Lubrication. Kongskilde Profiline
Add to My manuals30 Pages
Kongskilde Profiline is a seed drill that can be used for a variety of crops, including barley, wheat, peas, and rape. It has a working width of 300 cm and a hopper capacity of 741 dm3. The seed drill is equipped with a variety of features that make it easy to use and maintain, including a fine adjustment of bottom flaps, easy cleaning of seed outlets and sowing rollers, and a lubrication system that helps to keep the machine running smoothly. The Kongskilde Profiline is a versatile and reliable seed drill that can help you to get the most out of your crops.
advertisement
Maintenance and lubricating
Fine adjustment of bottom flaps
The bottom flaps should be set to the highest position
(position 1).
Adjustment can then be carried out by turning the screw on the rear face of each bottom flap until the distance between the flap and the seed roller is 1 mm. See figure
5B.
Figure 5A. Screw for adjustment of the bottom flaps.
Cleaning of seed outlets and sowing rollers
Cleaning the seed outlets and seed rollers can be facilitated by removing the sowing shaft. The sowing shaft can be disengaged by lifting the locking plates and turning it backwards. See figure 5B.
The sowing shaft can be locked again by pushing the shaft down and turning the locking plates forward and fastening them in place.
The shaft can then be lifted to check that the locking plates are locked in place.
Maintenance and lubrication
Lubrication
The gearbox oil must be visible in the sight glass, otherwise it must be refilled with one of the following types of oil:
HYDROL L-HL 60
All chains should be lubricated regularly. After each season, the chains should be cleaned in petroleum and then lubricated with oil.
Before each new season all linkages and chain tighteners should also be lubricated.
Marker arms should be regularly greased.
All bearings are self-sealed and do not require lubrication.
Winter storage
Careful cleaning of the seed drill after each season is recommended.
The machine should also be prepared before the start of the new season.
without any hurry
The seed drill should be protected from the elements during storage.
Figure 5C. Spots to be lubricated on the machine.
Figure 5B. Locking plates to sowing shaft.
22 23
advertisement
Related manuals
advertisement
Table of contents
- - Foreword
- - Technical specification
- - Equipment
- - Safety precautions
- - Commissioning
- - Tyre pressures
- - Coupling the tractor
- - Disengagement from the tractor (parking)
- - Row distance
- - Marker shifter
- - Mounting the following harrow
- - Generally
- - Calibration of the drill
- - Agitator shaft
- - Bottom flaps
- 1 Seed housing shutters
- 1 Lowering the seed funnels
- 2 Calibration tray(s) to horizontal
- 2 Scale setting
- 2 Filling of sowing material
- 2 Starting the seed flow
- 2 Turning the test sowing handle
- 3 Weighing
- 3 Calculation of the sowing rate
- 3 Adjusting the sowing rate
- 3 Sowing tray(s) closed
- 3 Raising the seed funnels
- 3 Discrepancies in the sowing rate
- 4 Special crops
- 4 Sowing of grass seed
- 4 Sowing of amall round seeds
- 4 Sowing of peas, beans, maize etc
- 5 Coulter pressure/sowing depth
- 5 Coulter tightening
- 6 Wheel track eradicators
- 7 Markers
- 7 Adjustment of markers
- 7 Centre marking
- 7 Front wheel marking
- 7 Marking track
- 8 Adjustment of following harrow
- 9 Generally
- 9 Driving speed
- 9 Emptying of seed hopper
- 10 Fine adjustment of bottom flaps
- 11 Lubrication
- 11 Winter storage
- 12 Sowing table Barley
- 13 Sowing table Wheat
- 14 Sowing table Peas
- 15 Sowing table Rape
- 2 Foreword
- 3 Technical specification
- 4 Equipment
- 5 Safety precautions
- 6 Commissioning
- 6 Tyre pressures
- 7 Coupling the tractor
- 7 Disengagement from the tractor (parking)
- 8 Row distance
- 9 Marker shifter
- 10 Mounting the following harrow
- 11 Generally
- 11 Calibration of the drill
- 11 Agitator shaft
- 11 Bottom flaps
- 12 Seed housing shutters
- 12 Lowering the seed funnels
- 13 Calibration tray(s) to horizontal
- 13 Scale setting
- 13 Filling of sowing material
- 13 Starting the seed flow
- 13 Turning the test sowing handle
- 14 Weighing
- 14 Calculation of the sowing rate
- 14 Adjusting the sowing rate
- 14 Sowing tray(s) closed
- 14 Raising the seed funnels
- 14 Discrepancies in the sowing rate
- 15 Special crops
- 15 Sowing of grass seed
- 15 Sowing of amall round seeds
- 15 Sowing of peas, beans, maize etc
- 16 Coulter pressure/sowing depth
- 16 Coulter tightening
- 17 Wheel track eradicators
- 18 Markers
- 18 Adjustment of markers
- 18 Centre marking
- 18 Front wheel marking
- 18 Marking track
- 19 Adjustment of following harrow
- 20 Generally
- 20 Driving speed
- 20 Emptying of seed hopper
- 21 Fine adjustment of bottom flaps
- 22 Lubrication
- 22 Winter storage
- 23 Sowing table Barley
- 24 Sowing table Wheat
- 25 Sowing table Peas
- 26 Sowing table Rape