Introducción. Philips SRU3003-27, SRU2103/27, SRU3003, SRU 3003, SRU3003/27, PM335

Setup, cont.

Controlling Devices Requiring Separate Power On and

Off Buttons, cont.

To turn the TV off, press and release the

POWER

button to transmit the Power Off button command. This method can be applied similarly to any device and is available for all Modes. Note this feature is not supported by all codes.

VCR/DVD/DVR Punch-Through Feature

This remote allows the 6 VCR transport buttons (i.e.

PLAY

,

PAUSE

,

STOP

,

FF

,

REWIND

, and

REC

) to

Punch-Through control from any Mode programmed with TV, SAT or Cable codes to the last

VCR

,

DVD

or

DVR

programmed Mode you used. Normally other types of remotes only punch-through (from another

Mode) on the 6 VCR buttons to the device programmed under the

VCR

Mode button. This is not much use if you are using a DVD programmed under a Mode other than VCR. For example, if you have 2 DVD, VCR or DVR devices programmed into this remote, the last one you accessed on the remote will be the one that has control of the 6 VCR transport buttons when in any other

Mode. This feature will not operate if the programmed

TV, SAT or Cable code has its own VCR transport button control e.g. a TV Combo, SAT/PVR, etc.

Volume/Mute Control and Punch-Through Feature

This remote lets you select which device Mode controls your Volume/Mute buttons. The remote is initially set

(factory default) for all device Modes programmed with

“

Visual

” codes (e.g. TV, VCR, DVD, DVR, SAT &

CABLE) and “

Audio

” codes (e.g. CD & AUDIO) to use their own Volume/Mute control if present. If the programmed “

Visual

” code has no Volume/Mute operation of its own then those buttons will punchthrough control to the

TV

Mode device without needing to change to

TV

Mode. Please refer to the next page for more information.

Setup, cont.

Any Mode chosen for Volume/Mute control MUST have its own Volume/Mute function or the Volume/Mute buttons will do nothing.

Setting ALL Volume/Mute Control to any one Mode

This routine can set all Modes to “punch-through” to any one chosen Mode for Volume/Mute button control without the needing to change to that Mode.

1. Press and hold the

SETUP

button until the red indicator turns on, then release the button.

2. Press and hold the

MUTE

button until the red indicator blinks off, then release the button.

3. Press and release the desired Mode button (

TV

,

VCR

, etc.) for Volume/Mute control, the red indicator blinks then stays on.

4. Press and release the

MUTE

button and the red indicator turns off. The red indicator will blink rapidly for three seconds if the Mode you have selected has no Volume/Mute control.

5. All other Modes will now punch-through to your chosen Mode for Volume/Mute control.

6. All “Visual” and “Audio” programmed Modes will now punch-through to the respective Modes you have chosen for Volume/Mute control.

Setting any Mode to use its own Volume/Mute Control

This routine can set any Mode to use only its own

Volume/Mute control. Note - If your chosen Mode has no Volume/Mute functions of its own then the Volume/

Mute buttons will do nothing.

1. Press and hold the

SETUP

button until the red indicator turns on, then release the button.

2. Press and hold the

MUTE

button until the red indicator blinks off, then release the button.

3. Press and release the desired Mode button (

TV

,

VCR

, etc.), the red indicator blinks then stays on.

4. Press and release the

VOLUME-

(Down) button, the red indicator blinks then stays on.

5. Press and release the

MUTE

button and the red indicator turns off.

6. All “Visual” and “Audio” programmed Modes will now punch-through to the respective Modes you have chosen for Volume/Mute control.

12 13