Zoom: reduces the size of projector’s display area. If the display area has been resized by this setting, it can be moved by changing the Horz Shift and Vert Shift settings.
•
•
•
•
•
• Auto Image : resets the projector to the source.
Freeze Screen : pauses the projected image.
Source Info : the default action. Shows the Source Info menu.
Projector Info : shows the Projector Info menu.
Overscan : removes noise around the image.
AV Mute: enables or disables AV Mute function.
• Closed Captions: enables or disables Closed Captions.
Keypad: enables or locks the projector keypad.
Lamp...
Programmed Dimming: When enabled, Programmed Dimming enhances contrast ratios in dark scenes. Programmed Dimming will impact lamp life and system noise performance. Programmed Dimming works in conjunction with the lamp.
OSD Setup...
Language: allows you to select a language for the onscreen display.
Magnify Level: magnifies the image. If the image has been magnifiedby this setting, it can be moved by changing the Horz Shift and Vert Shift settings.
Ceiling Mount: turns the image upside down for ceiling-mounted projection.
Rear Project: reverses the image so you can project from behind a translucent screen.
Keypad/Remote Settings...
Blank Key: select what to display when the blank key on the remote is pressed: the factory logo screen or a solid color screen (blue, black or white).
Custom Key: allows you to assign a different function to the Custom button, allowing you to quickly and easily use the effect. Highlight an effect and press ^ or v on the keypad or Select on remote to choose a different one.
•
•
•
Blank Screen : displays a solid color or factory logo screen.
Mute : turns off all sound.
Source : brings up a menu of available sources.
26
Menu Position: allows you to change the position of the On Screen Display items.
Menu Transparency: allows you to change how much of the projected image behind the menu you can see. As the value increases, more of the image behind the menu is visible.
Show Messages: displays status messages (such as “Searching”) in the lowerleft corner of the screen.
PIN Settings
PIN Protect: The PIN (personal identification number) feature allows you to password protect your projector. Once you enable the PIN feature, you must enter the PIN before you can project an image. Use the Up/Down/Left/Right arrows buttons on the remote or keypad to set a 4-button press sequence. If you enter an incorrect PIN 3 times in succession, the projector will automatically shut down. If you lose or forget your custom PIN, contact InFocus Technical Support.
To enter the PIN at projector startup:
Power up the projector. The “Enter PIN” dialog box appears after the startup screen. Enter the default PIN (Left/Right/Up/Down) or the new PIN if it has been changed, using the arrow buttons on the remote or keypad. See the description above for instructions.
To change the PIN:
Select “Change PIN...” in the Advanced Menu > Setup > PIN settings menu.
Enter the existing PIN. Enter the new PIN twice. Do not forget the new PIN.
Contact InFocus Support to recover a projector with a forgotten PIN.
Power
Power Saving Mode: When the Power Saving Mode is On and the projector is in standby (powered off but connected to AC power) and the Audio Out function will not work.
AC Power On: When this feature is enabled, the projector automatically turns on when power is connected. This allows control of ceiling mounted projectors with a wall power switch.
Instant Power On: When this feature is enabled and it has been less than 1 minute since the projector was powered down, you can turn the projector back on immediately. When this feature is disabled, you will need to wait for the projector lamp to completely cool before restarting the projector.
Eco Blanking: When this feature is enabled and no video source is sensed,
70% of lamp power is saved and no image is shown. When the video source is again applied, the image is shown immediately.
Source
Auto Source: When this feature is On, the projector automatically finds the active source, checking the selected Power-up Source first. When this feature is Off, the projector defaults to the source selected in Power-up Source. To display another source, you must manually select one by pressing the Source button on the remote or keypad and selecting one from the displayed Source menu.
Power-up Source: determines which source the projector checks first for active video during power-up.
Search Screen: allows you to display a blank screen instead of the default screen at startup, and when no source is detected.
Timer
Auto Off Time: automatically turns the projector off after no signals are detected for a preset number of minutes. If an active signal is received before the projector powers down, the image will be displayed.
High Altitude Setting
High Altitude: We recommend you turn on the High Altitude Mode when your environment is between 5000' (1500m) and 10,000' (3000m) above sea level.
Status/Service:
Source Info: a read-only display of current source settings.
Projector Info: a read-only display of current projector settings and lamp hours.
Reset Lamp Hours...: resets the lamp hours used counter in the Projector Info menu to zero. Do this only after changing the lamp.
Factory Reset...: restores all settings to their default.
Service Code...: only used by authorized service personnel.
27
LightCast Reader
LightCast is a document, picture and movie viewer which can read files off a USB disk or from the internal 4.2GB memory and project them. In addition, files can be copied, pasted, and deleted from both the USB disk and internal memory. To control the LightCast reader, use the projector remote and keypad, or a third party wireless mouse and keyboard.
File type
Picture
Document
Video
Table 4: File compatibility/limits
Format bmp, jpg, png
Microsoft Office 2003, ’07, ’10, ‘13 doc, docx, ppt, pptx, xls, xlsx, pdf
3gp, avi, divx, flv, m4v, mkv, mov, mp4, rmvb, ts/tp, wmv
Basic operation
1
Press the Source button on either the remote or keypad.
2
Navigate to LightCast and press the Select button on the remote or keypad.
3
To display a file located in the projector's internal memory, navigate to the
Local directory tab using the arrow buttons on the remote or keypad and press the Select button.
4
To display a file located on an external drive (such as a USB thumb drive), insert the drive into either the USB-1 or USB-2 connector on the rear panel.
Then navigate to the USB directory tab using the arrow buttons on the remote or keypad and press the Select button.
5
Navigate to the desired file and press Select.
28
6
Once the file displays, a file controls submenu appears. Features vary based on the file type.
To copy and paste a file or folder to another location:
1
Press the Source button on either the remote or keypad.
2
Navigate to LightCast and press the Select button on the remote or keypad.
3
Navigate to the Local or USB directory tab that contains the item you wish to copy.
4
Navigate to More and press Select.
7
Navigate to the desired feature and press Select to activate the feature.
8
Select Return to return to the file directory.
5
Navigate to Copy and press Select.
29
6
Navigate to the item you wish to copy and press Select. A green checkmark appears next to the selected item.
7
Navigate to the Local or USB directory tab.
8
Navigate to the location you wish to paste the item into and press Select.
9
Navigate to Paste and press Select.
30
Maintenance
Cleaning the lens
1
Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
• Projector must be off and the lens must be at room temperature.
• Avoid using an excessive amount of cleaner, and don’t apply the cleaner directly to the lens. Abrasive cleaners, solvents or other harsh chemicals might scratch the lens.
2
Lightly wipe the cleaning cloth over the lens in a circular motion.
WARNINGS:
• Turn the projector off and unplug power cord before cleaning any part of the projector.
• Do not touch or block the projector lens with any objects as this can damage the projector lens. Scratches, gouges and other lens damage are not covered by the product warranty.
• Do not open any cover on the projector, except the lamp cover.
• Do not attempt to service this product yourself as opening and removing covers may expose you to dangerous voltage and other hazards. Refer all servicing to qualified service personnel.
Using the security lock
The projector has a security lock for use with a Cable Lock System. Refer to the information that came with the lock for instructions on how to use it.
31
Security Lock
Replacing the projection lamp
The Lamp Hours timer in the Projector Info menu counts the number of hours the lamp has been in use.
• NOTE: Be sure to use the InFocus lamp module designed for this projector.
You can order new lamps from www.infocus.com (in select areas), your retailer or your dealer. Only genuine InFocus lamps are tested for use in this projector. Use of non InFocus lamps may cause electrical shock and fire, and may void the projector warranty. InFocus is not liable for the performance, safety or certification of any other lamps.
WARNINGS:
• The projector uses a high-pressure mercury glass lamp. The lamp may fail prematurely, or it may rupture with a popping sound if jolted, scratched, or handled while hot. The risk of lamp failure or rupture also increases as the lamp age increases; please replace the lamp when you see the “Replace Lamp” message.
• To avoid burns, allow the projector to cool for at least 60 minutes before you replace the lamp.
• Do not touch or block the projector lens with any objects as this can damage the projector lens. Scratches, gouges and other lens damage are not covered by the product warranty.
• Unplug the power cord before replacing the lamp.
• Do not drop the lamp module. The glass may shatter and cause injury.
• Do not touch the glass surface of the lamp module. Fingerprints can obscure projection sharpness and may cause the glass to shatter.
• Be extremely careful when removing the lamp housing. In the unlikely event that the lamp ruptures, small glass fragments may be generated. The lamp module is designed to contain most of these fragments, but use caution when removing it.
• Before replacing a ruptured lamp, clean the lamp compartment and dispose of cleaning materials. Wash hands after lamp replacement.
• When replacing the lamp while the projector is ceiling-mounted, wear protective eyewear to prevent eye injury.
Hg – Lamp contains mercury. Manage in accordance with local disposal laws. See www.lamprecycle.org.
32
1
Turn off the projector and unplug the power cord.
2
Wait 60 minutes to allow the projector to cool thoroughly.
3
Remove the lamp door, press down on the button in the center of the lamp door and remove the end cover.
4
Remove the screw holding the lamp door, slide the door to the right and lift the door off the projector.
5
Loosen the captive screws that attach the lamp housing to the projector.
NOTE: If the projector is installed on a ceiling mount, be careful not to drop the lamp module once the captive screws are loosened.
6
Carefully lift the lamp straight up, off of the alignment pins; being careful not to pinch the lamp connector. Dispose of the lamp in an environmentally proper manner.
7
Install the new lamp module, aligning the pins properly. Be careful not to pinch the lamp connector.
8
Tighten the screws. (NOTE: If the pins have not been aligned properly, the screws will not tighten securely.)
9
Replace the lamp door by (a) putting the lamp door down and (b) sliding it to the left.
10
Replace the lamp door screw and tighten securely.
11
Replace the end cover.
12
Plug in the power cord and press the Power button to turn the projector back on.
13
To reset the lamp hour timer, navigate to the Advanced Menu > Status/Service menu and select Reset Lamp Hours....
33
turn off and unplug projector wait 60 minutes loosen screws
Download
Public link updated
The public link to your chat has been updated. You may view and manage your chat links after registration here.
Document public link
Advertisement