advertisement
▼
Scroll to page 2
of
130
ASCII Character Chart
APPENDIX D:ASCII CHARACTER CHART
Corresponding ASCII on printer (Options [70]/[170]/[270]) Hex Character
Code Character
42
43
44
45
37
38
39
41
46
47
48
33
34
35
36
20
30
31
32
B
C
D
E
7
8
9
A
F
G
H
5
6
3
4
1
2
Space
0
Code Character
55
56
57
58
51
52
53
54
4D
4E
4F
50
49
4A
4B
4C
59
5A
5C
U
V
W
X
S
T
Q
R
\
Y
Z
M
N
O
P
I
J
K
L
C
117
advertisement
Related manuals
advertisement
Table of contents
- 2 Note to Installers
- 2 System Failures
- 2 International Warranty
- 2 Warranty Procedure
- 2 Conditions to Void Warranty
- 2 Items Not Covered by Warranty
- 2 Disclaimer of Warranties
- 2 Installer’s Lockout
- 2 Out of Warranty Repairs
- 4 GENERAL DESCRIPTION of the EQUIPMENT and CLASSIFICATION.
- 4 CLASSIFICATION
- 4 IMPORTANT:
- 4 CAUTION:
- 5 Introduction
- 6 System Overview
- 6 SG-DRL3/SG-DRL3E/SG-DRL3-2L
- 7 SG-DRL3-IP
- 7 Approvals
- 7 Industry Approvals
- 9 Parallel Printers
- 9 Serial Printers
- 9 UL Manual Mode
- 9 Description (Hardware)
- 10 SG-BP3 Backplane
- 10 SG-PSU3 Power Supply Unit
- 10 Electrical Specifications:
- 10 SG-CPM3 Central Processing Module
- 10 Line Cards
- 11 SG-BP3X Interface Module (One required per rack if SG-DRL3, SG-DRL3E, or DRL3-2L are used)
- 15 Receiver Setup and Operation
- 16 Description (Operation)
- 16 Operation with Default Programming
- 17 Virtual Connectivity
- 17 Status Addressing
- 17 Automation Input/Output (Port 1025)
- 17 Compatibility
- 17 Automation Protocols
- 17 Data Byte Protocol
- 17 Acknowledgment of the Signal
- 17 COM Responses
- 18 Automation Absent
- 18 SG-System III SIA Internal Status Output
- 19 SG-CPM3 Operating Modes
- 20 Contrast Adjust
- 20 Active Mode
- 20 Manual Mode
- 21 Standby Mode
- 21 System Trouble and System Information
- 21 AHS Table Management
- 22 Line Card
- 23 Standby Mode
- 23 SG-DRL3
- 23 SG-DRL3E
- 24 SG-DRL3-2L
- 25 SG-DRL3-IP
- 25 Line Fault
- 25 SG-CPM3 Error
- 25 SG-DRL3/SG-DRL3E/SG-DRL3-2L Data Reception
- 25 Fault Data Message
- 26 Ethernet Interface
- 26 Supervised Receiver Database
- 28 Introduction
- 28 Console Software
- 28 Debug
- 28 Debug Cable Connectivity
- 28 Debug Setup
- 29 Manual Programming
- 30 System Functions
- 30 SG-CPM3 Options
- 27 Programming/ Operation
- 45 Advanced Programming
- 48 SG-DRL3-2L/DRL3E System Options
- 50 SG-DRL3/SG-DRL3-2L Static Options
- 61 SG-DRL3/SG-DRl3-2L Dynamic Options
- 91 SG-DRL3-IP Programming
- 92 Options: 00 - 47
- 99 Printer Words
- 104 Telco Connector Pin Outs
- 106 DEC-HEX-BIN
- 106 Conversion Chart
- 108 ASCII Character Chart
- 110 Communication Formats
- 113 Serial Printer Port (COM2)
- 113 RS-232 Serial Automation
- 112 Ports
- 114 Events & Messages
- 123 Glossary