Control Names and Locations. Zenith VRE4222, BEJ9QKE40210, VRE4122

CONTROL NAMES AND LOCATIONS

FRONT

POWER

To turn the VCR on and off.

While plugged into an AC outlet, the VCR consumes

2W of electrical power in

OFF condition.

CASSETTE COMPARTMENT

Where the video cassette is inserted.

PAUSE

To put playback on still (page 24) or to pause recording (page 26).

REC/ITR

To record normally (page 26) or to activate Instant Timer Recording

(page 30).

STOP/EJECT

To stop the tape.

To eject the tape in the VCR.

INFRARED REMOTE SENSOR

Receives the signal from the infrared remote control.

power stop/eject rec / itr pause rew play ff ch

CHANNEL (

D

/

E

)

To scan up or down through memorized channels (page 17) or to adjust manually the tape’s picture onscreen (page 22).

VCR Function Indicator Panel

Details are on the next page.

REW (Rewind)

To rewind the tape during the STOP mode or for fast reverse picture search (page 24).

VIDEO IN/AUDIO IN (L/R) JACKS (LINE2)

Connect the audio/video output cable from an external unit (Audio system, TV/Monitor,

Another VCR) to this terminal.

NOTE

To select an A/V input channel (LINE1 or 2), select the next highest or lowest channel programmed in the VCR with the CH/TRK

(

D

/

E

).

PLAY

To play back a recorded tape

(page 22).

FF (Fast Forward)

To advance the tape during the STOP mode or for fast forward picture search (page 24).

9

CONTROL NAMES AND LOCATIONS (Cont’d)

INDICATOR PANEL

Cassette indicator

Lights while a cassette is inserted, and flashes while ejecting a cassette.

Record indicator

VCR indicator

Use TV/VCR on the remote control to turn this indicator ON or OFF.

ON: for playback, VCR programming or watching TV programs through the

VCR tuner

OFF: for watching TV programs through TV tuner

REC

VCR

TIMER

AM

Clock/Tape operation indicator

HI — VCR is turned on.

BYE — VCR is turned off.

TIMER indicator

AM indicator

(PM is not displayed)

Front Panel Display shows which VCR function you are using. For example, when you press SP/SLP, SP or SLP appears to indicate the tape speed. As you change channels, the channel numbers appear. The current time shows even while the VCR is off.

Record Message

Err — Turn VCR On and OFF to erase “Err” message. If it is not erased, take VCR to an authorized repair center.

RECP — Record mode is halted.

SP or SLP — Displays the recording speed.

REC — VCR is recording.

STOP — Recording is stopped.

Playback Messages

Err — Turn VCR On and OFF to erase “Err” message. If it is not erased, take VCR to an authorized repair center.

FF (Fast Forward) — Tape is advancing rapidly.

CUE — Tape is advancing rapidly in playback mode for visual search.

REV — Tape is reversing rapidly in playback mode for visual search.

PLAY — Tape is playing at normal playback speed.

REW (Rewind) — Tape is rewinding rapidly.

SLW — Tape is playing at slow-motion speed.

STILL — Playback is halted on one frame.

STOP — Tape rewind or playback is stopped.

Tuner Messages

L1 or L2 — Auxiliary channel is selected for viewing equipment connected to Audio/Video jacks on front or rear of the VCR.

ch _ — VCR is tuned to Channel _.

HI — VCR is turned on.

BYE — VCR is turned off.

10

CONTROL NAMES AND LOCATIONS (Cont’d)

REAR

ANTENNA INPUT CONNECTOR

Connect the VHF/UHF/CATV antenna to this terminal.

AUDIO OUT (L/R) JACKS; Connect this terminal to the audio input terminal on an external unit (Audio System, TV/Monitor, Another VCR).

VIDEO OUT JACK; Connect this terminal to the video input terminal on an external unit

(TV/Monitor, Another VCR).

AUDIO IN (L/R) JACKS; Connect the audio output cable from an external unit (Audio system, TV/Monitor, Another VCR) to this terminal.

VIDEO IN JACK; Connect the video output cable from an external unit (TV/Monitor,

Another VCR) to this terminal.

NOTE

To select an A/V input channel (LINE1 or 2), select the next highest or lowest channel programmed in the VCR with the CH/TRK (

D

/

E

).

AUDIO

R

ANT.IN

IN OUT

IN

OUT

VIDEO

L

3 4

CH.

VHF/UHF

/CATV

WARNING : Do not drop the tying band of the power cord into the unit. Doing so might cause a fire or an electrical shock.

VCR OUTPUT CHANNEL SELECT SWITCH

POWER CORD

Connect only to an AC 120V, 60Hz outlet.

Set this switch to channel 3 or 4.

VHF/UHF/CATV ANTENNA OUTPUT CONNECTOR

Connect this terminal to the VHF or UHF antenna terminals on the back of a TV.

SET POSITION OF THE CH3/CH4 SWITCH

3 4

CH.

OR

Tune

TV to

Ch.3

The CH3/CH4 switch on the VCR’s back panel determines which channel the VCR uses to send video signals to your TV.

The TV must be tuned to the same channel you set with the

CH3/CH4 switch to see tape playback and status displays from the VCR. To determine which video channel provides the best picture for your system, try the switch in CH3 position and tune your TV to channel 3; then try the CH4 position and tune your

TV to channel 4.

3 4

CH.

Tune

TV to

Ch.4

For a test display, press TV/VCR on remote repeatedly until the VCR indicator light appears in the VCR’s front panel display. Press MENU on the remote to see the main menu.

11