advertisement
TG2388.book 32 ページ ２００５年７月１４日 木曜日 午後４時５８分
Locator/Intercom
Locator/Intercom
Intercom calls can be made between the handset and the base unit.
Making intercom calls
Using the handset
1
Press
{
HOLD/INTERCOM
}
.
Calling Base
L
The base unit will ring for 1 minute.
L
To stop paging, press
{
OFF
}
.
2
When the paged party answers, start talking.
Intercom
00-00-05
L
You can switch to the speaker by pressing
{s}
. To switch back to the receiver, press
{C}
.
3
To disconnect the intercom, press
{
OFF
}
.
Using the base unit
1
Press
{
LOCATOR/INTERCOM
}
.
L
The SP-PHONE indicator lights.
L
The handset will ring for 5 minutes.
L
To stop paging, press
{
SP-PHONE
} or
{
LOCATOR/INTERCOM
}
.
2
When the paged party answers, talk into the
MIC
.
3
To disconnect the intercom, press
{
SP-
PHONE
}
or
{
LOCATOR/INTERCOM
}
.
L
The indicator light goes out.
During an intercom call:
L
If you have difficulty hearing while using the handset speakerphone and base unit speaker, decrease the speaker volume by pressing
VOLUME
{
<
}
on the base unit or
{V} on the handset.
L
If an incoming call is being received, you will hear two tones (incoming call tone, page 40) and “
BC
” will flash rapidly on the base unit.
To answer the call;
— if using the handset, press
{
OFF
}
, then
{C}
or
{s}
.
— if using the base unit, press
{
SP-
PHONE
}
twice
.
Answering intercom calls
Using the handset
When a handset is paged, it rings and the
Ringer/Message Alert indicator flashes rapidly.
1
Press
{C}
,
{s}
or
{
HOLD/
INTERCOM
}
.
Call from Base
L
You can also answer a call by pressing any button except
{V}
,
{^} or
{
OFF
}
.
2
To disconnect the intercom, press
{
OFF
}
.
Using the base unit
When the base unit is being paged, it rings.
1
Press
{
SP-PHONE
}
or
{
LOCATOR/
INTERCOM
}
.
2
To disconnect the intercom, press
{
SP-
PHONE
}
or
{
LOCATOR/INTERCOM
}
.
32
For assistance, please visit http://www.panasonic.com/consumersupport
TG2388.book 33 ページ ２００５年７月１４日 木曜日 午後４時５８分
Locator/Intercom
L
When the ringer volume is turned off
(page 39), the handset and the base unit will ring at the low level for intercom calls.
L
You cannot change the ringer tone for intercom calls.
Transferring a call
You can transfer an outside call to the base unit or the handset.
L
The call is put on hold.
L
If the paged party does not answer, press
{
LOCATOR/INTERCOM
}
to return to the outside call.
2
Handset:
Press
{C}
,
{s}
or
{
HOLD/
INTERCOM
}
to answer the page.
L
You can also answer a call by pressing any button except
{V}
,
{^} or
{
OFF
}
.
3
Base unit:
To complete the transfer, press
{
SP-
PHONE
}
.
From the handset to the base unit
1
Handset:
(1)During a call, press
{
HOLD/
INTERCOM
}
.
Quick call transfer
You can transfer a call without waiting for the paged party to answer.
Line on hold.
Transfer to
Base
Using the handset
L
The call is put on hold.
(2)Press
{
Base
}
.
1
During a call, press
{
HOLD/
INTERCOM
}
, then press
{
Base
}
.
2
Press
{
OFF
}
to hang up.
Hold
Calling Base
Using the base unit
1
(3)Wait for the paged party to answer, then you can announce the transfer.
L
After the paged party answers,
“
Intercom hold
” is displayed.
L
If the paged party does not answer, press
{C}
or
{s}
to return to the outside call.
2
Base unit:
Press
{
SP-PHONE
}
or
{
LOCATOR/
INTERCOM
}
to answer the page.
3
Handset:
To complete the transfer, press
{
OFF
}
.
From the base unit to the handset
Base unit:
During a call, press
{
LOCATOR/
INTERCOM
}
.
1
2
During a call, press
INTERCOM
}
.
Press
{
SP-PHONE
}
{
LOCATOR/
to hang up.
L
The call will be transferred directly.
L
For the paged party to answer the transferred call:
– for the handset, press
{C}
or
{s}
.
– for the base unit, press
{
SP-PHONE
}
.
L
After the paged party answers, the transfer is complete.
L
If the paged party does not answer:
– for the handset, press
{C}
or
{s}
.
– for the base unit, press
{
SP-PHONE
}
.
L
If the paged party does not answer within 60 seconds after you hang up, your phone will ring and the call will be returned to your phone.
To speak to the caller again:
For assistance, please visit http://www.panasonic.com/consumersupport
33
TG2388.book 34 ページ ２００５年７月１４日 木曜日 午後４時５８分
Locator/Intercom
– for the handset, press
{C}
or
{s}
to return to the outside call.
– for the base unit, press
{
SP-PHONE
} to return to the outside call.
conference by pressing
{
Conf
}
on the handset or
{
HOLD/CONF
}
on the base unit.
Conference calls
While you are talking with an outside caller, the base unit user or the handset user can join the conversation and establish a conference call.
Call share
This feature allows the base unit or the handset to join an existing outside call.
To join a conversation (Call Share)
Using the handset
Press
{C}
or
{s}
.
L
“
Conference
” is displayed.
Using the base unit
Press
{
SP-PHONE
}
.
Using the handset
1
During a call, press
{
HOLD/
INTERCOM
}
.
L
The call is put on hold.
2
Press
{
Base
}
.
3
When the paged party answers, press
{
Conf
}
on your unit to make a conference call.
L
“
Conference
” is displayed during a conference call.
Using the base unit
1
During a call, press
{
LOCATOR/
INTERCOM
}
.
L
The call is put on hold.
2
When the paged party answers, press
{
HOLD/CONF
}
on your unit to make a conference call.
Note:
L
To leave the conference, press
{
OFF
} on the handset or press
{
SP-PHONE
} on the base unit. The two other parties can continue the conversation.
L
During a conference, the outside call can be placed on hold by pressing
{
HOLD/INTERCOM
}
on the handset or
{
HOLD/CONF
}
on the base unit.
Internal communications are not suspended. Only the person who placed the call on hold can resume the full
34
For assistance, please visit http://www.panasonic.com/consumersupport
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project