advertisement
Troubleshooting
If there is a problem with your TV please refer to the table below to determine the symptoms, then carry out the suggested check. If this does not solve the problem, please contact your local Panasonic dealer, quoting the model number and serial number (both found on the rear of the TV).
Picture
Symptoms
Sound
Checks
Aerial location, direction or connection
Snowy Picture
Noisy Sound
Multiple Images
Interference
Normal Picture
No Picture
Normal Sound
Noisy Sound
No Sound
No Sound
Aerial location, direction or connection
Electrical appliances
Cars / Motorcycles
Fluorescent lights
Switch on P-NR in Picture menu to reduce picture noise.
Volume level
Sound mute switched on.
TV set to AV mode.
Not plugged into AC outlet.
Not switched on.
Picture / Sound controls set at minimum levels.
Check if in Standby mode.
Colour controls set at minimum levels.
No Colour
Normal Sound
Retune Channel (s).
Poor or Distorted Picture
Weak or No Sound
Normal Picture
There may be red spots, blue spots and green spots on the screen.
Weak or Distorted
Sound
Sound reception may have deteriorated.
Switch NICAM setting (Sound menu) to Off until reception improves.
Normal Sound
Poor Video.
(Snow noise, no picture, picture runs, etc.)
H
D
M
I
Poor Audio.
The error message appears.
„Control with HDMI“ function does not work
This is a characteristic of liquid crystal panels and is not a problem. The liquid crystal panel is built with very high precision technology giving you fi ne picture details. Occasionally, a few non-active pixels may appear on the screen as a fi xed point of blue, green, or red.
Please note this does not affect the performance of your LCD.
HDMI cable is not connected securely.
Turn the power supply of the TV and connected equipment off then turn on.
Check compatibility of input signal from the connected equipment.
The connected equipment must be EIA/CEA-861/861B compliant.
Change the audio setting of the connected equipment to L.PCM.
Check the setting of HDMI input in Sound menu.
If the problem is due to the digital audio connection, change to the analogue audio connection.
Please consult an Authorized Service Center.
Switch the TV unit on again with the equipment on. Set „Control with
HDMI“ to „Off“, then set to „On“ again (see page 13).
33
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 2 Accessories
- 3 Warnings and Precautions
- 4 Fitting remote control batteries
- 5 Installation
- 5 How to use the LCD stand
- 5 Maintenance
- 6 Quick Start Guide
- 9 Basic controls: control panel and remote control
- 10 Using the On Screen Displays
- 10 Programme guide
- 11 Picture menu
- 12 Sound menu
- 13 Setup menu
- 14 Tuning menu – overview
- 15 Tuning menu – Programme edit
- 15 Adding / deleting a programme channel
- 15 Moving a programme channel
- 15 Tuning a programme channel
- 16 Renaming a programme channel
- 16 Locking a programme channel
- 16 to a recording device
- 17 Tuning menu – Auto setup
- 18 Tuning menu – Manual tuning
- 18 Manual tuning (via control panel)
- 19 Owner ID
- 20 Shipping condition
- 21 Q-Link
- 22 Aspect Controls
- 24 VCR / DVD operation
- 25 Teletext operation
- 27 Still
- 28 Connections
- 29 How to connect the AV1 / 2 Scart terminals
- 29 How to connect the Component Input terminals
- 30 How to connect the HDMI 1/2 Input terminals
- 31 Control with HDMI "HDAVI Control
- 32 Input signal that can be displayed
- 32 Scart, S-video and HDMI terminals information
- 33 Troubleshooting
- 34 cations