2. Product Specifications
SC360 System Controller
SPECIFICATION DESCRIPTION
Model TSYS2C60A2VVU
Product SC360 System Controller
Size 5.55” x 4.54” x 1” (WxHxD)
Configurations Heat Pump, Heat/Cool, Dual Fuel, Heat Only, Cooling Only
Maximum Number of Stages 5 Stages Heat, 2 Stages Cooling
Storage Temperature -40°F to +176°F, 0-95% RH non-condensing
Operating Temperature -10°F to +122°F, 0-60% RH non-condensing
Input Power* 24VAC from HVAC System (Range: 18-30 VAC)
Power Consumption 3W (typical) / 4.7W (max)
Wire Usage 18 AWG NEC approved control wiring
Communications
Controller Area Network (CAN bus) 4-wire connection
Wi-Fi 802.11b/g/n
Bluetooth Low-Energy
System Modes Auto, Heating, Cooling, Off, Emergency Heat
Fan Modes Auto, On, Circulate
Cooling Setpoint Temperature Range 60°F to 99°F, 1°F resolution
Heating Setpoint Temperature Range 55°F to 90°F, 1°F resolution
Outdoor Temperature Display Range
Ambient Temperature: -40°F to 141°F (including dead band),
-38°F to 132°F (excluding dead band)
External Ambient Temperature: up to 136°F
Indoor Humidity Display Range 0% to 100%, 1% resolution
Minimum Cycle Off Time Delay Compressor: 5 minutes, Indoor Heat: 1 minute
* On every application, 24VAC loads should be reviewed to be sure the indoor unit control power transformer is adequately sized.
3. General Information
3.1 What’s in the Box?
• Literature
- Installer Guide
- Warranty Card
• SC360 System Controller
• Wall Plate
• CAN Distribution Board
• CAN Connector Pack
• 2 ft. Harness
• 6 ft. Harness
• Mounting Kit
• Duct Sensor Kit
3.2 Accessories
• Wired Indoor Sensor (ZZSENSAL0400AA)
• Wireless Indoor Sensor (ZSENS930AW00MA*)
* Wireless Indoor Sensor software version 1.70 or greater is required.
3.3 Software Updates
To take full advantage of the features and benefits of the SC360 System Controller, the latest software revision should be installed.
An internet connection is required for software updates. When the SC360 is connected to the
Internet, software updates will occur automatically and do not require user intervention.
18-HD95D1-1C-EN 3
Installation Guide
4. Trane
®
& American Standard
®
Link Systems
• Installation.
Trane and American Standard
Link systems are built to be “plug and play”.
Once you’ve connected the outdoor unit, indoor unit, SC360, and UX360, turn on the system. The equipment will communicate and configure the system automatically to default settings.
• Verification.
You can easily verify all modes of operation. Link can run and verify each mode of operation as well as verify the system is functioning properly. For example, instruct the system to deliver 1200 CFM of airflow, and the system will verify correct operation. Once testing has been completed, you can get a commissioning report that documents the results.
• Monitoring.
With a homeowner’s permission, you can monitor data from the system remotely. This includes creating a birth certificate that captures how the system was operating on day one, and tracking performance over time.
• Upgrades.
Connected systems can have their software remotely upgraded through the SC360, including pushing additional features out to the installed communicating equipment. No dealer visit or SD cards are required.
Technical Advantages
• Self-configuring system on startup
• Automated verification simplifies charging and airflow procedures, and automatically goes through all modes of operation to verify the system is operating properly and within specifications
• New sensors to easily monitor data, with information shared wirelessly, either onsite or in the cloud
• Standardized and consistent wiring: four-wire connection for all communicating equipment simplifies installation
• Faster, more robust communication protocol
• SC360 controls all system decisions, and has Temperature and Humidity sensing capabilities as well as Wi-Fi and BLE communications on-board.
• Remotely control connected systems from the Home mobile app.
• The system supports up to four indoor temperature and humidity sensors in a non-zoned system for averaging, including
ZSENS930AW00MA sensors.
Download the Trane Diagnostics or American Standard Diagnostics mobile app from the
Google Play ™ Store or App Store ® .
