![](http://s2.manualzz.com/store/data/066115736_1-b20765ffcc6d049b9fa6272fb9e74a8c-128x128.png)
Appendix. AxleTech PSC1764, PSC822, PSS165, PSC205, PSC1485, PSC1614, PSC826, PSC1875, PSC824, PSS166
Add to My manuals38 Pages
advertisement
![Appendix. AxleTech PSC1764, PSC822, PSS165, PSC205, PSC1485, PSC1614, PSC826, PSC1875, PSC824, PSS166 | Manualzz Appendix. AxleTech PSC1764, PSC822, PSS165, PSC205, PSC1485, PSC1614, PSC826, PSC1875, PSC824, PSS166 | Manualzz](http://s2.manualzz.com/store/data/066115736_1-b20765ffcc6d049b9fa6272fb9e74a8c-360x466.png)
Appendix
Torque Specifi cations
Appendix
24
Appendix
25
Appendix
Torque Values for Fasteners
1. The torque values in the previous tables are for fasteners with a light application of oil on the threads.
2. If the fasteners are dry, increase the torque values by ten percent (10%).
3. If the fasteners have a heavy application of oil on the threads, decrease the torque values by ten percent
(10%).
4. If the size of the fastener being installed is unknown, measure the fastener using the procedures in the following section.
5. Compare the size of fastener measured in Step 4 to the list of fasteners in tables to fi nd the correct torque value.
Measuring American Standard Fasteners
Measuring Metric Fasteners
Y Dimension
(Distance of
10 Threads)
Number of Threads in 1”
X Dimension
(For example
M8 or 8mm) a. Measure the diameter of the threads in millimeters (mm), dimension X.
b. Measure the distance of ten (10) threads, point to point in millimeters (mm), dimension Y.
Make a note of dimension Y.
c. Divide dimension Y by ten (10). The result will be the distance between two threads or pitch.
Example:
Metric size fastener is M8 x 1.25.
• M8 is the diameter of the fastener in millimeters (mm) or dimension X
• 1.25 is the distance between two threads or pitch
X Dimension
(For example 1/2”) a. Measure the diameter of the threads in inches, dimension X.
b. Count the amount of threads there are in 1”.
Example:
American Standard size fastener is 0.50-13.00.
• 0.50 is the diameter of the fastener in inches or dimension X
• 13.00 is the amount of threads in 1”
26
Customer Service
877-547-3907
+33 (0) 4 77 92 88 92
Customer Service Fax
877-547-3987
Aftermarket: [email protected]
© 2018 AxleTech International LLC. All rights reserved. AxleTech and AxleTech International are registered trademarks of AxleTech International LLC.
All other brands and product names are trademarks or registered trademarks of their respective owners. Information supplied by AxleTech is believed to be accurate and reliable. AxleTech reserves the right, without notice, to makes changes in product design or specifications.
www.axletech.com
ASM-0910E 10/19
advertisement
Related manuals
advertisement
Table of contents
- 2 Table of Contents
- 3 Service Notes
- 4 Asbestos & Non-Asbestos Fibers Warning
- 6 Service Precautions
- 9 General Assembly Instructions
- 12 Introduction
- 12 Description
- 13 Axle Designs Covered in This Manual
- 13 Axle Designs Not Covered in This Manual
- 13 Identification Tag
- 13 Model Nomenclature
- 14 Exploded Views
- 16 Removal and Disassembly
- 16 Axle Shaft Assembly Removal
- 16 Steer Knuckle Removal
- 19 King Pin Bushing Inspection
- 19 Non-Sealed King Pin Bushings
- 19 Sealed King Pin Bushings
- 20 Axle Shaft Oil Seal and Bushing
- 20 Disassembly
- 20 Steering Universal Joint
- 20 Wing Bearing Yokes
- 21 Round Bearing Yokes or Cardan Joint
- 22 Constant Velocity Joint
- 22 Preparing Parts for Assembly
- 22 Cleaning
- 23 Parts Inspection
- 23 Flush Lubricant From the Axle Housing
- 23 Assembly and Installation
- 23 Assembly of Steering Universal Joint
- 23 Round Bearing Yokes or Cardan Joint
- 24 Wing Bearing Yokes
- 24 Constant Velocity Joint
- 25 Installation of Axle Shaft Bushing & Seal
- 26 Installation of King Pin Bushings
- 26 Non-Sealed King Pin Bushings
- 27 Sealed King Pin Bushings
- 28 Assembly of Steer Knuckle
- 29 Non-Sealed King Pin Bushing
- 29 Sealed King Pin Bushing
- 29 Steer Knuckle Adjustment
- 29 Feeler Gauge Method
- 30 Dial Indicator Method
- 30 Adjust Knuckle Vertical End Play
- 31 Final King Pin Cap Installation
- 31 Sealed King Pin
- 31 Non-Sealed King Pin
- 32 Axle Components
- 32 Axle Shaft & Universal Joint
- 32 Spindle, Brake, & Planetary Wheel End
- 33 Torque Specifications
- 34 Lubrication Specifications
- 35 Appendix
- 35 General Torque Specifications
- 37 Torque Values for Fasteners
- 37 Measuring American Standard Fasteners
- 37 Measuring Metric Fasteners