advertisement
Air Conditioner Features
ELECTRONIC CONTROL
Before you begin, thoroughly familiarize yourself with the control panel and remote as shown below and all its functions, then touch the symbol pads for the functions you desire. The unit can be controlled by the panel touch pads or with the remote control.
REMOTE
SENSlNG lNDlCATOR
DISPLAYS
TEMPERATURE/TIME INFRARED
REMOTE WINDOW
FILTER RESET
BUTTON
ACTIVATES
TIMER
SETS MODE
TURNS UNIT
ON OR OFF
ADJUSTS
TEMPERATURE
OR TIME
SLEEP MODE
SETS FAN SPEEDS
TOUCH PAD
REMOTE CONTROL
ON/OFF
ADJUSTS
TEMP &
TIME
SETS
MODE
ACTIVATES
REMOTE
SENSING
LlGHT
SETS FAN
SPEEDS
ACTIVATES
TIMER
Battery Size: AAA, Qty.: 2
WARNING: Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable
(nickel-cadmium) batteries.
5
Air Conditioner Features
(continued)
Note: The following instructions describe the Control Panel Touch Pads. The same instructions apply to the
Remote Control.
To turn unit on or off press the ON/OFF button:
Note: The unit is programmed to start in the cool mode, with high fan speed and a temperature setting of 72 °F.
To use Cool, press the MODE button to select:
To change the Temperature Setting use the UP and Down arrows as required:
To adjust Fan Speeds press the Fan Speed button and select:
LOW MED HIGH
To use the Auto Fan Feature press the Fan Speed button and select AUTO:
Note: Fan speed starts at high and adjusts to a slower speed as the room temperature dictates. For example, if the room doesn’t get too warm it will stay at the slowest speed.
If the room temperature rises quickly, such as when a door is opened, it will automatically go to the highest speed. The fan speed will re-adjust back to the slowest speed as the room returns to the original set temperature.
To operate on Fan Only, press the MODE button to select:
Use Fan Only function to circulate room air without air conditioner cooling. You can use any fan speed you prefer and the actual room temperature will be displayed in the
DISPLAY.
6
Air Conditioner Features
(continued)
To use Energy Saver press the MODE button to select:
You will save energy usage in this mode. The compressor and motor will turn off once the room is at the desired temperature. The air will be sampled for 20 seconds every
10 minutes until the room is above the set temperature, at which point the compressor turns back on and the fan runs. The entire process is now repeated.
To use the Sleep feature press the SLEEP button and the LED will illuminate:
The set temperature will increase 2 °F 30 minutes after this mode is selected. It will increase again after 30 minutes by another 2 °F. It will stay at this set point for 7 hours, and then return to the original setting.
To use the Timer function press the TIMER button and the LED will illuminate:
Press the UP and DOWN arrows to select the desired time up to 24 hrs. The control will count down the time remaining in 1 and 0.5 hr increments. If you need to change the set temperature, press MODE then the UP/DOWN arrows. Then after 5 seconds the display will revert to the hours remaining. This mode can be cancelled by pressing the TIMER button. The mode will operate one time, then the above steps have to be repeated.
NOTE: Timer button is functional when On/Off button is set to either On or Off. When set to On, the amount selected is the time remaining until the unit shuts Off. When set to Off, the amount is the time until the unit turns On.
Check Filter Feature:
After 250 hours of operation, the Filter Reset LED will light. This is a reminder to clean the filter housed behind the front panel to keep the unit operating efficiently. Pressing the
FILTER RESET button for 3 seconds will reset this reminder and turn off the LED.
Remote Sensing Feature:
LIGHT pulsing ( On & Off intermittently ).
PRESS REMOTE
SENSING START BUTTON
Remote Sensing allows you to transmit the room temperature and desired coolness setting from where you sit to the air conditioner. The air conditioner then cools the area where you sit to your desired coolness setting.
Note: This feature can be activated from the remote control ONLY, and the unit must be in a cooling mode.
To activate the remote sensing feature, point the remote control towards the unit and press the remote sensing Start button. Next, use the “ ” buttons to set the desired room temperature with the remote. (Note that the set temperature will only be displayed on the unit itself ). The LIGHT on the unit control will pulse to indicate it received the signal. The LIGHT on the remote control will pulse each time it sends a signal. lt will periodically send this signal until the feature is deactivated by pressing the remote sensing Stop button. lf the unit does not receive the remote sensing signal during any 200 second interval, the unit will beep to indicate the remote sensing mode has ended. The display on the remote control indicates the temperature at the remote ONLY.
NOTE: The Remote Sensing function is terminated either by using the
Remote Sensing Stop button or the main ON/OFF button on the unit.
7
advertisement