More
Do Not Disturb
Swipe down on the device's home screen and touch to enable Do Not Disturb.
Alternatively, enter the app list, go to Settings > Do Not Disturb, and schedule a period for this mode.
After Do Not Disturb is enabled:
•
•
The device will not ring or vibrate to notify you of incoming calls or notifications, and the Raise to wake feature will be disabled.
The alarm will vibrate and ring as normal.
Adding custom cards
1 Go to Settings > Custom cards or Settings > Display > Favorites.
2 Touch , and select the cards to be displayed, such as the Sleep, Stress, and Heart rate cards. The actual display prevails.
3 Touch next to a card that you have added, or touch and hold the card to move it to another position (supported on some device models). Touch to delete the card.
4 After the settings are complete, swipe left or right on the home screen to view the added cards.
Adjusting and replacing the strap
Adjusting the strap length
The silicone strap and leather strap are designed with horseshoe buckles, and the metal strap is designed with a dual magnetic clasp. You can adjust the strap based on your wrist circumference, so that it fits comfortably.
•
Removing and installing the strap
Strap 1: Active Edition
30
More
1: Superfit button
Remove the strap: Press the superfit button on each end of the watch body to separate the strap from the watch body.
•
Install the strap: Align the strap with the watch body and fasten it.
Separately purchased links are required for replacing the silicone strap of the Active
Edition with a leather or metal strap.
Strap 2: Classic Edition
1: Link 2: Superfit button 3: Springbar lever
31
More
Remove the links: Press the superfit button on each end of the watch body to separate the links from the watch body.
Install the links: Align the links with the watch body and fasten them.
Remove the strap: Push the springbar lever on the strap, tilt the strap outwards and remove it from the link fixing slot.
•
Install the strap: Push the springbar lever on the strap, align the springbar pin with the link fixing slot, and install the strap.
Strap 3: Elegant Edition
32
1: Link 2: Superfit button 3: Springbar lever
More
Remove the links: Press the superfit button on each end of the watch body to separate the links from the watch body.
Install the links: Align the links with the watch body and fasten them.
Remove the strap: Push the springbar levers on the strap, tilt the strap outwards and remove it from the link fixing slot.
Install the strap: Push the springbar levers on the strap, align the springbar pin with the link fixing slot, and install the strap.
Updating the watch
Open the Huawei Health app, touch Devices and your device name, then touch Firmware
update. Your phone will then check for the available updates. Follow the onscreen instructions to complete the update.
33
More
•
•
Viewing the Bluetooth name, MAC address, SN, model, and version number
Method 1: On your device, go to Settings > About, swipe up and down to view the device name (the device Bluetooth name), MAC address, model, version number, and SN (serial number).
Method 2: Open the Huawei Health app, then touch Devices and the device name. The name of the connected device is the Bluetooth name.
Open the Huawei Health app, go to the device details screen, touch Firmware update, the
Current version is the current version number of your device.
Water and dust resistance
The device features 5 ATM water resistance, but this protection is not permanent and may reduce over time.
You can wear the device when you are washing your hands, outside in the rain, or swimming in shallow water. Do not wear it when you are showering, scuba diving, or diving.
•
•
•
The following may affect the water resistance of the device:
It is dropped, bumped, or encounters other impacts.
It comes into contact with liquids including soap, shower gel, detergent, perfume, lotion, and oil.
It is used in high-temperature and high-humidity environments including hot baths and saunas.
One-touch drainage
Swipe down from the home screen, touch , and the screen will display that it's draining water. During drainage, the device will vibrate and make a drip sound. When the drainage is about to finish, you can shake the device to speed up the drainage of water droplets from the bell mouth.
After you swim with the device, it will automatically vibrate and drain water.
Statement for devices supporting micropower frequency bands
This product supports micropower short-range radio (also referred to as NFC) specified in the
"Radio Regulations of the People's Republic of China". According to Notice No. 52, 2019
34
More issued by the Chinese Ministry of Industry and Information Technology (MIIT) on requirements for NFC:
1. The product complies with the specific clauses and application scenarios specified in the
Technical Requirements for Micropower (Short Distance) Radio Equipment, including the antenna types and performance, and usage of control, adjustment, and switches.
2. It is forbidden to change the application scenarios or conditions, expand the transmit frequency range, increase the transmit power (including installing additional RF power amplifiers), or change the transmit antenna without permission.
3. The product shall not cause harmful interference to other legal radio stations, and requests for protection against harmful interference shall not be proposed.
4. The product shall withstand interference from industrial, scientific, and medical (ISM) devices that radiate radio frequency energy or other legal radio stations.
5. If the product causes harmful interference to other legal radio stations, stop using it immediately and take measures to eliminate the interference before continuing to use it.
6. The use of civil and military radio stations such as radio astronomy stations, meteorological radar stations, and satellite earth stations (including measurement and control stations, ranging stations, reception stations, and navigation stations) inside aircraft and in accordance with laws and regulations, relevant national regulations, and standards, as well as the use of micropower equipment in the electromagnetic environment protection areas such as airports, shall comply with the regulations of the electromagnetic environment protection and relevant industry administrative departments.
7. It is forbidden to use model remote controls in an area with a radius of 5,000 meters centered on the center of the airport runway.
8. Environmental conditions for the temperature and voltage of the micro-power device being used have been specified.
35
