advertisement
▼
Scroll to page 2
of
126
AA G701 - EN.book Page 26 Monday, March 17, 2003 4:24 PM
26 2 System setup
Network connection
The server has two Local Area Network (LAN) ports, both located on the rear panel, a 10/100/1000 Mbps Gigabit LAN port suitable for fast network connection and a 10 Mbps RDM LAN port for remote server management.
To connect to the network, simply plug the network cable into the
Gigabit LAN port (gray port).
Note: The illustration below shows the Altos G701 server chassis.
Note: Consult the operating system manual for information on how to configure the network setup.
advertisement
Related manuals
advertisement
Table of contents
- 3 Notices
- 3 FCC notice
- 4 Laser compliance statement
- 5 Important safety instructions
- 11 1 System tour
- 13 Features summary
- 14 External and internal structure
- 14 Front bezel
- 15 Front panel
- 17 Rear panel
- 19 Internal components
- 20 System boards
- 20 Mainboard layout
- 24 Hot-swap HDD Cage layout
- 25 2 System setup
- 27 Setting up the system
- 27 Preinstallation requirements
- 28 Connecting peripherals
- 28 Connecting the PS/2 keyboard
- 29 Connecting the PS/2 mouse
- 30 Connecting the VGA monitor
- 31 Connecting a printer
- 32 Connecting the power cable
- 33 Turning on the system
- 34 Power-on problems
- 35 Operating system configuration
- 36 Network connection
- 37 Tower-to-rack option
- 38 Turning off the system
- 39 3 Upgrading the system
- 41 Upgrading the system
- 41 Installation precautions
- 43 Opening the server
- 43 Opening the front bezel
- 43 Removing the front bezel
- 44 Removing the side panel
- 45 Removing the air baffle
- 47 Configuring the hot-swappable cage
- 47 Removing the hot-swappable cage
- 48 Installing a hard disk into the hot-swappable cage hard disk carrier
- 50 Installing the hot-swappable cage
- 51 Installing and removing storage devices
- 51 Replacing the 3.5-inch floppy drive
- 54 Installing a 5.25-inch storage device (optional)
- 56 Upgrading the CPU
- 56 To remove a CPU with heatsink
- 57 To install a CPU with heatsink
- 58 Upgrading the system memory
- 58 To remove a DIMM
- 59 To install a DIMM
- 60 Installing an expansion card
- 60 To install an expansion card
- 62 Installing a redundant power supply module
- 63 To install a redundant power supply module
- 65 Installing a hot-swappable HDD fan
- 65 To remove a hot-swappable HDD fan
- 66 To install a hot-swappable HDD fan
- 67 4 BIOS setup
- 69 BIOS setup
- 70 Entering BIOS setup
- 72 Main
- 74 System Information
- 76 Advanced
- 77 Super I/O Configuration
- 78 IDE Configuration
- 81 Floppy Configuration
- 82 PCI/PnP Configuration
- 84 Boot Settings Configuration
- 87 Event Log Configuration
- 89 Onboard Devices Configuration
- 90 Remote Access
- 91 Power
- 93 Boot
- 94 Boot Device Priority
- 95 Hard Disk Drives
- 96 Removable Devices
- 97 ATAPI CD-ROM Drives
- 98 Security
- 99 To set a Supervisor/User password
- 99 To change the Supervisor/User password
- 99 To remove the User password
- 100 Exit
- 103 Appendix A ASM & RDM quick installation guide
- 105 Installing ASM
- 105 System requirements
- 106 System setup
- 108 Installing RDM
- 108 System requirements
- 108 RDM Console setup
- 111 Appendix B Rack installation guide
- 113 System rack installation
- 114 Vertical mounting hole pattern
- 115 Screw types for rack installation
- 116 Installing cage nuts
- 117 Installing the system into the rack
- 125 Index