Getting Started. Pentax Optio Optios7, Optio S-7, S7, Optio S7
Werbung
Werbung
Getting Started
Attaching the Strap
Pass the narrow end of the strap through the strap lug and pass the other end through the loop.
1
13
1
Powering the Camera
2
1
1
3
Battery
2
Battery lock lever
Installing the Battery
Install the battery provided with the camera.
1
Open the battery/card cover.
Slide the battery/card cover in the direction indicated by the arrow 1 and flip the cover open 2 .
2
Insert the battery with the 2 symbol facing toward the LCD monitor while using the side of the battery to press the battery lock lever in the direction indicated by the arrow.
3
Close the battery/card cover.
Removing the Battery
1
Open the battery/card cover.
2
Release the battery by using your finger to press the battery lock lever in the same direction as when you inserted the battery.
Pull the battery out.
14
If you intend to use the camera continuously for a long period, use of the AC adapter kit K-AC8 (optional) is recommended. (
• Insert the battery correctly. If the battery is incorrectly oriented, it may cause a malfunction.
• Do not remove the battery when the camera is turned on.
• If you do not intend to use the camera for a long time, remove the battery.
• If the camera is left without the battery for a long time, the date will be reset.
1
15
1
Charging indicator Battery
3
To power outlet
2
Battery charger
1
AC plug cord
Charging the Battery
Use the battery charger D-BC8 supplied with the camera to charge the battery before using the camera for the first time or when the [Battery depleted] message appears.
1
Connect the AC plug cord to the battery charger.
2
Plug the AC plug cord into the power outlet.
3
Place the battery in the battery charger so that the
PENTAX name is visible.
The charging indicator on the charger lights red while the battery is being charged and changes to green when charging is completed.
4
Remove the battery from the battery charger when charging is completed.
16
• The time required for full charge is about 100 minutes.
The appropriate ambient temperature range for charging the battery is 0°C – 40°C (32°F to 104°F).
• The charging time may vary depending on the ambient temperature and charging conditions.
• When the battery reaches the end of its service life, the time that the camera can be operated becomes shorter even when the battery is fully charged. In this event, replace the battery.
• Always charge the battery before using the camera for the first time or when the battery has not been used for a long time.
• Do not use the battery charger D-BC8 to charge batteries other than D-LI8 rechargeable lithium-ion batteries, as the charger may overheat or be damaged as a result.
• If the battery is inserted correctly but the charging indicator blinks, the battery may be faulty. Replace with a new battery.
1
17
1
• Approximate Operating Time (when the D-LI8 battery is fully charged)
Number of recordable images: Approx. 180 (at 23°C with the LCD monitor on and the flash used for 50% of shots)
Playback time:
Movie recording time:
Sound recording time:
Approx. 130 min.
Approx. 60 min.
Approx. 140 min.
• The number of recordable images are based on CIPA standard measurement and may vary depending on capture mode and shooting conditions.
• In general, battery performance temporarily deteriorates as the temperature decreases. When using the camera in a cold environment, keep it warm by putting it in your pocket or inside your coat. Battery performance that has deteriorated due to low temperature will be restored when the battery is returned to room temperature.
• Be sure to take a spare battery with you when traveling abroad or to a cold region, or if you intend to take a lot of pictures.
• Battery Level Indicator
You can check the battery level by the symbol on the LCD monitor.
(lit green) : Adequate power remains.
↓
(lit green) : Battery is running low.
↓
(lit yellow) : Battery is running very low.
↓
(lit red)
↓
[Battery depleted]
: Battery is exhausted.
: The camera will turn off after the message appears.
• Recycling Batteries
This symbol indicates that the battery is recyclable.
Cover the terminals with insulating tape and take the battery to a store displaying this symbol.
18
Charging the Battery Abroad
The battery charger supplied with the camera is designed to switch automatically to the voltage (100-240V) and frequency (50Hz, 60Hz) of the electricity supply in the country or region where used.
However, electrical socket shapes differ depending on the country or region. Before traveling abroad, you are advised to check the socket
shape in your destination (see “Main Socket Types in the Major
Countries and Regions of the World” (p.20)) and take an appropriately
shaped off-the-shelf adapter plug with you. (Electrical socket shapes may vary depending on every region in the country. Check the socket shape used in the region.)
The socket shape does not affect the charging method.
Adapter plug
1
Type
• Use of an off-the-shelf transformer may lead to defective operation.
• Unplug the adapter plug from the power outlet when the battery charger is not in use.
A B BF C S
—
19
Main Socket Types in the Major Countries and Regions of the
World
1
North America U.S.A., Canada
Europe,
Former Soviet
Union
Iceland, Ireland, Italy, Ukraine, Austria,
Netherlands, Kazakhstan, Greece, Sweden,
Denmark, Germany, Norway, Hungary, Finland,
France, Belarus, Belgium, Rumania, Russia
Asia
U.K.
Spain
Switzerland, Poland, Portugal
Taiwan, Japan
Sri Lanka, Maldives
Nepal, Bangladesh, Mongolia
Vietnam
India, Indonesia, Pakistan, Macau
Oceania
Thailand
Korea
Philippines
Singapore, Hong Kong
China
Malaysia
Australia, Tonga, New Zealand, Fiji
Guam
Tahiti
Central and
South
America
Colombia, Jamaica, Haiti, Panama, Bahamas,
Puerto Rico, Venezuela, Mexico
Brazil, Peru
Chile
Argentina
Middle East Israel, Iran
Kuwait
Africa
Jordan
Canary Islands, Guinea, Mozambique, Morocco
Kenya, South Africa
Algeria
Egypt
Zambia, Tanzania
A
9
9
9
9
9
9
9 9
9
9
9 9
9
9
9
9
B
9
9
9
9
9
9
9
9 9
9
9
BF
9
9
9
9 9
9
9
C
9
9
9
9
9
9
9
9
9
9
9
9
9
9 9
9
9
9
9 9
9
9
9
S
9
9
9
9
20
4 symbols
AC adapter
2
1 4
To power outlet
AC plug cord
3
Using the AC Adapter (optional)
If you intend to use the LCD monitor for a long time or connect the camera to a PC, use of the AC adapter kit K-AC8 (optional) is recommended.
1
Make sure that the camera is turned off and open the battery/card cover.
2
Connect the DC terminal on the AC adapter to the DC input terminal on the camera, being sure to match the
4 symbols.
3
Connect the AC plug cord to the AC adapter.
4
Plug the AC plug cord into the power outlet.
• Make sure that the camera is turned off when connecting or disconnecting the AC adapter.
• Make sure that the AC plug cord and connecting cable are inserted securely. The data may be lost if the cable becomes disconnected while you are taking pictures.
• Be sure to read the operating manual accompanying the AC adapter before using the adapter.
• Be sure to match the 4 symbols when connecting the DC terminals.
Inserting the plugs with too much force may damage them.
1
21
1
Precautions When Using the Battery Charger or AC Adapter
To avoid the risk of fire or electric shock when using the battery charger
or AC adapter, be sure to read the section on “USING YOUR CAMERA
SAFELY” on page 1. Refer to page 181 for the specifications of the
battery charger and AC adapter.
22
Installing the SD Memory Card
1 2
SD Memory Card
2
1
3
To remove the card, push in and pull out
1
An SD Memory Card can be used with this camera. Captured images are recorded on the SD Memory Card if a card is inserted or in the built-in memory if no card is inserted.
• Make sure that the camera is turned off before inserting or removing the SD Memory Card.
• Be sure to format unused cards or cards that have been used on
another camera. Refer to “Formatting an SD Memory Card or the
Built-in Memory” (p.152) for instructions on formatting.
1
Open the battery/card cover.
Slide the battery/card cover in the direction indicated by the arrow 1 and flip the cover open 2 .
2
Insert an SD Memory Card so the label (the side with the
2 symbol) is facing toward the LCD monitor and push the card in until it clicks.
3
Close the battery/card cover.
To remove the card, eject the card by pressing it in the direction indicated by the arrow and pull it out.
The number of recordable images varies depending on the capacity of the SD Memory Card or built-in memory and the selected image size and quality. ( 1
23
1
24
Data Backup
Very occasionally, data stored in the built-in memory becomes unreadable. As a backup measure, we recommend that you download important data to a PC or store the data in a medium other than the built-in memory.
Precautions When Using an SD Memory Card
• Make sure that the camera is turned off before opening the battery/card cover.
• The SD Memory Card is equipped with a write-protect switch.
Write-protect switch
Setting the switch to [LOCK] protects the existing data by prohibiting recording of new data, deletion of existing data or formatting of the card.
• Care should be taken if you remove the SD Memory Card immediately after using the camera, as the card may be hot.
• Do not remove the SD Memory Card or turn the camera off while data is being recorded on the card, images or sound are being played back, or the camera is connected to a PC with the USB cable as this may cause the data to be lost or the card to be damaged.
• Do not bend the SD Memory Card or subject it to violent impact. Keep it away from water and store away from high temperature.
• Be sure to format unused cards or cards that have been used on another camera.
Refer to “Formatting an SD Memory Card or the Built-in Memory” (p.152) for
instructions on formatting.
• Do not remove the SD Memory Card during formatting as this may damage the card and render it unusable.
• The data on the SD Memory Card may be deleted in the following circumstances.
PENTAX does not accept any liability for data that is deleted
(1) when the SD Memory Card is mishandled by the user.
(2) when the SD Memory Card is exposed to static electricity or electrical interference.
(3) when the card has not been used for a long time.
(4) when the card is ejected, the AC adapter is disconnected or the battery is removed while the data on the card is being recorded or accessed.
• The SD Memory Card has a limited service life. If it is not used for a long time, the data on the card may become unreadable. Be sure to regularly make a backup of important data on a PC.
• Avoid using or storing the card where it may be exposed to static electricity or electrical interference.
• Avoid using or storing the card in direct sunlight or where it may be exposed to rapid changes in temperature or to condensation.
• When using an SD Memory Card with a slow recording speed, recording may stop while you are taking movies even when there is adequate space in the memory, or shooting and playback may take a long time.
• When you purchase the SD Memory Card, access the PENTAX website and confirm beforehand if they have compatibility with your camera. Inquiries on the card compatibility can also be answered by your nearest PENTAX service center.
• If you are going to discard, give away or sell your SD Memory Card, you should ensure that the data on the card is completely deleted or the card itself is destroyed if it contains any personal or sensitive information. Please note that formatting the
SD Memory Card will not necessarily delete the data so that it cannot be recovered using off-the-shelf data recovery software. There are off-the-shelf secure data deletion software programs available that will completely delete the data. In any case, the data on your SD Memory Card should be managed at your own risk.
Image Size and Quality of Still Pictures
Choose the image size and quality best suited to your purpose.
Higher quality levels and numbers of recorded pixels produce clearer images for printing, but the resulting increase in data volume reduces the total number of pictures that can be taken.
When you choose high image quality as well as a large image size, it may take ten seconds or more for the camera to finish recording after shooting.
Choose the appropriate number of recorded pixels and quality level on the [ A Rec. Mode] menu.
How to Set the Menus 1
Selecting the Recorded Pixels of Still Pictures 1
Selecting the Quality Level of Still Pictures 1
Appropriate Sizes According to Use
7M (3072×2304)
5M (2592×1944)
4M (2304×1728)
3M (2048×1536)
2M (1600×1200)
1024 (1024×768) 0
Printing images with high-resolution settings in your printer,
Printing at A4 size or larger, Editing and processing images
640 (640×480)
Printing at postcard size
For use as images on websites, For attaching images to e-mail
The default setting is 7M (3072×2304).
Appropriate Quality According to Use
C Best
D Better
E Good
Lowest compression ratio. Suitable for large A4-size photo prints.
Standard compression ratio. Suitable for photo prints or viewing images on a computer screen.
Highest compression ratio. Suitable for attaching to e-mails or creating websites.
The default setting is D .
1
25
1
Approximate Number of Recordable Images by Size and Quality
Quality Level
Recorded Pixels
7M (3072×2304)
5M (2592×1944)
4M (2304×1728)
3M (2048×1536)
Best
C
104
147
187
223
Better
D
151
213
270
323
Good
E
210
296
375
448
Sound
313
571
1048
453
826
1515
628
1144
2098
4 hr.
19 min. 59 sec.
2M (1600×1200)
1024 (1024×768) 0
640 (640×480)
• The above table indicates the approximate number of images and recording time when using a 256 MB SD Memory Card.
• The above table is based on standard shooting conditions specified by
PENTAX and may vary depending on the subject, shooting conditions, capture mode, SD Memory Card, etc.
Size and Quality of Movies
Choose the size and quality best suited to your purpose.
The larger size and the higher quality level E are chosen, the clearer moving images are produced, but the file size is increased.
Choose the appropriate size and quality on the [ A Rec. Mode] menu.
Selecting the Recorded Pixels of Movies 1
Selecting the Quality Level of Movies 1
Appropriate Sizes (Recorded Pixels) According to Use
640 (640×480)
Viewing high-quality movies at VGA size. The recordable time is shorter.
320 (320×240) Smaller data volume allows a longer time recording.
The default setting is 640 (640×480).
26
Approximate Recordable Time by Size (Recorded Pixels) and
Quality
Quality Level
Recorded Pixels
640 (640×480)
320 (320×240)
C
S.Fine
11 min. 35 sec.
44 min. 47 sec.
D
Fine
14 min. 30 sec.
55 min. 39 sec.
E
Economy
17 min. 25 sec.
64 min. 10 sec.
The default setting is C .
• The above table indicates the approximate recording times when using a 256
MB SD Memory Card.
• The above table is based on standard shooting conditions specified by
PENTAX and may vary depending on the subject, shooting conditions, capture mode, SD Memory Card, etc.
1
27
1
Initial Settings (Setting the Display
Language and the Date and Time)
Power switch
Four-way controller
OK button
If the Initial Setting screen or Date Adjust screen appears when you turn the camera on, follow the procedure below to set the display language and/or current date and time.
If the Initial Setting screen appears:
1
p.28 - 29 “Setting the Display Language”, “Setting the
If the Date Adjust screen appears:
1
p.29 - 30 “Setting the Date and Time”
If you want to change the initial settings, refer to “Changing the Date
and Time” (p.156) and “Changing the Display Language” (p.160).
28
Setting the Display Language
You can choose the language in which the menus, error messages, etc. are displayed from the following: English, French, German, Spanish,
Portuguese, Italian, Swedish, Dutch, Russian, Thai, Korean, Chinese
(traditional and simplified) and Japanese.
1
Press the four-way controller ( 5 ).
Initial Setting
The Language/ screen appears.
2
Use the four-way controller
( 2345 ) to choose a language.
Hometown
New York
English
0:00
The default setting is English.
3
Press the OK button.
Video Out
MENU Cancel
NTSC
OK OK
4
Press the four-way controller ( 3 ).
The frame moves to [ W ].
5
Use the four-way controller ( 45 ) to choose the desired city (Hometown).
6
Press the four-way controller ( 3 ).
The frame moves to [DST] (Daylight Saving Time).
7
Use the four-way controller ( 45 ) to select O (On) or
P (Off).
8
Press the OK button.
The Date Adjust screen appears.
Setting the Date and Time
Set the current date and time and the display style.
1
Press the four-way controller ( 5 ).
Date Adjust
The frame moves to [mm/dd/yy].
2
Use the four-way controller ( 23 ) to choose the date display style.
Date Style
Date
Time mm/dd/yy 24h
0 1 / 0 1 / 2 0 0 6
0 : 0 0
MENU Cancel OK OK
3
Press the four-way controller ( 5 ).
The frame moves to [24h].
4
Use the four-way controller ( 23 ) to select [24h] (24-hour display) or
[12h] (12-hour display).
5
Press the four-way controller ( 5 ).
The frame returns to [Date Style].
6
Press the four-way controller ( 3 ).
The frame moves to [Date].
Date Adjust
Date Style mm/dd/yy 24h
Date
Time
MENU Cancel
0 1 / 0 1 / 2 0 0 6
0 : 0 0
OK OK
Date Adjust
Date Style mm/dd/yy 24h
Date
Time
MENU Cancel
0 1 / 0 1 / 2 0 0 6
0 : 0 0
OK OK
1
29
1
7
Press the four-way controller ( 5 ).
Date Adjust
The frame moves to the month.
8
Use the four-way controller ( 23 ) to change the month.
Date Style
Date mm/dd/yy 24h
0 1 / 0 1 / 2 0 0 6
Change the day and year in the same manner.
Time
MENU Cancel
0 : 0 0
OK OK
Next, change the time.
If you selected [12h] in Step 4, the setting switches between am and pm corresponding to the time.
• When you finish the settings and press the OK button, the camera clock is reset to 00 seconds.
• To set the exact time, press the OK button when the time signal
(on the TV, radio, etc.) reaches 00 seconds.
30
• When the Initial Settings screen is displayed, you can cancel the setting operation and switch to Capture mode by pressing the
MENU button. In this case, the Initial Settings or Date Adjust screen will appear next time you turn the camera on.
• You can change the settings on the menu. Refer to the pages below for details.
Language: “Changing the Display Language” (p.160)
City, Daylight saving time: “Setting the World Time” (p.158)
Date and Time: “Changing the Date and Time” (p.156)
• The video output format is automatically set in conjunction with the language you have chosen as listed below. If the output format is different from the one used in your country or region, change the
format following the steps in “Changing the Video Output Format”
Language
English (English)
French ( )
German (Deutsch)
Spanish (
Portuguese (
)
)
Italian (Italiano)
Sweden (Svenska)
Netherlands (Nederlands)
Russian ( )
Thai( )
Korean ( )
Chinese (traditional) (
Chinese (simplified) (
Japanese
)
)
PAL
PAL
PAL
NTSC
PAL
PAL
NTSC
Video Output Format
NTSC
PAL
PAL
PAL
PAL
PAL
PAL
1
31
Herunterladen
Öffentlicher Link aktualisiert
Der öffentliche Link zu Ihrem Chat wurde aktualisiert. Sie können Ihre Chat-Links nach der Registrierung hier einsehen und verwalten.
Öffentlicher Dokumentenlink
Werbung