Installation II Menu
To access the Installation II menu and adjust the settings, perform the following steps:
1. Enter the OSD menu.
2. Press the ◄ or ► button to select the Installation II menu.
3. Press the ▲ or ▼ button to move the cursor up or down in the Installation II menu.
ITEM
Auto Source
Auto Power Off (min)
Auto Power On
LED Mode
Advanced
Factory Reset
Status
DESCRIPTION
Press the ◄ or ► button to enable or disable automatic source detection.
Press the ◄ or ► button to automatically turn the projector lamp off when there is no signal.
Press the ◄ or ► button to enable or disable automatic power on.
Press the ◄ or ► button to select the LED mode for higher brightness or lower brightness to save LED life.
Press to enter the Advanced menu. See
Advanced Feature on page 37.
Press to reset all items to factory preset values.
Press to enter the Status menu. See page 40 for more
information on Status.
36
Advanced Feature
To access the Advanced menu and adjust the settings, perform the following steps:
1. Enter the OSD menu.
2. Press the ◄ or ► button to select the Installation II menu.
3. Press the ▲ or ▼ button to select the Advanced menu and then press .
4. Press the ▲ or ▼ button to move the cursor up or down in the Advanced menu.
5. Press the ◄ or ► button to change values for each applicable setting.
ITEM
OSD Menu Setting
Peripheral Test
3D
Low Power Mode
DESCRIPTION
Press to enter the OSD setting menu. See page 38 for more
information on OSD Menu Setting.
Press to enter the Peripheral Test menu. See page 38 for
more information on Peripheral Test.
Press to enter the 3D menu. See 3D on page 39.
Press the ◄ or ► button to enable (<1W power consumption) or disable Low Power Mode.
Note:
Enable Low Power Mode to completely power down when the projector is turned off. Disable Low Power Mode to allow multimedia functionality when the projector is turned off.
Note:
To use the 3D function, the Play Movie in 3D setting found in your player under the 3D Disc
Menu must be enabled. 3D functionality works when the input source supports 120Hz.
1.
The 3D OSD menu item is gray if there is no appropriate 3D source. This is the default setting.
2.
When the projector is connected to an appropriate 3D source, the 3D OSD menu item is enabled for selection.
3.
Use 3D glasses to view a 3D image.
4. You need 3D content from a 3D DVD or 3D media file.
5. You need to enable the 3D source (some 3D DVD content may have a 3D on-off selection feature).
6.
You need DLP link 3D or IR 3D shutter glasses. With IR 3D shutter glasses, you need to install a driver on your PC and connect a USB emitter.
7.
The 3D mode of the OSD needs to match the type of glasses (DLP link or IR 3D).
8. Power on the glasses. Glasses normally have a power on-off switch. Each type of glasses has their own configuration instructions. Please follow the configuration instructions that come with your glasses to finish the setup process.
37
OSD Menu Setting
ITEM
Menu Position
Translucent Menu
Menu Display
Peripheral Test
DESCRIPTION
Press the ◄ or ► button to select different OSD location.
Press the ◄ or ► button to select OSD background translucent level.
Press the ◄ or ► button to select OSD timeout delay.
ITEM
Remote Control Test
Color Test
Button Test
DESCRIPTION
Press to test the IR remote controller for diagnostic.
Press to select different colors on screen.
Press to test the button on keypad.
38
3D
ITEM
3D
3D Sync Invert
DESCRIPTION
Press the ◄ or ► button to select Off, DLP-Link or IR.
Press the ◄ or ► button to turn 3D Sync Invert On or Off.
Factory Reset
To reset all of the menu items to the factory default values (except Language and Security
Lock), perform the following steps:
1. Press the ▲ or ▼ button to move the cursor up or down in the Installation II menu.
2. Select the Factory Reset sub menu.
3. Press .
39
Status
To see the status of the Qumi, perform the following steps:
1. Press the ▲ or ▼ button to move the cursor up or down in the Installation II menu.
2. Select the Installation II sub menu.
3. Press to enter the Status sub menu.
ITEM
Active Source
Video Information
LED Hours
DESCRIPTION
Displays the activated source.
Displays resolution/video information for RGB source and color standard for Video source.
LED use information is displayed (in hours). Eco and Normal counters are separated.
40