Setup Using Front Panel. Generac Power Systems QT15068KNSNR, QT05554ANANR, QT15068KNSN, 100kW QT10054ANSNR, 55 kW QT05554ANANR, QT10068JNAN, QT13068GNSNR, 150kW QT15068KNSN, 100kW QT10068JNAN, H-100

General Information

H-100 Control Panel Technical Manual

QUIETTEST

®

SETUP USING FRONT

PANEL

Press the “MENU” button.

Select the time of day to run exercise.

Move the cursor using the arrow keys to the Exercise/

HTS menu item.

Press the “ENTER” button.

Verify “QuietTest®” is not checked. Press “Apply”.

Setup of Normal exercise is now complete. For this example, exercise will start every Wednesday at 10:30

AM and run until about 10:50 AM

If exercise of the HTS is desired, Click on “Transfer on exercise” to enable transferring of the load to the generator during exercise.

NOTE:

This feature is only available in non-QuietTest® exercise and when an HTS is in the system.

Move the cursor to the “Exercise Enabled” field on the first line.

Press the “ENTER” button to enter edit mode.

27

General Information

H-100 Control Panel Technical Manual

Use the up and down arrow keys until a “Y” appears in the field.

Press the "ENTER" button to exit edit mode.

Press the “ENTER” button to exit edit mode.

Move the cursor to the “Time Start” time of day hours field on the second line.

Move the cursor to the “Time Start” day of week field on the second line.

Press the “ENTER” button to enter edit mode.

Press the “ENTER” button to enter edit mode.

Use the up and down arrow key until the desired hour of the day is displayed.

NOTE:

In a number field the up/down arrows move the digit up and down while the left/right arrows move to the adjacent digit.

Use the up and down arrow key until the desired day of the week is displayed.

Press the “ENTER” button to exit edit mode.

28

Move the cursor to the “Time Start” time of day minutes field on the second line.

General Information

H-100 Control Panel Technical Manual

Press the “ENTER” button to enter edit mode.

Move the cursor to the “QuietTest Selected” field on the first line.

Use the up and down arrow key until the desired minute of the hour is displayed.

Press the “ENTER” button to enter edit mode.

Use the up and down arrow key until a “Y” appears.

Press the “ENTER” button to exit edit mode.

Press the “ENTER” button to exit edit mode.

Move the cursor to the

 on the bottom line.

Press the “ENTER” button to move to the second page.

NOTE:

Verify that “Xfer On Exercise” field is an “N”.

Otherwise, QuietTest® will be overridden with normal exercise.

29

General Information

H-100 Control Panel Technical Manual

Setup of QuietTest® is now complete. For this example, QuietTest® will start every Wednesday at 10:30

AM and run until about 10:50 AM

While QuietTest® is running, the “Time Remaining” will display the approximate number of minutes left before QuietTest® is completed.

Press the “ENTER” button to enter edit mode.

NORMAL EXERCISE SETUP USING

FRONT PANEL

Press the “MENU” button.

Use the up and down arrow keys until a “Y” appears in the field.

Move the cursor using the arrow keys to the Exercise/

HTS menu item.

Press the “ENTER” button to exit edit mode.

Press the “ENTER” button.

Move the cursor to the “Time Start” day of week field on the second line.

Move the cursor to the “Exercise Enabled” field on the first line.

Press the “ENTER” button to enter edit mode.

30

General Information

H-100 Control Panel Technical Manual

NOTE:

In a number field the up/down arrows move the digit up and down while the left/right arrows move to the adjacent digit.

Use the up and down arrow key until the desired day of the week is displayed.

Press the “ENTER” button to exit edit mode.

Press the "ENTER" button to exit edit mode.

Move the cursor to the “Time Start” time of day minutes field on the second line.

Move the cursor to the “Time Start” time of day hours field on the second line.

Press the “ENTER” button to enter edit mode.

Press the “ENTER” button to enter edit mode.

Use the up and down arrow key until the desired minute of the hour is displayed.

Use the up and down arrow key until the desired hour of the day is displayed.

31

General Information

H-100 Control Panel Technical Manual

Press the “ENTER” button to exit edit mode.

Use the up and down arrow key until a “N” appears.

Move the cursor to the

 on the bottom line.

Press the “ENTER” button to exit edit mode.

Press the “ENTER” button to move to the second page.

Setup of Normal Exercise is now complete. For this example, exercise will start every Wednesday at 10:30

AM and run until about 10:50 AM

While normal exercise is running, the “Time

Remaining” will display the approximate number of minutes left before exercise is completed.

Move the cursor to the “QuietTest Selected” field on the first line.

If it is desired to exercise the HTS as well during the exercise cycle, then continue with the enabling of

“transfer on exercise” described below.

Move the cursor to the “Xfer On Exercise” field on the third line.

Press the “ENTER” button to enter edit mode.

Press the “ENTER” button to enter edit mode.

32