System Controller Alphabetical Command Reference. Sun Microsystems Fire 6800, Fire 4800, Fire 4810, Fire 3800
Anúncio
Anúncio
C H A P T E R
2
System Controller Alphabetical
Command Reference
This chapter describes system controller command line interface, command syntax, and command arguments. It provides, in tabular form, a summary of all of the system controller commands. It also provides complete descriptions and examples for each system controller command.
System Controller Syntax, Command
Names, Command Arguments, and
Comments
Command Syntax
The general syntax of system controller commands is: command_name [option flags] [ arguments ]
Note – The system controller commands can be partially typed if what is typed is enough to make the command unique.
17
Command Names
Most system controller commands are in the form of verbnoun. Command names are in the English language. System controller commands are case insensitive.
Command Arguments
■
■
■
■
Some system controller commands have arguments and some system controller commands do not have arguments. Depending on the command, some arguments are followed by flags and others are not. A few examples include: help help -v showboards sb0 showboards -v sb0
Device Names
shows the device names that can be managed in the platform shell. You can type the device names in either upper case or lower case in both
and
Note – The devices in
and
depend on the system you have. For example, only the Sun Fire 6800 system can have six power supplies and six
CPU/Memory boards. In a domain, you can manage devices only if they are assigned to a domain.
TABLE 2-1 Devices That Can Be Managed in the Platform Shell
Device Description
Power grids
Power supplies
CPU/Memory boards
I/O assemblies
Repeater boards
Fan trays
System controller
Device Name
GRID0, GRID1
PS0, PS1, PS2, PS3, PS4, PS5
SB0, SB1, SB2, SB3, SB4, SB5
IB6, IB7, IB8, IB9
RP0, RP1, RP2, RP3
FT0, FT1, FT2, FT3
SC0, SC1
18 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
shows the devices that can be managed in a domain.
TABLE 2-2 Devices That Can Be Managed in a Domain
Device Description
CPU/Memory boards
I/O Assemblies
Device Name
SB0, SB1, SB2, SB3, SB4, SB5
IB6, IB7, IB8, IB9
Board States
lists the board states. These board states are displayed by the showboards command. For some commands, such as addboard and deleteboard , you need to determine the board state with showboards before you can execute the addboard or deleteboard command.
TABLE 2-3
Board States
Available
Assigned
Active
Board States
Description
The board is not assigned to any domain.
The board belongs to a domain, but the hardware has not been configured or it is not in use.
The board is being actively used by the domain to which it has been assigned. You cannot reassign an active board.
To determine the board state, use the showboards command and look under the
State header.
Chapter 2 System Controller Alphabetical Command Reference 19
Status
describes the Status field displayed in the showboards command.
TABLE 2-4 Status Field Displayed in the showboards Command
Test Status
Passed
Failed
OK
Under Test
Not Tested
Degraded
-
Description
All board components passed testing.
The board failed testing and is not usable. This could also indicate corrupt or incompatible firmware.
The component is functioning properly (power supply, fan tray, or
Repeater board).
The domain is running POST (power-on self-test).
The board is not been tested.
Certain components on the board have failed or are disabled. A board is in degraded mode when there are still usable parts on the board.
The slot is empty or not applicable for this device.
Comments
You can separate system controller commands with a semicolon (;) on the same line.
For example: schostname : SC> addboard -d a sb2;deleteboard sb3
In the previous example, both the addboard and deleteboard commands are executed.
A pound sign ( # ) signifies the start of a comment on the current line. For example: schostname : SC> addboard -d a sb2 #this text is ignored
In the previous example, the addboard command is executed. Everything you type after the # and before pressing the Return key is ignored.
20 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
If you type the following line, board sb2 is added to domain A and the deleteboard command is not executed.
schostname : SC> addboard -d a sb2 # deleteboard sb2
Another example of the pound sign (#) signifying the start of a comment at the beginning of a command line is: schostname : SC> # this text is ignored
Clearing an Entry
You use the dash ( - ) to clear the entry in a command.
System Controller Command Summary
lists and describes the system controller commands and how you can access them. Many commands are accessible from both the platform shell and the domain shell. The system controller commands may differ in how they are used, the effect of the command, and the scope of the command between the platform and domain shells.
Command
TABLE 2-5 System Controller Command Summary
Description
Assigns a board to a domain.
Sends a Break signal to the domain.
Displays connections to the system controller or to a domain.
Connects to a domain from the platform shell.
Unassigns a board or a slot from a domain.
Adds a component to the blacklist.
Disconnects the current specified connection.
x x x x x
Platform Shell x x x x
Domain Shell x x x
Chapter 2 System Controller Alphabetical Command Reference 21
Command
TABLE 2-5 System Controller Command Summary (Continued)
Description
Saves the system controller configuration to a server.
Deletes a component from the blacklist.
Updates the flash PROMs on CPU/Memory boards, I/O assemblies, and the System
Controller boards.
Provides basic help information for system controller commands.
Shows the command history with date and time stamps.
Sets the shell password. There are separate passwords for the platform connection and each domain connection.
Powers off components.
Powers on components.
Reboots the system controller.
Resets the domain in the domain shell or the other system controller in the platform shell.
Restores the system controller configuration from a server.
Exits the domain shell and resumes access to the domain console.
Sets the time, date, and time zone for the platform and each domain.
Resets the system controller to the default values.
Changes the keyswitch position.
Configures domain specific variables.
Configures platform specific variables.
Shows status, assignment, and board information for boards in the system.
Displays detailed information about a component.
Displays the time, date, and the timezone for the platform or for domains.
x x
Platform Shell x x x x x x x x x x x x x x x x
Domain Shell x x x x x x x x x x x x x x x
22 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
Command
TABLE 2-5 System Controller Command Summary (Continued)
Description
Displays the configuration and status of the domain.
Displays the current environmental status, temperatures, currents, and voltages.
Displays the virtual keyswitch setting.
Displays the logs.
Displays the configuration of the platform, the status of a domain, and SNMP information.
Displays the system controller uptime and version.
Tests the CPU/Memory board you specify at the command line.
Platform Shell x x x x x x x x x
Domain Shell x x
Status
describes the Status field displayed in the showboards command.
TABLE 2-6 Status Field Displayed in the showboards Command
Test Status
Passed
Failed
OK
Under Test
Not Tested
– (dash)
Degraded
Description
All board components passed tests.
A component fails when there are no usable parts on the board.
The component is functioning properly (power supply, fan tray, or
Repeater board).
The domain is running POST (power-on self-test).
No testing has been done.
The slot is empty or disabled. Not applicable for this device.
Certain components on the board have failed or are in the blacklist.
A board is in degraded mode when there are still usable parts on the board.
Chapter 2 System Controller Alphabetical Command Reference 23
Domain States
■
■
■
■
■
■
In the showplatform and showdomain commands, one of the fields in the command output is domain status. The major values of domain status are:
Active-Solaris
Active-OpenBoot PROM
Active-Booting
Running POST
Standby
Powered off
24 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
Alphabetical Listing of System
Controller Commands
The following sections describe the system controller commands.
addboard
Assigns a board or a slot to a domain.
Scope platform shell, domain shell
Syntax addboard -d domainID system_board_name [ system_board_name . . .
] addboard -h
Options/Parameters
-h displays help for this command.
system_board_name is the board to be added. Possible values for system_board_name are sb0 – sb5 (CPU/Memory board) or ib6 ib9 (I/O assembly).
-d domainID is the domain where the board will be added. The domainID is a, b, c, or d.
Chapter 2 System Controller Alphabetical Command Reference 25
Description
Assigns system_board_name to the specified domain within the platform shell or to the current domain. The board state must be Available. To display the board states, use the showboards
command. For more information on board states, see “Board
In order to assign a board to a domain, the board name must be listed in the Access
Control List (ACL) for domain shells. When a board is listed in the ACL, the system controller software is allowed to process addboard requests on that board.
The Access Control List (ACL) is ignored in the platform shell. The platform shell always has permission to add or delete boards. Even if a board is not in the domain’s ACL, when you type the addboard command from the platform shell, this overrides the ACL.
If a board is not present, the command assigns ownership of the slot to the specified domain.
See Also
deleteboard, setupplatform, showboards ,
and Sun Fire 6800/4810/4800/3800 Systems Platform Administration Manual (for a stepby-step procedure on assigning boards to a domain).
Example—Platform Shell
To add board name sb2 to domain A, type:
CODE EXAMPLE 2-1 addboard Example in the Platform Shell schostname : SC> addboard -d a sb2
Although a message is sent to the Solaris operating environment about a new board being added, there is not a client in the Solaris operating environment that reads these messages. Therefore, these messages will not be seem by the Solaris operating environment.
26 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
Example—Domain Shell
To add board name sb2 to the current domain, type:
CODE EXAMPLE 2-2 addboard Example in the Domain Shell schostname : A> addboard sb2
If you cannot assign a board to a domain in the domain shell, this is most likely because the board is not listed in the ACL. See the “Description“ section for more information. Another possibility is that the domain is currently in use. An error message will tell you the reason why you can not perform the operation.
Chapter 2 System Controller Alphabetical Command Reference 27
break
Sends a break signal to the domain console.
Scope domain shell
Syntax break [-y|-n] break -h
Options/Parameters
-h displays help for this command.
-y answers yes to the warning message. Does not prompt for confirmation.
-n answers no to the warning message. Does not execute this command if confirmation is requested.
Description
Sends a Break signal to the domain console.
Note – This command pauses the Solaris operating environment.
When the Solaris operating environment is running in the domain, the usual effect of the break signal is to force entry into OpenBoot PROM or the debugger. The Solaris operating environment will ignore the break signal if the keyswitch is set to secure.
See Also
28 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
Example
shows using the break command to pause the Solaris operating environment and enter the OpenBoot PROM.
CODE EXAMPLE 2-3 break Command Example in the Domain Shell schostname : A> break ok
Chapter 2 System Controller Alphabetical Command Reference 29
connections
Displays connections to the system controller or a domain.
Scope platform shell, domain shell
Syntax for the Platform Shell connections [-d domainID ] connections -h
Syntax for the Domain Shell connections [-h]
Options/Parameters
-h displays help for this command .
-d domainID shows connections to the specified domain (a, b, c, or d).
Description
Displays hosts currently connected to the system controller. The platform shell shows the connections to the platform shell and to each domain shell (or to the specified domain). The domain shell displays the information shown in
CODE EXAMPLE 2-4 , which is described in TABLE 2-7 .
See Also
30 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
Example—Platform Shell
CODE EXAMPLE 2-4 connections Command for the Platform Shell schostname : SC> connections
ID Hostname
--
1
2
--------
XXXXXXX
XXX
Idle
----
-
-
Connected on
------------
Jan 01 00:00
Jan 01 00:21
Connected to
------------
Platform
A
describes the headers in the output for
.
TABLE 2-7 Header Description for
Header Column in
ID
Hostname
Idle
Connected on
Connected to
Description
Connection ID. This is a unique number. Use this number to disconnect a specific session.
Source of the connection for this session. If the value is localhost , the connection was established through the platform.
Amount of time the session is sitting without any activity. Displays a dash ( - ) if the session is active.
Date and time the connection was initiated. The format is
Mon dd hh:mm.
Shell or console this session is connected to. Possible values are
Platform or domainIDs a, b, c, or d.
Chapter 2 System Controller Alphabetical Command Reference 31
console
Connects to a domain from the platform.
Scope platform shell
Syntax console [-d] domainID console -h
Options/Parameters
-h displays help for this command.
[-d] domainID is the domain to connect to and is a , b , c , or d . The d parameter is optional and does not need to precede the domainID.
Description
Opens a domain connection. You use the console command to navigate from the platform to a domain. If a password was created for connecting to this domain, you must enter the password.
See Also
32 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
Examples—Platform Shell
When there is no password initialized for this domain:
CODE EXAMPLE 2-5 console Example With the -d Option and No Password Assigned
Accessing Domain B schostname : SC> console -d b
Connected to Domain B
Domain Shell for Domain B schostname : B>
When there is no password initialized for this domain, you could also type:
CODE EXAMPLE 2-6 console Example Without the -d Option and No Password
Assigned Accessing Domain B schostname : SC> console b
Connected to Domain B
Domain Shell for Domain B schostname : B>
When a password is set for this domain:
CODE EXAMPLE 2-7 console Example With the -d Option and A Password Assigned
Accessing Domain A schostname : SC> console -d a
Password:
Permission Granted
Connected to Domain A
Domain Shell for Domain A schostname : A>
Chapter 2 System Controller Alphabetical Command Reference 33
When a password is set for this domain, you could also type:
CODE EXAMPLE 2-8 console Example Without the -d Option and A Password Assigned
Accessing Domain A schostname : SC> console a
Password:
Permission Granted
Connected to Domain A schostname : A>
34 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
deleteboard
Unassigns a board or a slot from the domain where it is currently assigned.
Scope platform shell, domain shell
Syntax for the Platform Shell and the Domain Shell deleteboard system_board_name [ system_board_name . . .] deleteboard [-h]
Options/Parameters
-h displays help for this command.
system_board_name is the board to be deleted. Values are sb0 to sb5 ( CPU/Memory board) and ib6 to ib9 (I/O assembly).
Description
Unassigns a board from the domain where it is currently assigned. The
CPU/Memory board or the I/O assembly board status must be in the Assigned state.
The board name must be listed in the Access Control List (ACL) for domain shell from which you want to unassign the board.
Type the showboards command to display the board state. A slot does not need to be occupied with a board before you can unassign it from a domain.
See Also
,
, and the Sun Fire 6800/4810/4800/3800 Systems Platform Administration Manual (for step-bystep procedure on unassigning boards from a domain).
Chapter 2 System Controller Alphabetical Command Reference 35
Example—Platform Shell
To delete I/O assembly ib7 , type:
CODE EXAMPLE 2-9 deleteboar d Example Showing Deleting I/O Assembly 7 schostname : SC> deleteboard ib7
The platform shell always has permission to add or delete boards.
Example—Domain Shell
To delete CPU/Memory board sb3 from the current domain, domain A, type:
CODE EXAMPLE 2-10 deleteboar d Example Showing Deleting CPU/Memory Board 3 schostname : A> deleteboard sb3
The domain shell can delete boards only from the current domain.
36 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
disablecomponent
Adds a component to the blacklist.
Scope platform shell, domain shell
Syntax disablecomponent component_name [ component_name . . .
] disablecomponent -h
Options/Parameters
-h displays help for this command.
■
■
■
component_name is (see
and
system_ board_name /port/physical_bank/logical_bank for the CPU/Memory board system_ board_name /port/bus for an I/O assembly system_ board_name /card for an I/O assembly
Note – You can use partial component names.
Chapter 2 System Controller Alphabetical Command Reference 37
TABLE 2-8 component_name Descriptions for the CPU/Memory Board Used in the disablecomponent Command
Board or Device
CPU system
CPU/Memory boards
( system_ board_name)
Ports on the
CPU/Memory board
Physical memory banks on
CPU/Memory boards
Logical banks on
CPU/Memory boards
Component Name
board_name/port/p hysical_bank/logical_bank
SB0, SB1, SB2, SB3, SB4, SB5
P0, P1, P2, P3
B0, B1
L0, L1, L2, L3
TABLE 2-9 component_name Descriptions for the I/O Assembly Used in the disablecomponent Command
Board or Device
I/O assembly system
I/O assemblies
( system_ board_name)
Ports on the I/O assembly
Buses on the I/O assembly
I/O cards in the I/O assembly
Component Name
board_name/port/bus or board_name/card
IB6, IB7, IB8, IB9
P0, P1
B0, B1
C0, C1, C2, C3, C4, C5, C6, C7—the number of cards varies with the
I/O assembly
38 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
Description
This command adds a component to the blacklist. Blacklisting provides a list of system board components that will not be tested and will not be configured into the domain when you change the domain’s keyswitch from an inactive state to an active state or when the domain is rebooted.
The blacklists are stored in non-volatile memory. Blacklist a component or device if you believe it may be failing intermittently.
■
■
■
■
■
Devices can be the following (see
and
CPU ports (CPU processors)
Physical and logical memory banks
I/O ports
I/O buses
I/O cards
The platform shell blacklists supersede the domain shell blacklists. For example, if a component is disabled in the platform shell, it will always be disabled in all domains.
Blacklisting from the platform shell applies to all domains. Blacklisting in a domain applies only to the current domain. If you disable a component in a domain and then move the component to another domain, the component is not disabled.
See Also
enablecomponent, showcomponent
, and the Sun Fire 6800/4810/4800/3800
Systems Platform Administration Manual (for step-by-step procedure on adding a component to the blacklist).
Chapter 2 System Controller Alphabetical Command Reference 39
Examples
This example of the disablecomponent command adds system_board_name sb4 to the blacklist.
CODE EXAMPLE 2-11 disablecomponent Command Example Adding sb4 to the
Blacklists schostname : A> disablecomponent sb4
This example of the disablecomponent command adds system_board_name sb0 and CPU port 3 to the blacklist. Note that any memory banks on this CPU processor port are unreachable and are implicitly disabled.
CODE EXAMPLE 2-12 disablecomponent Command Example Adding sb0 CPU Port 3 to the Blacklist schostname : A> disablecomponent sb0/p3
This example of the disablecomponent command adds system_board_name sb2,
CPU processor port 3, physical bank 0 to the blacklists. Note that any logical banks belonging to this physical bank are disabled.
CODE EXAMPLE 2-13 disablecomponent Command Example Adding sb2, CPU Port 3, and Physical Bank 0 to the Blacklists schostname : A> disablecomponent sb2/p3/b0
This example of the disablecomponent command adds system_board_name ib9, port 0, bus 1 and board_name ib8, I/O card 2 to the blacklists. Disabling I/O card 2 shuts down the power to that I/O card.
CODE EXAMPLE 2-14 disablecomponent Command Example Adding I/O Assembly 9,
Port 0 and Bus 1 and Also I/O Assembly 8, I/O Card 2 to the
Blacklists schostname : A> disablecomponent ib9/p0/b1 ib8/c2
40 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
disconnect
Disconnects the current or specified connection.
Scope platform shell, domain shell
Syntax for the Platform Shell disconnect [ ID ] disconnect -h
Syntax for the Domain Shell disconnect [-h]
Options/Parameters
-h displays help for this command.
ID (platform shell only) is the connection to be terminated. ID is the number displayed under the heading ID for the connections command.
Description
Terminates a connection to the system controller. If this command is used with no arguments, it disconnects the current session. For illustrations of the disconnect command, see
in “System Controller Navigation” on page 10.
If the connection was initiated from another system, you will be returned to the remote host. If the session was initiated from the platform shell, this command displays the platform shell prompt. If you are connected from the serial port, then you will return to the main menu.
See Also
Chapter 2 System Controller Alphabetical Command Reference 41
Examples
To disconnect a session from the system controller platform shell with a telnet connection (
CODE EXAMPLE 2-15 Disconnecting a Session From the System Controller Platform Shell schostname : SC> disconnect
Connection closed by foreign host.
If you are connected to the system controller platform console with the serial connection, you will see the following after typing disconnect :
CODE EXAMPLE 2-16 Disconnecting a Session From the System Controller Platform
Console schostname : SC> disconnect
Type 0 for Platform Shell
Type 1 for domain A
Type 2 for domain B
Type 3 for domain C
Type 4 for domain D
Input:
To disconnect a session from a system controller domain shell, type:
CODE EXAMPLE 2-17 disconnect Example Showing Disconnecting a Session From the
Domain A Shell schostname : A> disconnect
Connection closed by foreign host.
Note – When you disconnect from a domain shell, you will obtain the parent shell prompt (either the remote host prompt or the platform shell prompt).
42 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
dumpconfig
Saves the platform and domain configurations to a server.
Scope platform shell
Syntax dumpconfig -f url dumpconfig -h
Options/Parameters
-h displays help for this command.
-f specifies the URL, which can only be ftp . For example: ftp:// userid : password @ host / path ftp:// host / path
Note – The hostname you enter must be a complete host name (not a partial one).
Note – The directory specified in the URL path must have write permission, including user access. Also, make sure that the data files are present in the URL.
Chapter 2 System Controller Alphabetical Command Reference 43
Description
Use this command after you complete the initial configuration of the platform and the domains. This command saves the system controller configuration to a server.
The data files include schostname .nvci
and schostname.
tod .
Caution – Run this command when you change platform or domain configurations.
For more information, see the following bulleted list of system controller commands that change the configuration. Also, run this command whenever you change the hardware configuration.
Invoking this command is very important because if the System Controller board fails and you did not use this command to save the platform and domain configurations, you will have to manually reconfigure the platform and the domains.
■
■
■
■
■
■
■
■
■
Run the dumpconfig command again after configuration changes are made to the system controller, for example with the following system controller commands: setupdomain setupplatform setdate addboard deleteboard enablecomponent disablecomponent password setkeyswitch or whenever you change the hardware configuration. By running again this command, the new platform and domain configurations are saved to a server.
This command is intended to be used as part of the procedure in replacing a failed
System Controller board. You should not use this command to revert to an old configuration. The showplatform , showdomain , and showboards system controller commands display all of the configuration and can be used as a reference.
If you need to replace the System Controller board, this configuration information can be used to restore the platform and domain configurations to the replacement
System Controller board.
See Also restoreconfig
44 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
Example
TABLE 2-10 dumpconfig Example schostname : SC> dumpconfig -f ftp:// hostname / path_name
Created: ftp:// host / path_name/schostname.
nvci
Created: ftp:// host / path_name/schostname.
tod
Chapter 2 System Controller Alphabetical Command Reference 45
enablecomponent
Deletes a component from the blacklist.
Scope platform shell, domain shell
Syntax enablecomponent component_name [ component_name . . .
] enablecomponent -h
Options/Parameters
-h displays help for this command.
■
■
■
component_name is (
and
system_board_name/port/physical_bank/logical_bank for CPU/Memory boards
system_board_name/port/bus for an I/O assembly system_ board_name /card for an I/O assembly
TABLE 2-11 component_name Descriptions for the CPU/Memory Board Used in the enablecomponent Command
Board or Device
CPU system
CPU/Memory boards
( system_ board_name)
Ports on the
CPU/Memory board
Physical memory banks on
CPU/Memory boards
Logical banks on
CPU/Memory boards
Component Name
board_name/port/p hysical_bank/logical_bank
SB0, SB1, SB2, SB3, SB4, SB5
P0, P1 ,P2, P3
B0, B1
L0, L1, L2, L3
46 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
TABLE 2-12 component_name Descriptions for the I/O Assembly Used in the enablecomponent Command
Board or Device
I/O assembly system
I/O assemblies
( system_ board_name)
Ports on the I/O assembly
Buses on the I/O assembly
I/O cards in the I/O assembly
Component Name
board_name/port/bus or board_name/card
IB6, IB7, IB8, IB9
P0, P1
B0, B1
C0, C1, C2, C3, C4, C5, C6, C7—the number of cards varies with the
I/O assembly
Description
Removes a component from the blacklist. Blacklisting provides a list of system board components that will not be tested and will not be configured into the domain when you change the keyswitch setting from an inactive state to an active state or when the domain is rebooted. The blacklists are stored in non-volatile memory.
■
■
■
■
■
Components can be the following:
CPU ports (CPU processors)
Physical and logical memory banks
I/O ports
I/O buses
I/O cards
Using this command, the platform shell blacklists supersede the domain shell blacklists. For example, if a component is enabled in the platform shell, it will be enabled in all domains.
To enable a component that you previously disabled with the disablecomponent command in one or more shells or the platform, you must enable it in the same shells it was disabled.
Chapter 2 System Controller Alphabetical Command Reference 47
See Also
disablecomponent, showcomponent , and the Sun Fire 6800/4810/4800/3800
Systems Platform Administration Manual (for step-by-step procedure on removing a component from the blacklist).
Examples
This example of the enablecomponent command enables CPU/Memory board sb4 . This removes CPU/Memory board sb4 from the blacklist.
TABLE 2-13 enablecomponent Command Example Enabling CPU/Memory Board 4 schostname : A> enablecomponent sb4
This example of the enablecomponent command enables I/O assembly 6, port 1.
This removes port 1 of I/O assembly 6 from the blacklist.
CODE EXAMPLE 2-18 enablecomponent Command Example Enabling I/O Assembly 6 and Port 1 schostname : A> enablecomponent ib6/p1
48 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
flashupdate
Updates the flash PROMs in the system controller and the system boards
(CPU/Memory boards and I/O assemblies). The source flash image can be on a server or another board of the same type.
Scope platform shell
Syntax flashupdate [-y|-n] -f url all|systemboards|scapp|rtos| domainID flashupdate [-y|-n] -f url board [ board . . .
] flashupdate [-y|-n] -u flashupdate [-y|-n] -c source_board destination_board [ destination_board . . .
] flashupdate -h
Options/Parameters
-h displays help for this command.
-y does not prompt for confirmation.
-n does not execute this command if confirmation is required.
-f specifies a URL as the source of the flash images
url is the URL to the directory containing the flash images.
where: ftp:// hostname / path ftp://[ userid : password @] hostname / path
(userid:password@ is dependent on the system setup) http:// hostname / path http://[ userid : password @] hostname / path
The hostname you enter must be a complete host name (not a partial one).
board is the board name.
Chapter 2 System Controller Alphabetical Command Reference 49
-c specifies a board as the source of flash images.
■
■
source_board is the source board for the flash images.
destination_board is the destination board for the flash images.
-u automatically updates all of the boards from the board with the highest revision.
all updates the system controller and all system boards (CPU/Memory boards and
I/O assemblies). This option does not update the system controller real time operating system ( rtos ).
system_boards are all CPU/Memory boards and I/O assemblies. scapp updates the current system controller. Updating the system controller reboots the system controller twice. To update the other system controller, you must run the flashupdate command from the other system controller. Use showsc to determine which system controller is active.
rtos updates the real time operating system for the system controller. This action reboots the system controller twice.
domainID (a, b, c or d) is the domain where the flash PROMs on the board will be updated.
Caution – Any boards without power will not be updated.
Description
Updates the flash PROMs on the System Controller board, CPU/Memory board, I/O assembly, and the port of the system controller. There are no flash PROMs on
Repeater boards.
When you update the flash images, if you can do so, make sure the images are compatible. To verify the compatibility of the versions of scapp , CPU/Memory board, and I/O assembly PROMs, use the showboards -p proms command.
There is currently no method to determine that the scapp and rtos versions are compatible. Check all versions before you upgrade with the flashupdate command. If you fail to check all versions, the domains may crash or the system controller would fail to reboot normally.
50 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
All boards that are specified must be powered on and must be capable of being updating with the flashupdate command. Otherwise, the flashupdate command will not execute. Boards that are in a secure domain will not be updated.
Any time boards, the scapp , or rtos images are upgraded, check the Release Notes for any notes or special procedures.
Caution – Under normal circumstances, the flashupdate command will complete successfully. However, if the flashupdate command is terminated abnormally (such as a power failure, a failed network connection, and so on), the system controller goes into single user mode.
is a sample output showing the system controller entering singleuser mode.
Chapter 2 System Controller Alphabetical Command Reference 51
CODE EXAMPLE 2-19 Example of the flashupdate Command Entering Single-User Mode
RTOS version: 17
ScApp version: 5.11.3
SC POST diag level: min
Auto Flashupdate
S_errno_ECONNREFUSED http:// hostname /5.11.1/sgrtos.flash: cannot open file
Retrieving: http:/ hostname /5.11.1/sgrtos.flash
Flashupdate failed.
Single User Mode
The date is Thursday, February 15, 2001, 9:22:00 AM PST.
Feb 15 09:22:03 schostname Chassis-Port.SC: WARNING: hostid information is missing
Feb 15 09:22:03 schostname Chassis-Port.SC: Clock source: 75MHz
Feb 15 09:22:05 schostname Chassis-Port.SC: Starting Maintenance
Thread
Platform Shell schostname :SC> schostname :SC> help
Platform Shell commands: dumpconfig -- save the system controller configuration to a server flashupdate -- update flash prom images help -- show help for a command or list commands history -- show shell command history reboot -- reboot the system controller reset -- reset the other system controller restoreconfig -- restore the system controller configuration from a server schostname :SC>
To bring the system controller out of single-user mode and back into its normal operating mode, type the flashupdate command with a valid URL or use the reboot command to boot the system controller with an older firmware version.
52 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
See Also
Sun Fire 6800/4810/4800/3800 Systems Platform Administration Manual (for step-bystep procedures on how to update the firmware using flashupdate ).
flashupdate
Command Platform Shell—Examples
Note – In the following examples, since the output is very long, only the command syntax you type is in the code box.
Note – For the flashupdate all , flashupdate all rtos , flashupdate scapp , and the flashupdate rtos commands, all of these commands cause the system controller to reboot twice—one time to upgrade and one time to boot the new firmware.
■
To update the flash PROMs on the system controller and all CPU/Memory boards and I/O assemblies, make sure that all boards and assemblies are powered on. If a board or assembly is powered off, the flashupdate operation will fail. Type: schostname : SC> flashupdate -f ftp:// host / path all
■
That command reboots the system controller.
To update the flash PROMs on all CPU/Memory boards, I/O assemblies, and the system controller real time operating system ( rtos ), type: schostname : SC> flashupdate -f ftp:// host / path all rtos
■
That command reboots the system controller.
To update the flash PROMs on the system controller, perform this procedure from the platform console or watch the console output. Type: schostname : SC> flashupdate -f ftp:// host / path scapp
That command reboots the system controller.
Chapter 2 System Controller Alphabetical Command Reference 53
■
To update the active System Controller board and the system controller real time operating system ( rtos ), perform this procedure from the platform console or watch the console output. Type:
CODE EXAMPLE 2-20 flashupdate Example Updating the Active System Controller
Board and the System Controller Real Time Operating System schostname : SC> flashupdate -f ftp:// host / path scapp rtos
■
This reboots the system controller.
To upgrade the flash PROMs on all CPU/Memory boards and I/O assemblies
(system boards), make sure that all boards and assemblies are powered on. If a board or assembly is powered off, the flashupdate operation will fail. Type:
CODE EXAMPLE 2-21 flashupdate Example Updating System Boards (CPU/Memory
Boards and I/O Assemblies) schostname : SC> flashupdate -f ftp:// host / path systemboards
Reboot the domain containing the system boards that were updated in order to take advantage of the new features and bug fixes.
■ To upgrade the flash PROMs on CPU/Memory board 4 ( SB4 ), type:
CODE EXAMPLE 2-22 flashupdate Example Updating CPU/Memory Board 4 schostname : SC> flashupdate -f ftp:// host / path sb4
■
Reboot the domain containing the CPU/Memory board that was updated in order to take advantage of the new features and bug fixes.
To upgrade the flash PROMs on I/O assembly 8 ( IB8 ), type:
CODE EXAMPLE 2-23 flashupdate Example Updating I/O Assembly 8 schostname : SC> flashupdate -f ftp:// host / path ib8
Reboot the domain containing the I/O assembly that was updated in order to take advantage of the new features and bug fixes.
54 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
■
To update the system controller real time operating system ( rtos ), perform this procedure from the platform console or watch the console output. Type:
CODE EXAMPLE 2-24 flashupdate Example Updating the System Controller Real Time
Operating System schostname : SC> flashupdate -f ftp:// host / path rtos
This reboots the system controller.
Chapter 2 System Controller Alphabetical Command Reference 55
help
Without arguments, lists currently available system controller commands. When an argument is supplied, displays command usage of what you specified and a short description.
Scope platform shell, domain shell
Syntax help [command_name] | [partial_command_name] help -h
Options/Parameters
-h displays help for this command.
command_name is the name of the system controller command.
partial_command_name can be one letter of the command or a portion of the command name, such as show .
Description
The help command, without arguments, lists currently available commands in the system controller. When an argument is supplied, the help command displays a list of commands that begin with the specified argument. If only one command if found, full help is displayed. Otherwise, a short description is displayed for each command, beginning with the specified argument.
The help command is shell sensitive. It displays help information for the current shell only.
See Also
56 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
Examples
To display help information on the addboard command::
CODE EXAMPLE 2-25 help Command Example Displaying Information on the addboard
Command schostname : SC> help addboard addboard -- assign a board to a domain
Usage: addboard -d <domain> <board> ...
addboard -h
-d -- the domain to assign the board to
-h -- display this help message
To display all commands in the platform shell beginning with show:
CODE EXAMPLE 2-26 help Command Example Displaying Commands Beginning With the
Word show schostname : SC> help show showboards -- show board information showcomponent -- show state of a component showdate -- show the current date and time for the domain showenvironment -- show environment sensors showkeyswitch -- show the keyswitch position showlogs -- show the logs
To display all commands in the platform shell beginning with the letter a:
CODE EXAMPLE 2-27 help Command Example Displaying Commands Beginning With the
Letter A schostname : SC> help a addboard -- assign a board to a domain
Usage: addboard -d <domain> <board> ...
addboard -h
-d -- the domain to assign the board to
-h -- display this help message
Chapter 2 System Controller Alphabetical Command Reference 57
history
Shows the command history with date and time stamps.
Scope platform shell, domain shell
Syntax history [-h]
Options/Parameters
-h displays help for this command.
Description
Shows the command history with date and time stamps for when the commands were executed. This command is shown for your shell and displays the last twenty commands only.
See Also
Example
CODE EXAMPLE 2-28 history Command schostname : SC> history
1 : showboards
2 : showdate
3 : history
May 07 10:39:14
May 07 10:39:30
May 07 10:39:47
58 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
password
Sets the password for the platform or the domain.
Scope platform shell, domain shell
Syntax—Platform Shell password [-d domainID ] password -h
Syntax—Domain Shell password password -h
Options/Parameters
-h displays help for this command.
-d domainID is domain a, b, c, or d.
Description
Sets the password for the platform or the domain. There are separate passwords for each domain and for the platform. If you set a password, entering the password is required for access.
It is very important to set the password for the platform and each domain even if a domain is not being used. This prevents people from creating and activating unauthorized domains.
Prior to allowing the password to be changed, the current password will be authenticated. Changed passwords take effect immediately. The old password will no longer be accepted.
You can remove the password by pressing Return at the Enter new password and
Enter new password again prompts.
Chapter 2 System Controller Alphabetical Command Reference 59
OpenBoot PROM passwords are different from the platform and domain passwords.
The OpenBoot PROM in each domain supports the OpenBoot PROM security mode, which is a standard feature of the OpenBoot PROM software. For more information on the OpenBoot PROM security mode password, see your OpenBoot PROM documentation.
See Also
Sun Fire 6800/4810/4800/3800 Systems Platform Administration Manual (for a discussion of security).
Examples
You will see the following prompt (
CODE EXAMPLE 2-29 ), when a password is already
set and you type the password command at either the platform shell or the domain shell.
CODE EXAMPLE 2-29 password Command Example With No Password Set schostname : SC> password
Enter new password:
Enter new password again: schostname : SC>
If currently there is not a password assigned to the shell you are entering, you will not be prompted for the current password (
CODE EXAMPLE 2-30 password Command Example With a Password Already Set schostname : SC> password
Enter current password:
Enter new password:
Enter new password again: schostname : SC>
60 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
poweroff
Powers off a component (power grid, power supply, board, fan tray), or a list of components.
Scope platform shell, domain shell
Syntax for the Platform Shell poweroff [-y|-n] all| grid# | device_name [ device_names . . .
] poweroff -h
Syntax for the Domain Shell poweroff [-y|-n] all| device_name [ device_names . . .
] poweroff -h
Options/Parameters
-h displays help for this command.
-y will answer yes to any questions. This option is potentially hazardous. You can forcefully power off a component with the -y option.
-n answers no to any questions. You cannot forcefully power off a component with the -n option.
For a list of devices you power off, see the “Description” section.
Chapter 2 System Controller Alphabetical Command Reference 61
Description
Powers off a component or a list of components. You must specify device_name(s).
■
■
■
■
■
■
■
The components that can be powered off in the platform shell are: all turns off all currently controllable boards.
Power grid (grid0, grid1). The Sun Fire 6800 system has two power grids: grid0 and grid1 . Grid 1 controls power supplies ps3, ps4, and ps5. All other mid-range systems have one power grid, grid0. This grid controls power supplies ps0, ps1, and ps2.
Power supply (ps0 - ps5)
CPU/Memory board (sb0 - sb5 )
I/O assembly (ib6 - ib9)
Repeater board (rp0 - rp3)
Fan tray (ft0 - ft3)
■
■
The components that can be powered off in a domain shell are:
CPU/Memory board (sb0 - sb5 )
I/O assembly (ib6 - ib9)
For the domain shell, the specified board must be in the current domain.
All slots listed by showboards can be powered off except for system controllers
(SSC0 and SSC1) and the ID board. A powered-off component will not be monitored.
Use the showboards command to display the power status of each board.
You can power off any component except when the board is in the Active state (see the showboards command to display the board state). When a component is in the
Active state, you are asked to confirm with a warning of the consequences. If a board is active, a warning is displayed on the console advising you that the entire domain will go down.
If a board is active in a domain and you forcefully power off a device (board), the keyswitch for the domain will be set to standby. To change the keyswitch setting, use the setkeyswitch command.
Repeater boards do not have an Active state. You cannot power off a Repeater board because it is being used by the domain.
If the power supplies are needed to supply power to the boards and fans, you cannot power off the power supplies. If you power off a power supply, there might be insufficient power to support the current load.
If the fan trays are needed to cool the system, you cannot power them off because powering off fan trays result in insufficient cooling of the system.
62 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
See Also
poweron, setkeyswitch, showboards
Examples
To power off CPU/Memory board, sb2 from the platform shell, type:
CODE EXAMPLE 2-31 poweroff Command Example Showing Powering Off
CPU/Memory Board 2 schostname : SC> poweroff sb2
To power off all power supplies and currently controllable boards, type:
CODE EXAMPLE 2-32 poweroff Command Example Showing Powering Off All Power
Supplies and Currently Controllable Boards in the Platform Shell schostname : SC> poweroff all
To power off all CPU/Memory boards and I/O assemblies in domain A, type:
CODE EXAMPLE 2-33 poweroff Command Example Showing Powering Off All
CPU/Memory Boards and I/O Assemblies in Domain A schostname : A> poweroff all
To power off I/O assembly, ib7 from domain A, type:
CODE EXAMPLE 2-34 poweroff Command Example Showing Powering Off
I/O Assembly 7 schostname : A> poweroff ib7
Note – From the domain shell, you cannot power off power supplies, fan trays,
Repeater boards, or power grids. To power off these components, connect to the platform shell.
Chapter 2 System Controller Alphabetical Command Reference 63
poweron
Powers on a component (power grid, power supply, board, fan tray, or a list of components).
Scope platform shell, domain shell
Syntax for the Platform Shell poweron all| grid# | device_name [ device_names . . .
] poweron -h
Syntax for the Domain Shell poweron all| device_name [ device_names . . .
] poweron -h
Options/Parameters
-h displays help for this command.
For the grids and devices you can power on, see the “Description” section.
64 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
Description
Powers on a device or a list of devices You must specify device_name(s).
■
■
■
■
■
■
■
The components that can be powered on in the platform shell are: all is all power supplies and boards.
Power grid (grid0, grid1). The Sun Fire 6800 system has two power grids: grid0 and grid1. Grid 1 controls power supplies ps3, ps4, and ps5. All of the other midrange systems have one power grid, grid0 . All other mid-range systems have one power grid, grid0. This grid controls power supplies ps0, ps1, and ps2.
Power supply (ps0 - ps5)
CPU/Memory board (sb0 - sb5 )
I/O assembly (ib6 - ib9)
Repeater board (rp0 - rp3)
Fan tray (ft0 - ft3)
■
■
■
The components that can be powered on in a domain shell are: all powers on all CPU/Memory boards and I/O assemblies in the domain
CPU/Memory board (sb0 - sb5 )
I/O assembly (ib6 - ib9)
For the domain shell, the board status must be assigned to the current domain. You can power on any component except when the board is in the Active state (see the showboards command to display the board state). When a component is in the
Active state, you are asked to confirm with a warning of the consequences. Repeater boards do not have an Active state.
The fan trays power on automatically if any power supply is on. With the Sun Fire
6800/4810/4800 systems the power supplies power on automatically if a power supply in the same power grid is on. With the Sun Fire 3800 system, if grid power is on and the power supply switch is turned to the on position and the power cord is connected, the power supply powers on automatically.
See Also
Chapter 2 System Controller Alphabetical Command Reference 65
Examples
To power on CPU/Memory board, sb2 from the platform shell, type:
TABLE 2-14 poweron Command Example Showing Powering On CPU/Memory Board 2 schostname : SC> poweron sb2
To power on I/O assembly, ib7 , type:
TABLE 2-15 poweron Command Example Showing Powering On I/O Assembly 7 schostname : SC> poweron ib7
To power on CPU/Memory boards and I/O assemblies in the domain, type:
TABLE 2-16 poweron Command Example Showing Powering On All CPU/Memory
Boards and I/O Assemblies in Domain A schostname : A> poweron all
Note – From the domain shell, you cannot power on power supplies, Repeater boards, fan trays, or power grids. To power on these components, use the platform shell.
66 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
reboot
Reboots the system controller.
Scope platform shell
Syntax reboot [-y|-n] reboot -h
Options/Parameters
-y does not prompt for confirmation.
-n does not execute this command, confirmation is requested.
-h displays help for this command.
Description
Reboots the system controller. The reboot command will not change any configuration settings. Active domains will continue to run.
If you reboot the system controller while the keyswitch operation is in progress, the keyswitch is set to standby when the system controller completes rebooting.
See Also
Chapter 2 System Controller Alphabetical Command Reference 67
Example
To reboot the system controller, type: schostname : SC> reboot
To reboot the system controller with the -n option, type: schostname : SC> reboot -n
Are you sure you want to reboot the System Controller now? no (-n)
The -n option prompts you with the Are you sure . . .
prompt to answer.
Type y if you are sure you want to reboot the system controller. Type n if you do not want to reboot the system controller at this time.
68 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
reset
Resets the domain (in a domain shell) or the other system controller (in the platform shell).
Scope platform shell, domain shell
Syntax for the Platform Shell reset [-y|-n] ssc x reset -h
Syntax for the Domain Shell
Note – In the domain shell, typing reset , without options, is the same as typing reset -x .
reset [-y|-n][-x|-a] reset -h
Options/Parameters—Platform Shell
-y answers yes to the question asked (executes the command).
-n answers no to the question asked (does not execute the command).
-h displays help for this command.
ssc x (x is 0 or 1) performs a hardware reset of the other system controller.
Caution – The second System Controller board is installed in the system for clock failover. Do not use the second System Controller board unless it is necessary to reset the primary System Controller board.
Chapter 2 System Controller Alphabetical Command Reference 69
Options/Parameter—Domain Shell
-h displays help for this command.
-x resets via XIR (externally initiated reset). Uses XIR to try to obtain diagnostic data
(default).
-a reset is equivalent to the OpenBoot PROM reset-all command.
-y resets even if the domain is active.
-n does not reset if the domain is active.
Description—Platform Shell
To perform software reset on the other System Controller board, use ssc1 if you are using ssc0. If you are using ssc1, use ssc0. Clock failover will be automatically enabled after the reset is complete. Messages will be displayed on the platform console.
Description—Domain Shell
Resetting the domain is not allowed if the keyswitch is in the secure, off, or standby positions.
By default, reset uses XIR (externally initiated reset) to reset the CPU processors in the domain. The externally initiated reset forces control of the domain into the
OpenBoot PROM and begins the OpenBoot PROM error reset recovery actions. The error reset recovery actions preserve most domain states to allow collecting data needed for debugging the hardware and software, including a Solaris operating environment core file. The OpenBoot PROM error reset recovery actions are controlled by setting the OpenBoot PROM error-reset-recovery configuration variable. For the definition of this variable and the various settings, see
in
Section , “ setupdomain ” on page 2-85.
You cannot reset a domain that has been paused. The domain is paused automatically when hardware detects an error. Messages on the domain console indicate that the domain is paused. To rectify this situation, turn the keyswitch off with setkeyswitch off . Then, turn the keyswitch on with setkeyswitch on .
See Also
showdomain , showkeyswitch , Sun Fire
6800/4810/4800/3800 Systems Platform Administration Manual (for step-by-step procedures on recovering from a hung domain or hard hung domain).
70 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
Examples
To reset the domain (from a domain shell), type::
CODE EXAMPLE 2-35 reset Command Example From Domain A schostname : A> reset
This command uses XIR (externally initiated reset) to try to obtain diagnostic data.
To perform the equivalent operation as the OpenBoot PROM reset-all command, type:
CODE EXAMPLE 2-36 reset -a Command Example From Domain A schostname : A> reset -a
To reset system controller ssc0 from ssc1 , type:
CODE EXAMPLE 2-37 reset Command Example Resetting ssc0 From ssc1 in the
Platform Shell schostname : SC> reset ssc0
Chapter 2 System Controller Alphabetical Command Reference 71
restoreconfig
Restores the platform and domain configurations from a server.
Scope platform shell
Syntax restoreconfig [-y|-n] -f url restoreconfig -h
Options/Parameters
-h displays help for this command.
-y does not prompt for confirmation.
-n does not execute this command is confirmation is required.
-f specifies a URL to restore from.
url is the directory containing the data files. The supported protocols are ftp and http . For example: ftp://[ userid : password ]@ hostnam / path ftp:// hostname / path http://[ userid : password ]@ hostnam / path http:// hostname / path
Note – The hostname you enter must be a complete host name (not a partial one).
Description
Restores the platform and domain configurations based on two data files: schostanme .nvci
and schostname.
tod at the specified URL. This process requires that the Solaris operating environment must be halted in each domain. Also, all domains must be powered off with the setkeyswitch off command.
72 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
Use this command when the System Controller board failed and after a working
System Controller board is installed. You can also use this command when you want to restore the previous system controller configuration.
When the system controller configuration is restored, the system controller is rebooted. Set the date and time for the platform and for each domain using the setdate command.
The domains should be restored to their state when the configuration was stored.
For example, if a domain was active, it should be activated immediately. After running the restoreconfig command, check the state of the domains.
See Also dumpconfig, setkeyswitch, setdate
Example
shows an example of the restoreconfig command with the required -f option
CODE EXAMPLE 2-38 restoreconfig Example schostname : SC> restoreconfig -f ftp:// host / path
The system controller will be rebooted when the restore is complete. The date will need to be set in the platform and each domain.
Do you want to restore the system controller configuration now [no] yes
Retrieving: ftp:// host / path/schostname.
nvci
Retrieving: ftp:// host / path/schostname.
tod
Verifying data
NVCI has been restored
TOD has been restored
Restore complete. The system controller is being rebooted.
The date will need to be set in the platform and each domain.
Software Reset . . .
Chapter 2 System Controller Alphabetical Command Reference 73
resume
Exits the domain shell and resumes access to the domain console.
Scope domain shell
Syntax resume resume -h
Options/Parameters
-h displays help for this command.
Description
Exits the domain shell and resumes access to the domain console.
See Also
Example
CODE EXAMPLE 2-39 resume Command Example in Domain A
Domain A Shell schostname : A> showboards
Slot Pwr Component Type State
------------------- ------
SB0 On CPU Board Active
IB6 On PCI I/O Board Active schostname : A> resume
Status
------
Passed
Passed
Domain
------
A
A
74 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
setdate
Sets the date, time, and time zone for the platform and for domains.
Scope platform shell, domain shell
Syntax setdate [-v] [-t tz ] [mmdd ] HHMM [[ cc ] yy [ .SS ] setdate [-v] [-r datehost ] setdate [-v] -t tz setdate [-v] -t GMT <+|->offset from GMT (
setdate -h
Options/Parameters
-t tz sets the time zone using the time zone abbreviation (see
daylight savings time zones can be set. If you are in an area with daylight time or summer time, this is set automatically.
-t GMT <+|->offset from Greenwich Mean Time—GMT (see
).
mm = month number, dd = day number in the month, HH = hour number (24-hour system), MM = minute number, cc = century minus 1, yy = last two digits of the year number, and SS = second number. For the century minus 1 value, use 21 (Twenty first century) minus 1, which yields 20.
-r datehost sets the current time using rdate.
The host must be a valid system.
-v is verbose mode. Displays detailed information about the time zone that is set.
-h displays help for this command.
Chapter 2 System Controller Alphabetical Command Reference 75
TABLE 2-17 Time Zone Abbreviations, Time Zone Name, and Offsets From Greenwich
Mean Time
Time Zone Abbreviation
EST
HST
IET
IST
CTT
EAT
ECT
EET
ACT
AET
AGT
ART
AST
BET
BST
CAT
CNT
CST
JST
MET
MIT
MST
NET
NST
PLT
PNT
PRT
Time Zone Name
Australian central time
Australian eastern time
Argentina standard time
Arabic (Egypt) standard time
Alaska standard time
Brazil eastern time
Bangladesh standard time
Central African time
Canada Newfoundland time
Central standard time
China Taiwan time
Eastern African time
European central time
Eastern European time
Eastern standard time
Hawaii standard time
Indiana eastern standard time
India standard time
Japan standard time
Middle East time
Midway Islands time
Mountain standard time
Near East time
New Zealand standard time
Pakistan Lahore time
Phoenix standard time
Puerto Rico and U S. Virgin Islands time
Offset From Greenwich Mean Time
(GMT)
GMT+8
GMT+3
GMT+1
GMT+2
GMT-5
GMT-10
GMT-5
GMT+5.5
GMT+9.5
GMT+10
GMT-3
GMT+2
GMT-9
GMT-3
GMT+6
GMT+2
GMT-3.5
GMT-6
GMT+9
GMT+3.5
GMT-11
GMT-7
GMT+4
GMT+12
GMT+5
GMT-7
GMT-4
76 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
TABLE 2-17 Time Zone Abbreviations, Time Zone Name, and Offsets From Greenwich
Mean Time (Continued)
Time Zone Abbreviation
PST
SST
UTC
VST
Time Zone Name
Pacific standard time
Solomon standard time
Universal Time Coordinated
Vietnam standard time
Offset From Greenwich Mean Time
(GMT)
GMT-8
GMT+11
GMT+0
GMT+7
Description
Sets the date and time for the platform and domains. This command, when invoked from the platform, will have no effect on the date and time in each domain and vice versa. You can set up to five different times and time zones; one time and time zone for the platform and different times and time zones for each of the four domains.
If your time zone area is using daylight or summer time, this is set automatically.
Note – You cannot set the date from the system controller in a domain while the
Solaris operating environment is running. To set the date while the Solaris operating environment is running, use the Solaris operating environment date command.
See Also
Examples
When you type the setdate command from the platform, this sets the date and time for the platform. When you type the setdate command from the domain, this sets the date and time for the domain.
To set the date and time on the platform to Thursday, April 20, 2001, at 18 hours 15 minutes and 10 seconds, type:
TABLE 2-18 setdate Command Example in the Platform Shell schostname : SC> setdate 042018152001.10
Thu Apr 20 18:15:10 PST 2001
Chapter 2 System Controller Alphabetical Command Reference 77
To set the date from a date host:
CODE EXAMPLE 2-40 setdate -r Command Example Setting the Date From a Date Host schostname : SC> setdate -r datehost
To set the time zone to Pacific Standard Time (PST), using the offset from Greenwich mean time—GMT, and the date and time on the platform to Thursday, April 20,
2001, at 18 hours 15 minutes and 10 seconds (
), type:
CODE EXAMPLE 2-41 setdate -t Command Example Setting the Time Zone to Pacific
Standard Time Using the Offset From Greenwich Mean Time schostname : SC> setdate -t GMT-8 042018152001.10
Thu Apr 20 18:15:10 PST 2001
To set the time zone to Eastern Standard Time (EST), using the time zone abbreviations, and the date and time on the platform to Thursday, April 20, 2001, at
18 hours 15 minutes and 10 seconds (
CODE EXAMPLE 2-42 setdate -t Command Example Setting the Time Zone to Eastern
Standard Time Using Time Zone Abbreviations and Also Setting the
Date schostname : SC> setdate -t EST 042018152001.10
Thu Apr 20 18:15:10 EST 2001
To set just the time zone for Japan Standard Time using offsets from Greenwich
Mean Time—GMT (
) and not the date and time, type:
CODE EXAMPLE 2-43 setdate -t Command Example Setting the Time Zone to Japan
Standard Time Using the Offset From Greenwich Mean Time schostname : SC> setdate -t GMT+9
Thu Apr 20 18:15:10 GMP+9 2001
To set just the time zone for European Central Time using the time zone
abbreviations ( TABLE 2-17 ) and not the date and time, type:
CODE EXAMPLE 2-44 setdate -t Command Example Setting the Time Zone to Eastern
Central Time Using Time Zone Abbreviations schostname : SC> setdate -t ECT
Thu Apr 20 18:15:10 ECT 2001
78 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
setdefaults
Sets the default configuration values.
Caution – This is a destructive command. Use with caution and care.
Scope platform shell, domain shell
Syntax setdefaults [-y|-n] [-a] setdefaults -h
Options/Parameters
-y does not prompt for confirmation. The option reboots the system and sets the defaults.
-n does not execute the command if confirmation is requested.
-a adds missing parameters.
-h displays help for this command.
Chapter 2 System Controller Alphabetical Command Reference 79
Description
■
■
This command does the following:
■
Sets the system controller to the default values. When invoked for a domain, this command sets the defaults for that domain only. When invoked from the platform, this command sets the defaults for all domains and the platform.
Erases all platform and domain configurations (platform).
Removes passwords (domain and platform).
Caution – This command requires that all domains are inactive (not running the
OpenBoot PROM, POST, or the Solaris operating environment) and the virtual keyswitch be set to off.
See Also
Example
CODE EXAMPLE 2-45 setdefaults Example schostname : SC> setdefaults
WARNING!
You are about to reset all configuration data to default values.
All domain configurations, ACLs, users and data buffers will be lost.
The System Controller will be REBOOTED after the defaults are set.
Do you want to restore the default values and reboot now? [no]
If you answer yes, the system controller is rebooted after the defaults are set.
If you answer no, the default values are not restored.
If a password is set for the platform shell, the password will be required.
80 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
setkeyswitch
Changes the position of the virtual keyswitch to the specified value.
Scope platform shell, domain shell
Syntax for the Platform Shell setkeyswitch [-y|-n] -d domainID off setkeyswitch -h
Syntax for the Domain Shell setkeyswitch [-y|-n] [ off|standby | on | diag | secure ] setkeyswitch -h
Options/Parameters
-h displays help for this command.
-y does not prompt for confirmation.
-n does not execute this command is confirmation is requested.
-d domainID (platform shell only) is the domain ID of the domain you want power off ( a , b , c , or d ).
Chapter 2 System Controller Alphabetical Command Reference 81
For setkeyswitch parameters and descriptions, see
.
TABLE 2-19 setkeyswitch Values and Description
Value off on standby diag secure
Description
Changes the board state of all the boards belonging to a domain to the
Assigned board status and places the boards in low-power mode, which allows you to remove the boards from the system. The domain will not be initialized at system power-on.
Powers on and initializes the domain. The system controller brings the domain into OpenBoot PROM through POST. If the OpenBoot PROM has auto-boot?
set to true , then the Solaris operating environment boots automatically.
Changes the board state of all the boards belonging to a domain to the
Assigned board state and turns on the boards. The domain will not be initialized at system power on, but the boards that comprise the domain will be powered on.
Similar to the setkeyswitch on command except the POST verbose mode is set to on and the POST diagnostic level is set to maximum.
Similar to the setkeyswitch on command except that the break command and the reset commands are ignored. CPU/Memory board and
I/O assembly flash PROM updates are not allowed.
shows the results when you change a keyswitch setting.
off off on
Current Keyswitch off off off
TABLE 2-20 Results of Changing the Keyswitch From the Current Setting to a New Setting
New Keyswitch Setting Result off standby on diag secure secure
Keyswitch position not changed.
Changes the board state of all the boards belonging to a domain to Assigned and powers on all of the boards. The domain will not be initialized at system power on.
Powers on and initializes the domain. The domain will go through POST and the OpenBoot PROM. The Solaris operating environment boots automatically unless you have set the OpenBoot PROM auto-boot?
set to false.
Similar to on, except POST verbose and diagnostic level is to set to maximum. The domain will boot from the diag-device.
Similar to on, except the reset and break commands are ignored by the domain shell.
break and reset are ignored.
82 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
Current Keyswitch secure standby diag standby secure on diag
TABLE 2-20 Results of Changing the Keyswitch From the Current Setting to a New Setting
(Continued)
New Keyswitch Setting Result on on on off break and reset are not ignored.
Similar to setting the virtual keyswitch from off to on except that you do not have to wait for the system controller to turn on the boards and prepare them.
Has no effect on a running domain. This operation only changes the keyswitch position and does not perform any other function since the domain is already running.
All boards will be powered off (set to low -power mode and all monitoring of the boards will stop.
Description
Each domain has a virtual keyswitch with five positions: off, standby, on, diag, and secure. The setkeyswitch command changes the position of the virtual keyswitch to the specified value. The virtual keyswitch replaces the need for a physical keyswitch for each domain.
This command is also available in the platform shell. This command is meant to be used in the platform shell in case of problems with a domain. From the platform shell, you can only turn the virtual keyswitch off. This action shuts down the domain. Turn the keyswitch off from the domain, if possible.
If the domain is running the Solaris operating environment, the setkeyswitch command parameters off and standby require confirmation.
If the domain is already powered on, the setkeyswitch on , setkeyswitch diag , and setkeyswitch secure commands will change only the position of the virtual keyswitch. If components making up a domain such as a I/O assembly or
CPU/Memory board need to be powered on, the system attempts to power on these boards or devices also.
If a failure occurred during keyswitch transition, it will be reset to off or to standby after recovering from the failure.
The system controller maintains the position of each keyswitch even during power failures or physical power cycles.
Chapter 2 System Controller Alphabetical Command Reference 83
See Also
Examples
To turn the virtual keyswitch on and power on the domain, type:
TABLE 2-21 setkeyswitch on Example schostname : A > setkeyswitch on
To shut down the domain by turning the virtual keyswitch off, type:
TABLE 2-22 setkeyswitch off Example schostname : A> setkeyswitch off
To shut down domain B from the platform shell type:
TABLE 2-23 setkeyswitch off Example Shutting Down Domain B From the Platform
Shell schostname : SC> setkeyswitch -d b off
84 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
setupdomain
Sets up domain specific parameter values and configures the domain.
Scope domain shell
Syntax setupdomain [-p part ] . . .
setupdomain -h
Options/Parameters
-h displays help for this command.
-p part configures the specified information and has the following options:
■
■
■ bootparams configures the boot parameter information.
loghost configures the log hosts— loghost [: facility ] snmp configures SNMP information.
describes each parameter value.
Description
Sets up domain specific values. Configures the domain. You can configure each domain differently and independently.
See Also
Chapter 2 System Controller Alphabetical Command Reference 85
Example
CODE EXAMPLE 2-46 Variables for the setupdomain Command schostname : A > setupdomain
Domain Boot Parameters
---------------diag-level [off]: verbosity-level [min]: error-level [max]: interleave-scope [within-board]: interleave-mode [optimal]: reboot-on-error [false]:
OBP.use-nvramrc? [<OBP default>]:
OBP.auto-boot? [<OBP default>]:
OBP.error-reset-recovery [<OBP default>]:
Log hosts
---------
Loghost [ ]: The name or the IP address of the loghost for this domain.
The format is loghost :[f acility ].
Note that facility is defined by the Solaris operating environment systlogd in /etc/syslog.conf.
SNMP
-----
Domain Description[]: A brief description for this domain (its function).
Domain Contact[]: The name of the primary domain administrator.
Trap Hosts [( )]: The IP address of the loghost for this domain
Public Community String [ ]: The a uthentication string for SNMP readers. .
Private Community String [ ]: Type the a uthentication string for readers and writers.
If you enter an invalid value, the system controller displays “invalid entry” and
prompts you to enter a proper value ( TABLE 2-24 ). If a value is not specified, it retains
its current value. When an invalid entry is entered, it also lists the valid responses.
Typing a dash ( - ), clears the entry.
Current values are displayed in [ ].
lists the setupdomain parameter values.
86 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
Parameter diag-level verbosity-level error- level interleave-scope interleave-mode reboot-on-error
TABLE 2-24 Parameter Values for the setupdomain Command
Value Description default (default value) All system board components are tested with all tests and test patterns, except for memory and Ecache modules. For memory and Ecache modules, all locations are tested with multiple patterns. More extensive, time-consuming algorithms are not run at this level.
init Only system board initialization code is run. No testing is done. This is a very fast pass through
POST.
quick mem1 mem2 off min max off min
(default value)
All system board components are tested using few tests with few test patterns.
Runs all tests at the default level plus more exhaustive DRAM and SRAM test algorithms.
This is the same as mem1 with the addition of a
DRAM test that does explicit compare operations of the DRAM data.
No status messages are displayed.
Test names status messages, and error messages are displayed.
Subtest trace messages are displayed.
No error messages are displayed.
The failing test name is displayed.
max (default value) within-boar d (default value)
All relevant error status is displayed.
The memory banks on a system board will be interleaved with each other.
across-boards The memory will be interleaved on all memory banks across all of the boards in the domain.
optimal (default value) The memory is mixed-size interleaving in order to gain optimal performance.
fixed off false true
(default value)
The memory is fixed-size interleaving.
There is no memory interleaving.
The domain will be paused when there is an error.
The domain will be rebooted.
Chapter 2 System Controller Alphabetical Command Reference 87
Parameter
OBP.use-nvramrc?
OBP.auto-boot?
TABLE 2-24 Parameter Values for the setupdomain Command (Continued)
Value
OBP.error-reset-recovery true false (default value) true (default value) false sync (default value) none boot
Description
This parameter is the same as the OpenBoot PROM nvramrc?
parameter. This parameter uses aliases that are stored in nvramrc .
The OpenBoot PROM executes the script stored in nvramr c if this parameter is set to true.
The OpenBoot PROM does not evaluate the script stored in nvramr c if this parameter is set to false.
Controls booting of the Solaris operating environment.
If this value is true, the domain boots automatically after POST has run.
If this parameter value is set to false, you will obtain the OpenBoot PROM ok prompt after POST runs, from which you must type a boot command to boot the Solaris operating environment.
Controls the behavior of the domain after an externally initiated reset (XIR) as well as a red mode trap.
The OpenBoot PROM invokes sync . A core file is generated. If the invocation returns, the OpenBoot
PROM performs a reboot.
The OpenBoot PROM prints a message describing the reset trap that triggered the error reset and passes control to the OpenBoot PROM ok prompt. The message describing the reset trap type is platform specific.
The OpenBoot PROM firmware reboots the domain.
A core file is not generated. Rebooting a domain occurs using the OpenBoot PROM settings for diag-device or boot-device , depending on the value of the OpenBoot PROM configuration variable diag-switch?
Log Host
If diag-switch?
is set to true, the device names in diag-device will be the default for boot. If diag-switch?
is set to false, the device names in boot-device will be the default for boot.
The name or the IP address of the loghost for this domain (SNMP). The format is loghost:[facility]. Note that facility is defined by the Solaris operating environment systlogd in /etc/syslog.conf
.
88 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
Parameter
Domain Description
Trap Hosts
Public Community
String
TABLE 2-24 Parameter Values for the setupdomain Command (Continued)
Value Description
Enter a brief description for this domain. For example, its function.
Enter the name of the primary domain administrator.
Enter the name or the IP address of the trap host for this domain.
Authentication string for SNMP readers. The default value is A-public, B-public, and so on.
Private Community
String
Note—Make sure that the value in this field is the same as the Sun Management Center software for the
Sun Fire 6800/4810/4800/3800 systems value for public community string.
Authentication string for readers and writers. The default value is A-private, B-private, and so on.
Note—Make sure that the value in this field is the same as the Sun Management Center software for the
Sun Fire 6800/4810/4800/3800 systems value for private community string.
Chapter 2 System Controller Alphabetical Command Reference 89
setupplatform
Configures the platform specific variables.
Scope platform shell
Syntax setupplatform [-p part ]. . .
setupplatform -h
Options/Parameters
-h displays help for this command.
-p part . . . configures the specified part and has the following options:
■ acls is ACLs (Access Control List)
clears the boards from the ACL
+ adds all boards to the ACL
-a board . . . adds a board
-d board . . . deletes a board
■
■
■
■
■
loghost is the IP address or hostname of the syslog loghost in the format loghost [: facility ] ( The hostname you enter must be a complete host name (not a partial one).
network is the network settings partition sets the partition mode to single (one partition) or dual (two partitions) sc is the system controller POST diag level snmp is SNMP configuration ( The hostname you enter must be a complete host name (not a partial one).
Description
Sets up platform specific values. For the parameters you can configure, see
90 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
TABLE 2-25 setupplatform Parameter Values
Parameter
Is the System Controller on a
Network?
Use DHCP or static network settings?
Description
If the answer is no, leave all network parameters as unconfigured
•
DHCP means the system controller network configuration is retrieved from a DHCP server.
Hostname (Network parameter)
IP address (Network parameter)
Netmask (Network parameter)
Gateway (Network parameter)
DNS Domain (Network parameter)
Primary DNS Server (Network parameter)
Secondary DNS Server (Network parameter)
Loghost
•
Static means the network settings will be manually configured. If you select the static setting, you will be asked for the following network parameters.
The human readable network identity for this system controller.
The network identity used by computers.
For this value, specify how much of the address should be reserved for subdividing networks into subnetworks. Must be specified in dot-notation address. For example
255.255.255.0
.
IP address of the gateway.
Domain name. For example, xxx .
xxx .com
.
IP address of your primary DNS server.
IP address of your secondary DNS server.
SNMP Agent?
IP address or hostname of the system that will accept syslog messages. The format is loghost[:facility]. For example,
IP address:local0. Errors, warnings, and some command will be logged to this system.
The SNMP agent enables or disables SNMP.
Platform Description
Platform Contact
Platform Location
Trap Hosts
Default value is the platform model name.
The name of the person who is responsible for this system.
This name will be used by SNMP. Note that if SNMP is not going to be enabled, this field is informational only.
Geographic location of the system. This information will be used by SNMP. Note that if SNMP is not going to be enabled, this field is informational only.
IP address or name of the trap host (SNMP).
Chapter 2 System Controller Alphabetical Command Reference 91
off min max
TABLE 2-25 setupplatform Parameter Values (Continued)
Parameter
Public Community String
Private Community String
ACL for Domain A
ACL for Domain B
ACL for Domain C
ACL for Domain D
SC POST diag level
Configure platform for single or dual partition mode
Description
Authentication string for SNMP readers. The default is
P-public .
Authentication string for readers and writers. The default is
P-private .
Default value is to have all slots assigned to all domains.
• Prefixing a slot name with -d deletes the slot from ACLs of this domain.
• Typing a prefix of -a (add) adds a slot.
• Typing a dash ( ) clears the entire list.
• Typing a + (plus sign) adds all.
• Pressing the Return key does not change the value displayed inside [ ].
See the description for ACL for Domain A.
See the description for ACL for Domain A.
See the description for ACL for Domain A.
The system controller boot parameters (diag level) can be set to: off , min , or max .
Only system board initialization code is run. No testing is done. POST is not run.
All system board components are tested using few locations with few test patterns.
All system board components are tested with all tests and test patterns.
The two options are single or dual. The default is single. For a description of single and dual partition mode, refer to the
“Overview” chapter in the Sun Fire 6800/4810/4800/3800
Systems Platform Administration Manual.
See Also
,
Fire 6800/4810/4800/3800 Systems Platform Administration Manual (for a step-by-step procedure on using
).
92 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
Example
CODE EXAMPLE 2-47 Output From setupplatform Command schostname : SC> setupplatform
Network Configuration
---------------------
Is the System Controller on a network? [yes]
Network settings? [static]:
Hostname []:
IP Address []:
Netmask []:
Gateway []:
DNS Domain []:
Primary DNS Server []:
Secondary DNS Server []:
Loghost [ ]:
SNMP
----
Platform Description [Sun Fire 6800]: System type
Platform Contact [ ]: Platform administrator’s name
Platform Location [ ]: Geographic system location
Enable SNMP Agent? [yes]:
Trap Hosts []: SNMP trap host IP address or name
Public Community String [P-public]: Authentication string for SNMP readers
Private Community String [P-private]: Authentication string for readers and writers
ACLs
----
ACL for domain A [SB0 SB1 SB2 SB3 SB4 SB5 IB6 IB7 IB8 IB9 ]:
ACL for domain B [SB0 SB1 SB2 SB3 SB4 SB5 IB6 IB7 IB8 IB9 ]:
ACL for domain C [SB0 SB1 SB2 SB3 SB4 SB5 IB6 IB7 IB8 IB9 ]:
ACL for domain D [SB0 SB1 SB2 SB3 SB4 SB5 IB6 IB7 IB8 IB9 ]:
SC POST
-------
SC POST diag level [min]:
Partition Mode
--------------
Configure platform for single or dual partition mode? [single]:
Chapter 2 System Controller Alphabetical Command Reference 93
showboards
Displays the assignment information and status for all of components in the system.
Scope platform shell, domain shell
Syntax for the Platform Shell showboards [ -ev ] [ -y | -n ] [ -d domainID] [ -p part] showboards -h
Syntax for the Domain Shell showboards [ -ev ] [ -y|-n ] -d domainID] [ -p part ] . . .
showboards -h
Options/Parameters
-e includes empty slots in the output.
-v shows boards including shared components and empty slots for the platform shell only. Verbose mode for parts.
-d domainID (platform shell only) is a, b, c, or d. Displays information for boards assigned to that domain.
-p part shows only a specific part and can be:
■
■
■ cpu shows you CPU information.
proms shows you the firmware revision of the PROMs.
memory shows memory information.
-y answers yes to all questions.
-n answers no to all questions.
-h displays help for this command.
94 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
Description
Displays the assignment information and status for all of the components in the system. For example, CPU/Memory boards, I/O assemblies, fan trays, and so on.
For the domain shell, the display shows components assigned to the domain and can also include boards that are included in the ACL, but not assigned to any other domain.
See Also
addboard, deleteboard, testboard
Examples—Platform Shell
CODE EXAMPLE 2-48 showboards Command for the Platform Shell schostname : SC> showboards
Slot Pwr
------
/N0/SB0 On
/N0/SB2 On
/N0/SB4 On
/N0/IB6 On
/N0/IB7 On
/N0/IB8 On
Component Type
--------------
CPU Board
CPU Board
CPU Board
PCI I/O Board
PCI I/O Board
PCI I/O Board
State
-----
Active
Active
Active
Active
Active
Active
Status
------
Passed
Passed
Passed
Passed
Passed
Passed
A
C
C
D
D
Domain
------
A
The showboards command with the -v option displays the grid number.
PS0
PS1
PS2
0
0
0
CODE EXAMPLE 2-49 showboards -v Command for the Platform Shell schostname : SC> showboards -v
Slot
----
SSC0
SSC1
ID0
Grd
---
-
-
-
Pwr
---
On
On
On
On
On
-
Component Type
--------------
System Controller
System Controller
Sun Fire 6800
Centerplane
A152 Power Supply
A152 Power Supply
Empty Slot
State
-----
-
-
-
-
-
-
Status
------
Passed
-
-
OK
OK
-
-
-
-
-
-
Domain
------
-
Chapter 2 System Controller Alphabetical Command Reference 95
CODE EXAMPLE 2-49 showboards -v Command for the Platform Shell (Continued)
PS3
PS4
PS5
FT0
FT1
FT2
FT3
RP0
RP1
RP2
RP3 1
/N0/SB0 0
0
1
/N0/SB1 1
/N0/SB2 0
/N0/SB3 1
/N0/SB4 0
/N0/SB5 1
/N0/IB6 0
/N0/IB7 1
/N0/IB8 0
/N0/IB9 1
1
1
1
0,1
0,1
0,1
0,1
0
On
Off
Off
Off
On
On
On
Off
On
On
On
On
On
On
On
On
On
On
Off
Off
Off
A152 Power Supply
A152 Power Supply
A152 Power Supply
Fan Tray
Fan Tray
Fan Tray
Fan Tray
Repeater Board
Repeater Board
Repeater Board
Repeater Board
CPU Board
CPU Board
CPU Board
CPU Board
CPU Board
CPU Board
PCI I/O Board
PCI I/O Board
PCI I/O Board
PCI I/O Board
-
-
OK
OK
OK
Low Speed OK
Low Speed OK
Low Speed OK
Low Speed OK
OK
-
-
-
Assigned
Active
Assigned
Assigned
Assigned
Active
Active
Assigned
Assigned
Assigned
OK
OK
OK
Not tested
Passed
Degraded
Degraded
Not tested
Passed
Passed
Not tested
Not tested
Not tested
A
A
A
A
-
A
-
-
B
C
A
A
D
-
-
-
-
-
-
-
-
TABLE 2-26 Output Header Definitions for the showboards -v Command
Header
Slot
Grd
Pwr
Component type
State
Status
Description
Slot designator. The Nx in the slot descriptor is the node number.
The power grids (in the Sun Fire 6800 system) or the power grid (in the other mid-range systems the system gets power from.
Indicates if the power status of the device is off or on.
Component description.
Describes board state. Possible values are: Active, Assigned,
Available and – (dash) (TABLE 2-3). The - board state means that the
board state does not apply to this slot.
Contains the result of the testboard command or POST. Possible values are Passed, Failed, Not Tested, Degraded, Under Test, and
96 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
TABLE 2-26 Output Header Definitions for the showboards -v Command (Continued)
Header
Domain
Description
Indicates which domain the board belongs to: Possible values are:
• A-D—The Sun Fire 6800 systems can have up to four active domains (A – D). The other mid-range systems can have up to four domains, but only two domains can be active domains. Active domains must contain an I/O assembly and a CPU/Memory board.
For more information on domains, refer to the Sun Fire
6800/4810/4800/3800 Systems Platform Administration Manual.
• Isolated—The board does not belong to a domain.
• – (dash) The board cannot be assigned to a specific domain. It is a shared resource.
Example—Domain Shell
CODE EXAMPLE 2-50 showboards Command for the Domain Shell schostname : A> showboards
Showing boards for domain A
Slot Pwr Component Type
-------------------
State
------
/N0/SB0 On CPU Board
/N0/SB2 Off CPU Board
Active
Assigned
/N0/SB4 Off CPU Board
/N0/IB6 On
Assigned
PCI I/O Board (F4800) Active
Status
------
Passed
Not Tested
Not Tested
Passed
A
A
A
A
Domain
------
Chapter 2 System Controller Alphabetical Command Reference 97
showcomponent
Shows the state of a component.
Scope platform shell, domain shell
Syntax showcomponent board_name showcomponent -h
Options/Parameters
-h displays help for this command. Includes component_name syntax.
■
boardname for CPU/Memory boards is SB0 - SB5
■
boardname for I/O assemblies is IB6 - IB9
Description
Shows the state of a component and details about the components on a board.
See Also
enablecomponent, disablecomponent , Sun Fire 6800/4810/4800/3800 Systems
Platform Administration Manual (for a step-by-step procedure on displaying a component).
98 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
Examples
shows sample output for the showcomponent sb4 command.
The abbreviations for the Component field are:
■
■
■
■
■
N x Node name
SB x CPU/Memory board, where x is 0 – 5
P x Port, where x is 0 – 3
B x
Lx
Physical memory bank, where x is 0 – 1
Logical memory bank, where x is 0 – 3
CODE EXAMPLE 2-51 showcomponent sb4 Sample Output schostname : SC> showcomponent sb4
Component Status Pending POST
--------
/NO/SB4/P0
/NO/SB4/P1
/NO/SB4/P2
--------------enabled enabled enabled pass pass pass
/NO/SB4/P3 enabled -
/NO/SB4/P0/B0/L0 enabled -
/NO/SB4/P0/B0/L2 enabled -
/NO/SB4/P0/B1/L1 enabled -
/NO/SB4/P0/B1/L3 enabled -
/NO/SB4/P1/B0/L0 enabled -
/NO/SB4/P1/B0/L2 enabled -
/NO/SB4/P1/B1/L1 enabled pass pass pass pass pass pass pass pass
/NO/SB4/P1/B1/L3 enabled -
/NO/SB4/P2/B0/L0 enabled -
/NO/SB4/P2/B0/L2 enabled -
/NO/SB4/P2/B1/L1 enabled -
/NO/SB4/P2/B1/L3 enabled -
/NO/SB4/P3/B0/L0 enabled -
/NO/SB4/P3/B0/L2 enabled -
/NO/SB4/P3/B1/L1 enabled -
/NO/SB4/P3/B1/L3 enabled pass pass pass pass pass pass pass pass pass
Description
-----------
UltraSPARCIII,750Mhz, 8M Cache
UltraSPARCIII,750Mhz, 8M Cache
UltraSPARCIII,750Mhz, 8M Cache
UltraSPARCIII,750Mhz, 8M Cache
256M DRAM
256M DRAM
256M DRAM
256M DRAM
256M DRAM
256M DRAM
256M DRAM
256M DRAM
256M DRAM
256M DRAM
256M DRAM
256M DRAM
256M DRAM
256M DRAM
256M DRAM
256M DRAM
Chapter 2 System Controller Alphabetical Command Reference 99
where:
Component is the name of the board and its components.
Status is the status of the board or component.
Pending
POST is the status of POST (passed or failed).
Description is a description of the board or component.
shows sample output for the showcomponent ib6 command.
The abbreviations for the Component field are:
■
■
■
■
■
N x Node name
IB x I/O assembly, where x is 6 – 9
P x Port, where x is 0 – 1
Bx
C x
Bus, where x is 0 – 1
Card in the I/O assembly, where x is 0 – 7
CODE EXAMPLE 2-52 showcomponent ib6 Sample Output schostname : SC> showcomponent ib6
Component
---------
Status
-------
Pending
-------
POST
----
/N0/IB6/P0
/N0/IB6/P1
/N0/IB6/P0/B1
/N0/IB6/P0/B0 enabled enabled enabled enabled
-
-
-
pass pass untest untest
/N0/IB6/P0/B1/C0 enabled -
/N0/IB6/P0/B1/C1 enabled -
/N0/IB6/P0/B1/C2 enabled -
/N0/IB6/P0/B1/C3 enabled untest untest untest untest
Description
-----------
IO controller 0
IO controller 1
66/33MHz PCI Bus
33MHz PCI Bus
33MHz 5V Short PCI card
33MHz 5V Short PCI card
33MHz 5V LOng/Short PCI card
33MHz 5V LOng/Short PCI card
100 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
showdate
Displays the current date and time for the platform or domain.
Scope platform shell, domain shell
Syntax showdate [-t] [-v] showdate -h
Options/Parameters
-h displays help for this command.
-t lists available time zones.
-v is verbose mode.
Description
Displays the current date and time for the platform.
See Also
Chapter 2 System Controller Alphabetical Command Reference 101
Example—Platform Shell
CODE EXAMPLE 2-53 showdate Command for the Platform Shell schostname : SC> showdate
Mon Apr 03 12:31:40 EDT 2001
Example—Domain Shell
CODE EXAMPLE 2-54 showdate Command for the Domain Shell schostname : A> showdate
Mon Apr 03 12:31:40 EDT 2001
102 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
showdomain
Displays the domain parameter settings, which is the status and non-configurable information for the current domain.
Scope domain shell
Syntax showdomain [-v] [-p part ] . . .
showdomain -h
Options/Parameters
This command without any arguments displays all the parameter values configured by the setupdomain command.
-v is verbose mode.
-p part is a parameter for the information to display:
■
■
■
■
■
■ acls shows the ACLs (Access Control List) bootparams shows boot parameter information loghosts shows the log hosts mac shows MAC addresses s nmp shows SNMP configuration status shows domain status
-h displays help for this command.
Description
Displays the domain parameter settings, which is the status and non-configurable information for the current domain.
See Also
Chapter 2 System Controller Alphabetical Command Reference 103
Example
To display parameters assigned by the setupdomain command, type showdomain .
CODE EXAMPLE 2-55 showdomain Command Example schostname : A> showdomain
Domain Solaris Nodename Domain Status Keyswitch
-----------------------------------------
A Powered Off off
Domain Boot Parameters
---------------------diag-level = off verbosity-level = min error-level = max interleave-scope = within-board interleave-mode = optimal reboot-on-error = true
OBP.use-nvramrc? = true
OBP.auto-boot? = false
OBP.error-reset-recovery = none
Loghost for Domain A:
SNMP Agent: enabled
Domain Description:
Domain Contact:
Trap Hosts:
Public Community String: P-public
Private Community String: P-private
ACL for Domain A: SB0 SB1 SB2 SB3 SB4 SB5 IB6 IB7 IB8 IB9 schostname : A>
To display the verbose output of parameters assigned by the setupdomain command, type
showdomain -v ( CODE EXAMPLE 2-56
) .
104 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
CODE EXAMPLE 2-56 showdomain -v Command Example schostname : A> showdomain -v
Domain Solaris Nodename Domain Status Keyswitch
-----------------------------------------
A Powered Off off
Domain Boot Parameters
---------------------diag-level = off verbosity-level = min error-level = max interleave-scope = within-board interleave-mode = optimal reboot-on-error = true
OBP.use-nvramrc? = true
OBP.auto-boot? = false
OBP.error-reset-recovery = none
Domain A
MAC Address HostID
-----------------xx : xx : xx : xx : xx : xx xxxxxxxx
Loghosts
--------
Loghost for Domain A:
SNMP
----
SNMP Agent: enabled
Domain Description:
Domain Contact:
Trap Hosts:
Public Community String: P-public
Private Community String: P-private
SNMP packets received: x
SNMP packets sent: xx
SNMP traps sent: xxx
ACLs
----
ACL for Domain A: SB0 SB1 SB2 SB3 SB4 SB5 IB6 IB7 IB8 IB9
Chapter 2 System Controller Alphabetical Command Reference 105
To display boot parameter information, type:
CODE EXAMPLE 2-57 showdomain -p bootparams Example Displaying Boot Parameter
Information schostname : A> showdomain -p bootparams diag-level = off verbosity-level = min error-level = max interleave-scope = within-board interleave-mode = optimal reboot-on-error = false
OBP.use-nvramrc? = true
OBP.auto-boot? = false
OBP.error-reset-recovery = sync schostname : A>
106 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
showenvironment
Displays the current environmental status, temperatures, currents, voltages, and fan status, for the system (platform shell) or the current domain (domain shell).
Scope platform shell, domain shell
Syntax for the Platform Shell showenvironment [-ltvuw] [-d domainID ] [-p part ] showenvironment [-ltvuw] device_name showenvironment -h
Syntax for the Domain Shell showenvironment [-ltvuw] [-p part ] showenvironment [-ltvuw] device_name showenvironment -h
Options/Parameters
-h displays help for this command.
-l displays the limits that apply to each selected measurement. These values are the threshold for each measurement. Exceeding the threshold causes the status to display Max or Min .
-d domainID is a, b, c, or d (platform shell only). Displays information for boards assigned to that domain.
-p
part shows a specific part ( TABLE 2-27 ).
t prints header titles.
-u updates data now. Polls all sensors for new values.
v is verbose mode. This is the equivalent of the options -l and w .
-w shows warning thresholds.
Chapter 2 System Controller Alphabetical Command Reference 107
device_name is the name of the board. Displays information for this board only.
TABLE 2-27 showenvironment -p part Descriptions
Report currents faults temps voltage fans
Description
Currents (power supplies only)
Displays only measurements that are above High or below Low
Shows temperatures only.
Shows voltages only.
Shows fan states.
Description
Displays the current environmental status, temperatures, currents, voltages, and fan status for the system (platform shell) or the current domain (domain shell). In order for this command to be recognized in a domain shell, the boards must be assigned to the domain and the boards must be powered on. If you are running the command from the domain shell only, system boards assigned to the domain are displayed.
This command also displays minimum and maximum allowable values for each component being monitored. Samples are updated periodically, but the operator can get new samples by providing the proper argument. If no arguments are supplied, all applicable environmental information will be displayed.
describes the showenvironment output headers.
TABLE 2-28 showenvironment Output Header Description
Value Header
Slot
Device
Sensor
Value
Units
C
V
Description
Slot ID
Device being monitored by the sensor
Component that measures the environmental data of the device
Value returned by the sensor ( data was acquired seconds ago)
Applicable unit for the sensor (for valid units, see the Value column)
Celsius
Volts
108 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
TABLE 2-28 showenvironment Output Header Description (Continued)
Header
Age
Status
LoWarn
HiWarn
Min
Max
Value
A max high low min ok
Description
Amps
Age of the reading being displayed (seconds)
Values for Status. See the Value column
Value exceeded Max threshold (fault condition)
Value below High threshold (fault condition)
Value exceeded Low threshold (warning condition)
Value below Min threshold (warning condition)
Value is within range (within Low and High)
Displayed only with the -v and -w options.
Generates a warning message when the temperature is below the acceptable value.
Displayed only with the -v and -w options.
Generates a warning message when the temperature is above the acceptable value.
Displayed only with the -l option. Value below
Min threshold (warning condition).
Displayed only with the l option. The value exceeded Max threshold (fault condition).
See Also
Example
The showenvironment command display for the platform shell returns information on the slot number, device, sensor, value, units, age, and status, as shown in
Chapter 2 System Controller Alphabetical Command Reference 109
CODE EXAMPLE 2-58 showenvironment Platform Shell and Domain Shell Example
.
.
.
RP0
PS0
PS0
PS0
.
.
IB7 schostname : SC> showenvironment
Slot
----
Device
------
Sensor
------
Value Units
---------
SBBC 0 Temp. 0 48 Degrees C SSC0
.
.
SB0 Board 0 1.5 VDC 0 1.51 Volts DC
.
.
/NO/SB2 Board 0 3.3 VDC
/NO/SB2 SDC 0 Temp. 0
.
.
/NO/IB6 Board 0 Temp. 0
.
0
49
28
3.27 Volts DC
Degrees C
Degrees C
Board 0 Temp. 0 26
48 VDC 0 Current 0 N/A
48 VDC 0 48 VDC 0
48 VDC 0 Temp. 0
Board 0 Temp. 0
N/A
N/A
27
Degrees C
9.63 Amps
56.33 Volts DC
37 Degrees C
Degrees C
Age
---
7 sec
1 sec
1 sec
1 sec
9 sec
11 sec
2 sec
2 sec
2 sec
13 sec
Status
-----ok ok ok ok ok ok ok ok ok ok
110 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
showkeyswitch
Displays the keyswitch setting.
Scope platform shell, domain shell
Syntax for the Platform Shell showkeyswitch [-v] -d domainID showkeyswitch -h
Syntax for the Domain Shell showkeyswitch [-v] showkeyswitch -h
Options/Parameters
-h displays help for this command.
-v is verbose mode.
d domainID (platform shell only) is a , b , c , or d .
See Also
Description
Displays the keyswitch setting.
Chapter 2 System Controller Alphabetical Command Reference 111
Examples
CODE EXAMPLE 2-59 s howkeyswitch Example Showing the Keyswitch Set to On schostname : A> showkeyswitch key switch is: on
CODE EXAMPLE 2-60 s howkeyswitch Example Showing the Keyswitch Set to Off schostname : A> showkeyswitch key switch is: off
CODE EXAMPLE 2-61 s howkeyswitch Example Showing the Keyswitch Set to Standby schostname : A> showkeyswitch key switch is: standby
112 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
showlogs
Displays the system controller logged events stored in the system controller message buffer.
Scope platform shell, domain shell
Syntax for the Platform Shell showlogs [-d domain ID ] [-v] showlogs -h
Syntax for the Domain Shell showlogs [-v] showlogs -h
Options/Parameters
-h displays help for this command.
-d domainID (platform shell only) specifies a domain ( a , b , c , or d ).
-v is verbose.
Description
Displays the system controller logged events stored in the system controller message buffer. There is a specific log for each domain and the platform shell. If the loghost has been configured with setupplatform or setupdomain , messages will also be logged to the syslog host.
Chapter 2 System Controller Alphabetical Command Reference 113
See Also setupdomain
Examples
The examples for this command are very verbose and difficult to incorporate.
Therefore, examples are not included.
114 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
showplatform
This command displays all configuration variables for this platform.
Scope platform shell
Syntax showplatform [-v] [-d domainID ] [-p part ] showplatform -h
Options/Parameters
-h displays help for this command.
-d domainID specifies a domain to show ( a , b , c , or d ).
-p part displays information on a specific part.
where:
■
■
■
■
■
■
■
■ acls shows the Access Control List (ACL).
loghosts shows log hosts.
mac shows the mac addresses, hostID, and the platform a serial number network displays the network settings.
partition shows the partition mode.
sc shows the system controller configuration.
snmp shows snmp information.
status displays domain status
v is verbose mode.
Chapter 2 System Controller Alphabetical Command Reference 115
Description
■
■
■
■
■
■
■
This command displays all configuration variables for this platform, including:
Network attributes of the platform
ACLs for each domain
Domain status
SNMP information
Loghosts
Partition configuration
Mac address, host ID, and newly added system serial number
See Also
,
Example
CODE EXAMPLE 2-62 showplatform Output for a Sun Fire 6800 System schostname : SC> showplatform schostname :SC> showplatform
B
C
D
Domain Solaris Nodename Domain Status Keyswitch
-----------------------------------------
A Powered Off off
-
-
-
Powered Off
Powered Off
Powered Off standby off off
The system controller is configured to be on a network.
Network settings: DHCP
Hostname: hostname
IP Address: xxx.xxx.xxx.xx
Netmask: xxx.xxx.xxx.x
Gateway: xxx.xxx.xxx.xx
0
DNS Domain:
Primary DNS Server: xxx.xxx.x.xxx
Secondary DNS Server: xxx.xxx.x.xxx
Loghost for Platform:
Loghost for Domain A:
116 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
CODE EXAMPLE 2-62 showplatform Output for a Sun Fire 6800 System (Continued)
Loghost for Domain B:
Loghost for Domain C:
Loghost for Domain D:
SNMP Agent: enabled
Chassis Description: Sun Fire 6800
Chassis Contact:
Chassis Location:
Trap Hosts:
Public Community String: P-public
Private Community String: P-private
ACL for Domain A: SB0 SB1 SB2 SB3 SB4 SB5 IB6 IB7 IB8 IB9
ACL for Domain B: SB0 SB1 SB2 SB3 SB4 SB5 IB6 IB7 IB8 IB9
ACL for Domain C: SB0 SB1 SB2 SB3 SB4 SB5 IB6 IB7 IB8 IB9
ACL for Domain D: SB0 SB1 SB2 SB3 SB4 SB5 IB6 IB7 IB8 IB9
SC POST diag Level: off
Chassis is in dual partition mode.
schostname : SC>
shows the showplatform -v command output.
CODE EXAMPLE 2-63 showplatform -v Output for a Sun Fire 6800 System schostname : SC> showplatform -v schostname :SC> showplatform
B
C
D
Domain Solaris Nodename Domain Status Keyswitch
-----------------------------------------
A Powered Off off
-
-
-
Powered Off
Powered Off
Powered Off standby off off
Network
-------
The system controller is configured to be on a network.
Network settings: DHCP
Hostname: hostname
IP Address: xxx.xxx.xxx.xx
Netmask: xxx.xxx.xxx.x
Chapter 2 System Controller Alphabetical Command Reference 117
CODE EXAMPLE 2-63 showplatform -v Output for a Sun Fire 6800 System (Continued)
Gateway: xxx.xxx.xxx.xx
0
DNS Domain:
Primary DNS Server: xxx.xxx.x.xxx
Secondary DNS Server: xxx.xxx.x.xxx
Domain A
Domain B
Domain C
Domain D
SSC0
SSC1
MAC Address
----------xx:xx:xx:xx:xx:xx xx:xx:xx:xx:xx:xx xx:xx:xx:xx:xx:xx xx:xx:xx:xx:xx:xx xx:xx:xx:xx:xx:xx xx:xx:xx:xx:xx:xx
Platform Serial Number: xxxxxxxx
Loghosts
--------
Loghost for Platform:
Loghost for Domain A:
Loghost for Domain B:
Loghost for Domain C:
Loghost for Domain D:
HostID
-----xxxxxxxx xxxxxxxx xxxxxxxx xxxxxxxx xxxxxxxx xxxxxxxx
SNMP
----
SNMP Agent: enabled
Chassis Description: Sun Fire 6800
Chassis Contact:
Chassis Location:
Trap Hosts:
Public Community String: P-public
Private Community String: P-private
SNMP packets received: x
SNMP packets sent: xxx
SNMP traps sent: xxx
ACLs
----
ACL for Domain A: SB0 SB1 SB2 SB3 SB4 SB5 IB6 IB7 IB8 IB9
ACL for Domain B: SB0 SB1 SB2 SB3 SB4 SB5 IB6 IB7 IB8 IB9
ACL for Domain C: SB0 SB1 SB2 SB3 SB4 SB5 IB6 IB7 IB8 IB9
ACL for Domain D: SB0 SB1 SB2 SB3 SB4 SB5 IB6 IB7 IB8 IB9
SC POST
118 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
CODE EXAMPLE 2-63 showplatform -v Output for a Sun Fire 6800 System (Continued)
-----
SC POST diag Level: off
Partition Mode
--------------
Chassis is in dual partition mode.
schostname : SC>
TABLE 2-29 Definitions of Headings for Status of All Domains in
Headers for
Description
Domain
Solaris Nodename
Domain Status
Keyswitch
Displays domains A through D. See domain in the Glossary.
Contains the nodename of the domain (if the Solaris operating environment is running or has run since the last reboot of the system controller). Displays a dash ( – ) if the host name is not available.
Displays the domain state. The major values are: Powered off,
Active-Solaris, Active-OpenBoot PROM, Active-Booting, Running
POST, Standby, and Powered off.
Displays the keyswitch position (off, standby, on, diag, secure).
Chapter 2 System Controller Alphabetical Command Reference 119
showsc
Displays the uptime and version information about the system controller.
Scope platform shell
Syntax showsc [-h][-v]
Options/Parameters
-h displays help for this command.
-v is verbose mode.
Description
Displays the version and uptime information for the system controller.
See Also
Example
CODE EXAMPLE 2-64 showsc Command schostname : SC> showsc
SC date: Wed Sep 06 05:45:57 PDT 2001
SC uptime: 29 seconds
ScApp version: 5.11.3
RTOS version: 17
RTOS is the Real Time Operating System for the system controller.
120 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
testboard
Tests the CPU/Memory board name you specify at the command line.
Scope platform shell, domain shell
Syntax testboard board_name testboard -h
Options/Parameters
-h displays help for this command.
board_name for the CPU/Memory board is SB0 – SB5 .
Description
Tests the CPU/Memory board name you specify at the command line. The board status must be either Available or Assigned and the board must be powered on. To display the board status, use the showboards command. For more information on
board status, see “Board States” on page 19. In order for the
testboard command to run, the board in a domain must be assigned to the domain and/or be in the
Access Control List (ACL). Also, sufficient Repeater boards must be powered on.
The testboard command runs tests at the levels set in the domain. Testing a
CPU/Memory board is most accurately done when it is part of a domain. It is best if the board can be tested by POST. However, if that is not possible, testing a
CPU/Memory board in the domain is the next best test.
Testing a CPU/Memory board in a domain has a very slight possibility to cause problems in the domain. If that is the case, test the board in the platform shell in order to keep it isolated from the domain.
See Also showcomponent, showboards
Chapter 2 System Controller Alphabetical Command Reference 121
Example
To test CPU/Memory board, sb0 in the domain A shell, type:
TABLE 2-30 testboard Example Testing CPU/Memory Board 0 schostname : A> testboard sb0
122 Sun Fire 6800/4810/4800/3800 System Controller Command Reference Manual • April 2001
Download
Link público atualizado
O link público para seu chat foi atualizado. Você pode visualizar e gerenciar seus links de chat após o registro aqui.
Link público do documento
Anúncio