- No category
advertisement
The Non-Active Menu
2. Test Sub-Menu “
” (1 of 4)
The Test Sub-Menu allows the operator to test some of the machine’s components.
How to Access the Test Sub-Menu
1. Enter the Non-Active menu (refer to the
Entering the Non-Active Menu
section).
2. Press the ▲ or ▼ keypads to scroll through the
Non-Active Menu’s sub-menus until “ ” appears in the display.
3. Press the keypad. “ ” appears in the display.
4. Press the ▲ or ▼ keypads to scroll through the
Test Sub-Menu’s options.
5. Press the keypad to access the desired Test
Sub-Menu’s option. Refer to the
Using the Test
Sub-Menu’s Options
section for details on each option.
Using the Test Sub-Menu’s Options
a. Water Level Test “ ”
NOTE: Make sure all water has been drained from the machine.
i.
Press the keypad. “ XX.X
”, which is the measured water level, appears in the display and flashes.
ii.
Press the keypad. “ XX.X
”, which is the water level to be measured, appears in the display. iii. Note the number shown in the display and mark the middle of the door glass.
iv. Press the keypad. “ .” appears in the display and the machine begins to fill with water.
v.
Fill the machine to the mark made on the middle of the door glass. Press the ▼ keypad to turn off the water and the
▲ keypad to turn on the water as needed.
vi. Press the keypad. “ XX.X
”, which is the current water level, appears in the display and flashes.
vii. Compare the number shown in the display to the number that was recorded earlier. If necessary, press the ▲ or ▼ keypads to change the number shown in the display until it matches the number that was recorded earlier.
viii. Press the keypad. “ XX.X
”, which is the measured water level, is shown in the display.
ix. Press the keypad. “ ” appears in the display.
b. Water Inlet Test “ ” i.
Press the keypad. “ ” appears in the display.
ii.
Press the
▲ or
▼ keypads to scroll through the inlets until the desired inlet is shown in the display. Refer to
Table 3
.
Display
“ ”
“ ”
“ ”
“
”
“ ”
“ ”
“ ”
Hot water 1
Hot water 2
Hot water 3
Cold water 1
Cold water 2
Cold water 3
Description
Direct (optional)
Table 3 iii. Press the keypad to turn on the desired inlet. The display shows a dot next to the inlet number (e.g., “ .”).
iv. Press the keypad to turn off the desired inlet.
v.
Press the keypad. “
” appears in the display.
(continued)
16 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT D1350
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 12 Start Up
- 12 Start Mode
- 12 Run Mode
- 12 Stop Mode
- 12 End of Cycle Mode
- 13 What is Available in the Non-Active Menu?
- 13 Entering the Non-Active Menu
- 13 Non-Active Menu Navigation
- 14 Non-Active Menu Options
- 15 Non-Active Menu Flowchart
- 17 Information Sub-Menu Flowchart
- 18 ” (1 of 4)
- 19 Test Sub-Menu Flowchart (1 of 4)
- 20 ” (2 of 4)
- 21 Test Sub-Menu Flowchart (2 of 4)
- 22 ” (3 of 4)
- 23 Test Sub-Menu Flowchart (3 of 4)
- 24 ” (4 of 4)
- 25 Test Sub-Menu Flowchart (4 of 4)
- 27 Entry Code Set Sub-Menu Flowchart
- 29 Clock Set Sub-Menu Flowchart
- 31 Network Address Sub-Menu Flowchart
- 33 Rapid Advance Enable Sub-Menu Flowchart
- 35 Temperature Indication Enable Sub-Menu Flowchart
- 36 ” (1 of 3)
- 37 MMC Sub-Menu Flowchart (1 of 3)
- 38 ” (2 of 3)
- 39 MMC Sub-Menu Flowchart (2 of 3)
- 40 ” (3 of 3)
- 41 MMC Sub-Menu Flowchart (3 of 3)
- 43 Prices Sub-Menu Flowchart
- 45 Service Counters Sub-Menu Flowchart
- 47 Weekly Cycle Count Sub-Menu Flowchart
- 49 Last Errors Sub-Menu Flowchart
- 51 Out of Order Sub-Menu Flowchart
- 52 Error Messages
- 55 Events
- 57 Infra-red Communications