INSTALLATION REQUIREMENTS. Maytag W10135283A, MAT14CSAWW0, 120-volt

IMPORTANT SAFETY INSTRUCTIONS

WARNING:

To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic precautions, including the following:

■

Read all instructions before using the washer.

■

Do not wash articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, other flammable, or explosive substances as they give off vapors that could ignite or explode.

■

Do not allow children to play on or in the washer. Close supervision of children is necessary when the washer is used near children.

■

Before the washer is removed from service or discarded, remove the door or lid.

■

Do not add gasoline, dry-cleaning solvents, or other flammable, or explosive substances to the wash water.

These substances give off vapors that could ignite or explode.

■

Do not reach into the washer if the drum, tub or agitator is moving.

■

Do not install or store the washer where it will be exposed to the weather.

■

Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for 2 weeks or more. HYDROGEN GAS IS

EXPLOSIVE. If the hot water system has not been used for such a period, before using the washing machine, turn on all hot water faucets and let the water flow from each for several minutes. This will release any accumulated hydrogen gas. As the gas is

■

Do not tamper with controls.

■

Do not repair or replace any part of the washer or attempt any servicing unless specifically recommended in this manual or in published user-repair instructions that you understand and have the skills to carry out.

■

See “Electrical Requirements” for grounding instructions.

flammable, do not smoke or use an open flame during this time.

SAVE THESE INSTRUCTIONS

■

■

■

■

■

■

■

Level

Utility knife

Scissors

8" or 10" adjustable wrench

Flat-blade screwdriver

Pliers

Bucket

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation.

Tools needed

Parts supplied

Remove parts bag from washer. Check that all parts were included.

■

■

1 hose clamp

2 inlet hoses

■

■

■

4 flat water hose washers

2 front-leveling legs with nuts

1 drain hose

Location Requirements

IMPORTANT: Do not install or store the washer where it will be exposed to the weather. Do not store or operate the washer in temperatures at or below 32°F (0°C). Some water can remain in the washer and can cause damage in low temperatures.

Proper installation is your responsibility.

You will need:

■

■

A water heater set to deliver 120°F (49°C) water to the washer.

A grounded electrical outlet located within 4 ft (1.2 m) of where the power cord is attached to the back of the washer.

See “Electrical Requirements.”

■

■

■

Hot and cold water faucets located within 4 ft (1.2 m) of the back of the washer, and provide water pressure of 10-100 psi

(69-690 kPa). A pressure reduction valve should be used in the supply line where inlet pressure entering the building exceeds 100 psi (690 kPa) to prevent damage to the washer mixing valve.

A level floor with a maximum slope of 1" (2.5 cm) under entire washer.

A sturdy floor to support the washer weight (washer, water and load) of 315 lbs (143 kgs).

■

■

A 12" (30 cm) minimum riser to provide an air cushion and prevent noise and damage to valves for a single washer installation.

A floor drain should be provided under the bulkhead.

Prefabricated bulkheads with electrical outlets, water supply lines and drain facilities should be used only where local codes permit.

NOTE: Front access to the pump area is available by removing

2 clips under the console area and removing the top and cabinet assembly.

3