advertisement
Cloning Learning Setup
Learning the Master TV Setup
Instructions for the Clone Programmer to Learn the Master TV Setup
Use MPI Cable to Connect LT2002 Clone Programmer to
Master TV MPI Port
If there is a good connection, “THE CLONE HAS CONTROL OF TV” message will appear. Press any key on the Installer remote.
Learn Setup from Master TV
Press 1 to select the “LEARN FROM TV” option, then press ON/OFF,
POWER, or ENTER to go to the Memory Bank Selection Menu. Pick the
Memory ”Bank” you want to store the master TV’s setup in by pressing either Channel key repeatedly to choose Memory 1, 2 or 3. (If you choose a Memory “Bank” that has a master device’s setup programmed into it, that setup will be overwritten by the new master
TV’s setup.) Once the Clone memory bank is selected, press ON/OFF,
POWER, or ENTER. The Clone memory bank you have selected will be shown. Press ON/OFF or POWER to begin copying the master TV’s setup.
Set the Clock (Optional)
Set the time on a Master TV’s Clock. (If the time has already been copied from a TV into the Clone programmer, you can set a master
TV’s clock by copying the time from the Clone programmer.) The
Clone Programmer can copy the current time to both a master TV and to the Clone’s internal clock; accurate to within one minute. (Another reason that the Clone programmer should be equipped with fresh, high-quality alkaline batteries, is for it to keep the time as accurately as possible.)
Since the Clone Programmer’s time cannot be set directly, the current time needs to be copied from a Zenith/LG TV equipped with M.P.I.
input capability.
After the time is copied to the Clone programmer, the current time can then be transferred to another TV. (This can be a master TV, or another TV which has already had the features set up.)
THE CLONE HAS CONTROL OF THE TV
THE CLONE IS VERSION
THE TV IS VERSION
THE SW IS REVISION
XX
XX
XX
CLONE CLOCK=
TV CLOCK=
XX:XX
XX:XX
-PRESS ANY KEY TO CONTINUE.
-DISCONNECT CLONE WHEN DONE.
This menu should appear by itself after the
LT2002 is connected to the TV MPI port.
CLONE SELECTION MENU
(1) LEARN FROM TV
(2) TEACH TO TV
(3) SET CLONE CLOCK FROM TV
(4) SET TV CLOCK FROM CLONE
(5) DISPLAY TV SETUP
(6) DISPLAY CLONE SETUP
-TO CHANGE MENU ITEMS, PRESS
CHANNEL KEYS OR DIGITS.
-TO EXECUTE ITEM, PRESS ON/OFF,
POWER, OR ENTER
This menu should appear after any key is pressed on the Installer remote.
LT2002 Clone Programmer Communication Problems
• A slow flashing green light indicates there are communication problems between the TV and the LT2002 clone programmer. If this is the case, check for a damaged cable, poor contacts, or other connection troubles.
• If the status indicator is red, the programmer batteries are low and should be replaced. Install 4 high-quality alkaline
AA batteries.
P A G E 8
206-4071
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 2 Installer Overview
- 3 Table of Contents
- 4 Typical Installer’s Remote Control
- 6 Commercial Mode Setup
- 7 Master TV Cloning Connections and Cloning Overview
- 8 Cloning Learning Setup
- 9 Cloning Connections/ Teaching Setup
- 15 Installer’s Menus
- 16 Clonable Menu Features Chart
- 18 Detailed Instructions For Making A Master TV
- 19 Software Updating Procedure
- 20 Camport Auto Sense Operation
- 21 Aux Input Configuration
- 22 Troubleshooting
- 23 Cloning Troubleshooting
- 24 Troubleshooting Flow Chart
- 25 Commercial Mode Check
- 26 RJP Mode Configuration
- 27 Glossary of Terms
- 28 Back Cover