advertisement
Config Menu
⇒
Codes
Code 7F
This parameter allows you to dictate how the printer will react when it receives a Hexadecimal code 7F. The default value depends on the emulation. (See the Emulation Parameter, presented earlier in this chapter.)
Ignore: The code is ignored.
Delete Char: The previous character is deleted.
Delete Buffer: The previous characters on the current print line are deleted.
Space:
Fill:
A Space character is substituted.
A Fill character is substituted.
Print 80 - 9F Hex
This parameter defines whether locations 80 through 9F Hex are to be treated as control characters or printable characters. The function of the control characters in this area depends on the emulation. The options are ON (printable characters) – the default, or OFF (control characters).
Ignore Char
This parameter allows you to select a character that will be ignored in the incoming data stream. Ignore Char functions in all emulations and nondownloadable print modes. It does not function in plot mode, font download, or VFU download. Options are 0-255, referring to the decimal value of any 8bit character, or OFF. Default is OFF.
Sub Char From
This parameter allows you to select a character that will be replaced by the character designated by the Sub Char To parameter. It functions in all emulations and non-downloadable print modes. It does not function in plot mode, font download, or VFU download. Default is OFF.
Sub Char To
This parameter allows you to select the character that will replace the character designated by Sub Char From. It functions in all emulations and nondownloadable print modes. It does not function in plot mode, font download, or VFU download. Default is OFF.
Chapter 3: Printer Menus and the Control Panel 3–57
advertisement
Related manuals
advertisement
Table of contents
- 9 Preface
- 9 Introduction
- 10 About This Manual
- 11 Chapter
- 11 Site Preparation
- 12 Figure 1 - 1. Shipping Screw Locations
- 12 Unpacking your printer
- 12 Repacking
- 12 Removing the Shipping Hardware
- 13 Figure 1 - 3. Rear view, showing Serial, Parallel and Power Plugs
- 13 Connecting the I/O
- 13 Interface Connections and Powering Up
- 13 Interface Connectors
- 14 Powering Up
- 14 Figure 1 - 4. Power plug and on/off switch
- 15 Figure 1 - 5. Inside the Lid
- 15 Paper System
- 15 Paper System Components
- 16 Print Gap
- 16 Paper Tension
- 16 Tractors
- 16 Figure 1 - 6. Left and Right Paper Tractors
- 17 Installing the Ribbon Cartridge
- 17 Figure 1 - 8. Installing the Ribbon Cartridge
- 17 Figure 1 - 7. Ribbon Cartridge
- 18 Figure 1 - 9. Ribbon Shield Panels
- 19 Figure 1 - 10. Control Panel
- 19 LED Indicators
- 19 LCD (Liquid Crystal Display)
- 19 Control Panel Components
- 21 Chapter
- 21 Introduction
- 22 Loading Paper for Standard Printing Mode
- 22 Figure 2 - 1. Inside Paper Inlet, visible when looking inside the printer cabinet
- 22 Figure 2 - 2. Paper path past the lid
- 23 Figure 2 - 4. Column Alignment Scale
- 23 Figure 2 - 5. Horizontal Vernier Wheel
- 24 Figure 2 - 6. Top of Form Nubbin
- 25 Print Gap Adjustment
- 25 Gap Zone
- 25 Print Gap Profile Mode
- 25 Creating a Gap Zone Profile
- 26 Using a Saved Gap Zone Profile
- 26 Fine-tuning the Automatic Print Gap Setting
- 27 Set Print Gap Detect Mode to Manual
- 27 Figure 2 - 7. Typical Display when Print Gap Mode is set to “Auto
- 28 Setting Up Configurations
- 28 Figure 2 - 8. Typical display when adjusting Print Gap
- 29 Chapter
- 29 Introduction
- 29 Control Panel Display
- 30 The Display During Normal Operation
- 30 Figure 3 - 1. Control Panel Display for Normal Operation
- 30 Current State
- 30 Current Configuration
- 30 Paper Weight & Hammer Impact
- 31 The Display When In A Menu
- 31 Figure 3 - 2. Control Panel Display for Menus
- 31 Table 3 - 1 Paper Weight & Hammer Impact Indicator
- 32 Control Panel Key Functions
- 32 Online Key
- 32 LF Key (Line Feed)
- 32 FF Key (Form Feed)
- 32 Figure 3 - 3. Control Panel
- 33 FF Key (Form Feed) continued
- 33 TOF Key (Top of Form)
- 33 View Key
- 33 PRINT GAP + and - Keys
- 33 Up and Down Arrow Keys
- 33 Menu Key
- 34 Enter Key
- 34 Clear Key
- 35 Clear Key continued
- 35 Config Key
- 36 Control Panel Menus
- 36 Categories, Parameters and Selections
- 36 Using Menus
- 38 Example: Changing Form Length Using the Menu System
- 39 How to Print a Control Panel Selected Options Report
- 40 Operator Menu
- 40 Font Category
- 40 Ser/Par Language
- 41 Ser/Par Character Set
- 41 Matrix
- 41 OCRA Density
- 42 Ser/Par Style
- 42 CPI (Characters Per Inch)
- 42 Panel Language
- 42 OCR Standards
- 42 Compressed
- 43 Forms Category
- 43 Length (lines)
- 43 Length (inches)
- 43 LPI (Lines Per Inch)
- 43 Top Margin
- 43 Bottom Margin
- 44 Left Margin
- 44 Right Margin
- 44 Horz Adjust
- 44 Vert Adjust
- 44 Print to EOF (End Of Form)
- 45 Print to EOF (End Of Form) Continued
- 45 Quick Access
- 45 Eject Distance
- 46 Eject Delay
- 46 Impact
- 46 Paper Weight
- 46 Fast Slew
- 46 Double Strike
- 46 RibbonMonitor
- 47 RibnMon Thresh
- 48 Perf Skip
- 48 Print Gap Category
- 48 Detect
- 48 Adjust
- 49 Reset
- 50 Creating a Gap Zone Profile
- 50 Detect Distance
- 51 VFU Category (Vertical Format Units)
- 51 VFU Enable
- 51 VT Channel (Vertical Tab Channel)
- 51 Skip When
- 52 Config Menu
- 52 Printer Category
- 52 Powerup
- 52 Ser/Par Emulation
- 52 LAN Emulation (LAN Interface only)
- 52 Dump Mode
- 53 IO Hold
- 53 Report
- 54 Beeper Mode
- 54 Beeper Volume
- 55 Codes Category
- 55 Auto LF (Line Feed)
- 55 Auto CR (Carriage Return)
- 55 Line Wrap
- 55 Wrap Line Feed
- 56 Print on CR
- 56 Form Feed at TOF
- 56 Alt ESC (Alternate Escape)
- 56 Upper Only
- 57 Code 7F
- 57 Print 80 - 9F Hex
- 57 Ignore Char
- 57 Sub Char From
- 57 Sub Char To
- 58 Configurations Category
- 58 Powerup Config
- 58 Config n Label - (where n = 1 to 10)
- 60 Serial I/O Category
- 60 Data Bits
- 60 Stop Bits
- 60 Parity
- 60 8th Bit
- 60 Protocol
- 61 Status Enquiry
- 61 DTR Function
- 62 DTR Function continued
- 62 DTR Polarity
- 62 Busy Polarity
- 62 RTS Function
- 62 Robust Xon
- 63 Parallel I/O Category
- 63 POPC (Print On Paper Command)
- 63 8th Bit
- 63 Bi-Directional
- 64 Intellifilter Category
- 64 Serial
- 64 Parallel
- 64 Twinax/Coax
- 64 File Management
- 65 TCP/IP Menu (LAN Interface Only)
- 65 IP Addr Category
- 65 Gateway Category
- 66 Subnet Category
- 67 Test Menu
- 67 Pattern Category
- 67 Print
- 68 Fault Override Category
- 68 Paper Motion
- 68 Diag Category
- 68 Cal-Paper (Calibrate Paper Out)
- 69 Help Menu
- 69 Figure 3 - 5. Control Panel Navigation
- 71 Appendix A: Troubleshooting
- 71 Introduction
- 71 Messages
- 71 Faults
- 71 Fault Correction Procedure
- 72 Table A - 1. Display Messages
- 76 Table A - 2. Paper/Printing Corrective Action
- 77 Appendix B: Specifications
- 77 Industry and Agency Standards
- 77 Electro-Magnetic Emissions
- 77 Electro-Magnetic Immunity
- 77 Energy Conservation
- 77 Safety
- 77 Acoustic
- 77 Marking
- 78 Physical Configurations
- 78 Weight
- 78 Dimensions
- 78 Preventive Maintenance
- 78 Environment
- 78 Operating
- 78 Nonoperating
- 78 Safety
- 79 Cooling System
- 79 Acoustics
- 79 Power Supply
- 79 Heat Load Contribution
- 80 Emulations
- 80 Characters Per Inch
- 80 Lines Per Inch
- 80 Type Styles
- 80 Draft and Data Processing
- 80 Gothic and Courier
- 80 OCR–A and OCR–B
- 80 Large Character Printing
- 81 Standard Languages and Character Sets
- 82 Nonvolatile Memory
- 82 Paper Description
- 82 Paper Movement Speed
- 82 Throughput