- Home
- Do-It-Yourself tools
- Garden tools
- Lawnmowers
- Toro
- TITAN ZX4820 Zero-Turn-Radius Riding Mower
- User manual
advertisement
Setup
Loose Parts
Use the chart below to verify that all parts have been shipped.
Description Procedure
1
2
3
No parts required
Ignition Key
Hose coupling
Operator's Manual
Engine Operator's Manual
Operator Training Material
No parts required
Qty.
–
1
1
1
1
1
–
Use
Connect the battery.
Complete the Setup.
Check the mower adjustment.
1
Connecting the Battery
No Parts Required
Procedure
1. Locate the battery and negative battery cable in the center of the machine.
2. Remove the black plastic cap from the negative battery post. Remove the fasteners from the negative battery cable and use them to secure the negative
battery cable to the negative battery post (Figure 4).
3
4
5
2
1
G010257
1.
Bolt
2.
Washer
3.
Negative battery cable
Figure 4
4.
Negative battery post
5.
Nut
2
Completing the Setup
Parts needed for this procedure:
1
1
1
1
1
Ignition Key
Hose coupling
Operator's Manual
Engine Operator's Manual
Operator Training Material
Procedure
Setting Up the Motion Control Levers
If needed, remove the upper bolt, washer and nut and raise the motion control levers to the upright position.
Secure the motion control levers. Refer to Adjusting the
Motion Control Levers in the Operation Section.
Raising the ROPS
Raise the ROPS into the upright position and secure it in place. Refer to Using the Rollover Protection System
(ROPS) in the Operation Section.
Checking the Tire Pressure
Check the front and rear tires for proper inflation. Refer to Checking the Tire Pressure in the Operator's Manual for the recommended inflation pressure.
Checking the Side Discharge Chute
Remove the packing restraint holding the side discharge chute up and lower the chute into place.
13
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 2 Introduction
- 4 Safety
- 4 Safe Operating Practices
- 6 Toro Riding Mower Safety
- 7 Slope Indicator
- 8 Safety and Instructional Decals
- 13 Setup
- 13 1 Connecting the Battery
- 13 2 Completing the Setup
- 14 3 Checking the Mower Adjustment
- 15 Product Overview
- 16 Controls
- 17 Operation
- 17 Think Safety First
- 18 (ROPS)
- 19 Adding Fuel
- 20 Checking the Engine Oil Level
- 20 Operating the Parking Brake
- 21 Operating the Throttle
- 21 Operating the Choke
- 21 Operating the Ignition Switch
- 22 Starting and Stopping the Engine
- 23 (PTO)
- 23 The Safety Interlock System
- 24 Driving Forward or Backward
- 25 Stopping the Machine
- 25 Adjusting the Height of Cut
- 26 Adjusting the Anti-Scalp Rollers
- 27 Positioning the Seat
- 27 Adjusting the Motion Control Levers
- 28 Pushing the Machine by Hand
- 28 Using the Side Discharge
- 29 Operating Tips
- 30 Maintenance
- 30 Recommended Maintenance Schedule(s)
- 32 Premaintenance Procedures
- 32 Raising the Seat
- 32 Lubrication
- 32 Greasing the Bearings
- 33 Engine Maintenance
- 33 Servicing the Air Cleaner
- 33 Servicing the Engine Oil
- 35 Servicing the Spark Plug
- 36 Cleaning the Cooling System
- 37 Fuel System Maintenance
- 37 Replacing the Fuel Filter
- 38 Electrical System Maintenance
- 38 Servicing the Battery
- 39 Servicing the Fuses
- 40 Drive System Maintenance
- 40 Checking the Tire Pressure
- 41 Hydraulic System Maintenance
- 41 Checking the Hydraulic Oil Level
- 43 Mower Deck Maintenance
- 43 Servicing the Cutting Blades
- 45 Mower Deck Leveling
- 47 Inspecting the Belts
- 47 Replacing the Mower Belt
- 48 Removing the Mower Deck
- 49 Installing the Mower Deck
- 49 Replacing the Grass Deflector
- 50 Cleaning
- 50 Washing the Underside of the Mower
- 51 Waste Disposal
- 51 Storage
- 51 Cleaning and Storage
- 53 Troubleshooting
- 55 Schematics