7.8 TIRES. Scag Power Equipment SFW36-16BV, SFW48-16BV, GC-4D, SFW Belt Drive
Add to My manuals48 Pages
advertisement
![7.8 TIRES. Scag Power Equipment SFW36-16BV, SFW48-16BV, GC-4D, SFW Belt Drive | Manualzz 7.8 TIRES. Scag Power Equipment SFW36-16BV, SFW48-16BV, GC-4D, SFW Belt Drive | Manualzz](http://s2.manualzz.com/store/data/062144248_1-c4fbd8b75ff953923d9689e7c3f1dc4a-360x466.png)
R
Section 7 sharpened. Remove the blades for sharpening. See
"Blade Replacement."
- NOTE -
Keep the blades sharp. Cutting with dull blades not only yields a poor mowing job, but slows the cutting speed of the mower and causes extra wear on the engine and the blade drive by pulling hard.
B. BLADE SHARPENING
- NOTE -
If possible, use a file to sharpen the blade. Using a wheel grinder may burn the blade.
2. Raise the mower deck to the highest position. Place the lanyard pin in the highest cutting height position to prevent the cutter deck from falling.
3. Secure the cutter blades to prevent them from rotating, (use the optional Blade Buddy tool P/N
9212, to assist in securing the cutter blades), remove the blade attaching bolt. Remove the cutter blade, bolt, lockwasher and flatwasher from the spindle shaft. See Figure 7-4.
- NOTE -
Be sure that the blade is installed with the lift wing towards the top of the cutter deck.
4. Install the cutter blade on to the cutter spindle shaft.
Secure the blades from rotating and torque to
75 ft/lbs. See Figure 7-4.
- NOTE -
DO NOT sharpen the blades beyond 1/3 of the width of the blade. See Figure 7-3.
1. Sharpen the cutting edge at the same bevel as the original. See Figure 7-3. Sharpen only the top of the cutting edge to maintain sharpness.
Angle Blade Back
Do Not Cut In
CUTTER BLADE
LOCKWASHER x
30
X Must NOT Exceed
1/3 Blade Width
SGB033
2.
Figure 7-3. Blade Sharpening
Check the balance of the blade. If the blades are out of balance, vibration and premature wear can occur.
See your authorized Scag dealer for blade balancing or special tools, if you choose to balance your own blades.
C. BLADE REPLACEMENT
5/8-11 x 1-1/2" HEX HEAD BOLT
TORQUE TO 75 FT/LBS
FLATWASHER
7.8 TIRES
Figure 7-4. Blade Replacement
Check the tire pressures after every 8 hours of operation or daily.
Caster Wheels
Drive Wheels
25 PSI
12 PSI
WARNING
Always wear proper hand and eye protection when working with cutter blades.
1. Remove the ignition key before replacing the blades.
26
advertisement
Related manuals
advertisement
Table of contents
- 5 1.1 INTRODUCTION
- 5 1.2 DIRECTION REFERENCE
- 5 1.3 SERvICING THE ENGINE AND DRIvE TRAIN COMPONENTS
- 6 1.4 SYMBOLS
- 7 2.1 INTRODUCTION
- 7 2.2 SIGNAL WORDS
- 7 2.3 BEFORE OPERATION CONSIDERATIONS
- 8 2.4 OPERATION CONSIDERATIONS
- 9 2.5 MAINTENANCE CONSIDERATIONS & STORAGE
- 10 2.6 USING A SPARk ARRESTOR
- 11 2.7 SAFETY AND INSTRUCTIONAL DECALS
- 12 3.1 ENGINE
- 12 3.2 ELECTRICAL
- 12 3.3 ENGINE DECk
- 12 3.4 CUTTER DECk
- 13 3.5 WEIGHTS AND DIMENSIONS
- 13 3.6 PRODUCTIvITY
- 14 4.1 CONTROLS AND INSTRUMENT IDENTIFICATION
- 15 4.2 SAFETY INTERLOCk SYSTEM
- 15 4.3 INITIAL RUN-IN PROCEDURES
- 15 4.4 STARTING THE ENGINE
- 16 4.5 GROUND TRAvEL AND STEERING
- 17 4.6 ENGAGING THE DECk DRIvE (CUTTER BLADES)
- 17 4.7 HILLSIDE OPERATION
- 17 4.8 PARkING THE MOWER
- 18 4.9 AFTER OPERATION
- 18 4.10 REMOvING CLOGGED MATERIAL
- 18 4.11 MOvING MOWER WITH ENGINE STOPPED
- 18 4.12 RECOMMENDATIONS FOR MOWING
- 19 4.13 ADJUSTING CUTTING HEIGHT
- 23 6.1 DRIvE CONTROL ADJUSTMENTS
- 23 6.2 THROTTLE CONTROL AND CHOkE ADJUSTMENTS
- 23 6.3 BELT ADJUSTMENT
- 23 6.4 BELT ALIGNMENT
- 23 6.5 CUTTER DECk ADJUSTMENTS
- 24 6.6 ELECTRIC CLUTCH ADJUSTMENT
- 26 7.1 MAINTENANCE CHART - RECOMMENDED SERvICE INTERvALS
- 27 7.2 LUBRICATION
- 28 7.3 ENGINE OIL
- 28 7.4 ENGINE FUEL SYSTEM
- 29 7.5 ENGINE AIR CLEANER
- 29 7.6 DRIvE BELTS
- 29 7.7 CUTTER BLADES
- 30 7.8 TIRES
- 31 8.1 SCAG APPROvED ATTACHMENTS AND ACCESSORIES
- 32 36" CUTTER DECk
- 34 48" CUTTER DECk
- 36 CUTTER DECk CONTROLS
- 38 HANDLE ASSEMBLY
- 40 ENGINE DECk
- 42 ELECTRICAL SYSTEM AND THROTTLE CONTROL
- 44 REPLACEMENT DECALS AND INFORMATION PLATES
- 46 SFW ELECTRICAL SCHEMATIC