<b>Panel Controls and Terminals </b>. Yamaha CBX-D5, CBX-K1XG

Panel Controls and Terminals

■

Front Panel

w e o i u r y t

!0

o

SHIFT

PITCH

POWER ON @ OFF DC IN PHONES L– OUTPUT –R

ASSIGNABLE

MIN VOLUME MAX

SEQUENCER

STOP CONTINUE START TEMPO

PROGRAM

BANK

SELECT

PROGRAM

CHANGE

GM

ON

RESET

SOUND

OFF

XG

ON

MERGE

ON/OFF

SYSTEM

WHEEL ASSIGN

MIDI

CH

FIXED

VELOCITY RPN CONTROLLER NRPN

DRUM

NUMBER

TRANSPOSE

INPUT SUSTAIN

G E N E R A L

IN MIDI OUT TO HOST Mac PC-1 PC-2 MIDI

CONTROLLER NUMBER LIST

1 MODULATION

5 PORTA TIME

6 DATA ENTRY

7 VOLUME

10 PANPOT

11 EXPRESSION

65 PORTAMENTO

71 HARMONIC

72 RELEASE

73 ATTACK

74 BRIGHT

84 PORTA CTRL

91 REVERB

93 CHORUS

94 VARIATION

120 PB SENS

121 FINE TUNE

122 COARSE TUNE

123 VIBRT RATE

124 VIBRT DEPTH

125 VIBRT DELAY

126 FLT CUT FRQ

127 FLT RESO

128 EQ ATTACK

129 EG DECAY

130 EG RELEASE

142 CH PRESSURE

143 KEY PRESSURE

144 MSTR VOLUME

146 MSTR TUNE

147 VELOCITY

148 TEMPO

1 2 3 4 5 6 7 8 9

MIDI SOUND KEYBOARD CBX-K1XG

A B C D E F 0

ENTER

HEXA

DECIMAL DECIMAL

OCTAVE

OCTAVE SHIFT

OCTAVE

RESET q q

Keyboard

The CBX-K1XG has a 37-key, 3-octave keyboard (C2 to

C5), featuring initial touch (velocity) control. All note on, note off and velocity data is sent both to the internal tone generator and the connected MIDI device. When used with the C button, the keys are used for changing various settings and sending special MIDI messages. (See page

24.)

About the Functions of the CBX-K1XG: The functions are divided into two groups: Group A and Group B.

The Group A functions are shown on the panel, above the left section of the keyboard. The Group B functions are “hidden” and are listed on pages 32 – 33. Several functions can be used by pressing only the relevant key; in other words, pressing L is not necessary. These functions, such as Sequencer Stop and Start, are shown on the panel without underline. The right section of the keyboard serves as value entry and is used for those functions whose names are underlined on the panel and require value entry, such as Program Change and

Tempo. Functions whose names appear with a dashed underline on the panel (for example, GM ON and XG

ON) require pressing L . Value entry on the CBX-

K1XG can be done in two number systems: Decimal and Hexadecimal. The keys labeled A through F are for

Hexadecimal entry.

NOTE ■ The normal (default) velocity range of the

CBX-K1XG is from 16 to 127. The range differs according to the Touch Sensitivity setting (see page 32).

w

PITCH Wheel (Pitch Bend)

This spring-loaded Wheel controls Pitch Bend. The

Wheel’s operation can be reversed. (See page 32.) e

ASSIGNABLE Wheel

When the CBX-K1XG is turned on, this Wheel (with center detent) is set to control Modulation Depth of the internal tone generator and the connected MIDI device. It can be set to control other functions; see pages 18 and 30 for details. The Wheel’s operation can be reversed. (See page 32.) Turning the Wheel will momentarily show the currently assigned controller number on the LED.

r C

Button

This button is used to access the “hidden” functions of the

CBX-K1XG. Used with the N /

M buttons, it allows you to step up or down through program numbers. (See page 15.) Whenever turned on, the program number is set to 001 . Used with the keys of the keyboard, it allows you to access the sophisticated MIDI control functions. (See page 24.) t N

/

M

Buttons

These buttons are used to change the octave range of the keyboard, allowing you to play across the entire range of

MIDI notes (C-2 to G8). When the octave setting is modified, the current octave setting is momentarily displayed on the LED. (See page 17.) Press both of these buttons together to restore the normal octave setting (C2 to

C5).

5