advertisement
Code Identification
Code Identification
1. Press and hold Code Search button until the red indicator stays on. Release the Code Search button.
2. Press and release the desired mode button (TV, VCR, etc.).
The red indicator blinks, then stays lit.
3. Press and release the Code Search button. The indicator light blinks off.
4. To find the first digit for the code stored under the mode key pressed in step 2, press each numeric key from 0-9 in turn.
When the indicator light blinks off the number you pressed is the first digit for the code you are searching for.
5. To find the second digit, repeat step 4, this time when the indicator light blinks off this is the second digit.
6. Repeat step 4 again to find the third digit.
The Sleep feature enables the remote to turn off the TV after a period of 1 to 99 minutes. Remote is to be in TV mode to set a
Sleep Timer. This feature works even if your TV does not have this feature.
2.
Sleep Timer
1. Press and release the TV Mode key.
2. Press and hold the Sleep button until LED remains on (occurring after approx. 2-3 seconds).
3. Release Sleep button.
4. Press and release the numeric keys (01-99) for the time required. The LED will blink off to indicate keypress acceptance and remain off after second keypress.
5. TV Sleep Timer now set.
6. Leave the Remote pointing towards the TV with an unobstructed path.
To cancel the Sleep Timer, press and hold the Sleep key until the
LED blinks or press and release the Power key in TV Mode.
1, 3.
4.
IN FO/
SEL ECT
GU IDE
Code Learning
Tips On Learning
1. Use fresh batteries for both the Learning Remote and the
Original Remote.
2. Perform a Master clear (see page 15) before learning.
3. Place the original remote end-to-end with the Learning Remote so the IR transmitters on both remotes are directly in line with each other. Keep the two remotes approximately one inch away from each other.
4. Experiment by learning 2 or 3 commands initially (to ensure compatibility and familiarity) and then carry out a Master Clear before completely learning your original remote’s commands.
5. Do not try to learn directly under an incandescent or lowenergy light as these can cause interference with learning. Keep at least three feet away from any such light sources.
12 13
Code Learning, cont.
Learning Commands
1. Press and hold the Code Search button until the red indicator stays on. Release the Code Search button.
2. Press the mode button for the type of device you want to learn
(TV, VCR, Cable, etc.). The indicator lights blinks off once.
3. Press the Learn button.
4. Press the button on the Learning Remote that you want to teach, e.g. Power.
5. Point both remotes at each other (see tips on page 11). Press and hold the Original Remote button that you want to learn, e.g. Power, until the indicator light turns off. If there is a problem with learning, the indicator light blinks for three seconds but the remote remains in the Learning mode. If this happens, repeat from Step 4.
6.. Repeat Steps 4 and 5 for other buttons you want to learn.
7. Press and release the Code Search button when all desired original remote commands are learned. Code Learning is now complete.
Note :- No functions may be stored under the Code Search button, any mode button, AUX button, or the Learn button.
Code Learning, cont.
To Clear all Learned Commands under a mode
1. Press and hold the Code Search button until the indicator light turns on. Release the Code Search button.
2. Press and release the button for the mode you want to clear
(TV, VCR, etc.). The indicator blinks off.
3. Press and release the Learn button TWICE. The indicator blinks off.
4. Press and release Code Search. The indicator blinks off.
All learned Commands under that mode are now cleared.
2.
1, 4.
3.
5.
Approx. 1 inch apart
Master Clear - To Clear all Learned Commands, i.e.
return to factory defaults
1. Press and hold the Code Search button until the indicator light turns on. Release the Code Search button.
2. Press and release the Learn button TWICE. The indicator blinks off.
3. Press and release Code Search. The indicator blinks off.
All Learned commands in the remote are now cleared.
2.
1.
4.
1, 3.
3.
2.
14 15
advertisement