2
The S60 System
Introduction
The Dell Networking S60 system is a high-performance, high-capacity, low-cost, stackable, Layer 2 switch/Layer 3 router that supports 44 built-in 10/100/1000 Base-T ports, four Small Form-Factor
Pluggable (SFP) ports, an optional Small Form-Factor Pluggable Plus (SFP+) module, and optional 12G or 24G stacking modules.
The front of the S60 ( Figure 2-1 ) contains the Power Supply Units (PSUs), optional module slots, and the
grounding connectors. The rear of the S60 (
Figure 2-2
) contains the 44 ethernet ports, optional module ports, management ports, and displays for alarms and stacking identification.
Figure 2-1.
The Front of the S60 System
Ground Connectors
Mounting Bracket
Power Connector
(AC shown)
Fans
Mounting Bracket
Optional Module
(OPT1)
Power Supply (PSU0)
Figure 2-2.
The Rear of the S60 System
Power Supply (PSU1)
Stack ID
Management
Ports
Ethernet Ports
SFP Ports Alarm
LEDs
Optional
Module
(OPT0)
NOTE: The ethernet ports are labeled 0-43. When cabling these ports, be sure not to interfere with the airflow from the small vent holes above and below the ports.
The S60 System |
6
Orderable S60 Systems
You can order the S60 in several different configurations. You can order optional modules separately.
Hardware
S60: 44 port 10/100/1000 Base-T with 4 SFP ports and 2 modular slots
S60: 44 port 10/100/1000 Base-T with 4 SFP ports, 2 modular slots,1 AC PSU and 1 fan subsystem
S60: 44 port 10/100/1000 Base-T with 4 SFP ports, 2 modular slots,1 DC PSU and 1 fan subsystem
S60 Fan Subsystem with airflow from the I/O panel to the PSU
S60 Fan Subsystem with airflow from the PSU to the I/O panel
S60 AC PSU with 1 fan module
S60 AC PSU with 1 reverse-flow fan module
S60 DC PSU with 1 fan module
S60 DC PSU with 1 reverse-flow fan module
S60 2-port, 12 Gigabit stacking module
S60 1-port, 24 Gigabit stacking module
S60 2-port, 10GE SFP+ module
To successfully install the S60 system, ensure that you have the following:
• S60 chassis (or multiple chassis, if stacking)
• At least one grounded AC or DC power source per chassis
• Cable to connect the AC or DC power source to the chassis (the US AC power cable is included)
• Mounting brackets for rack installation (included)
• Screws for rack installation and #1 #2 Phillips screwdrivers (not included)
• Ground cable (not included)
• Ground cable screws (included)
• Copper/fiber cables
Other optional components are:
• Additional PSU
• Additional fan module
• Optional modules, if needed
• Stacking cables, if stacking
The S60 System |
7
Features
The S60 offers the following:
• S60 CPU and switch processor
• Up to 12 stacked systems
• Stackable switch features
• 19-inch rack-mountable
• Standard 1U chassis height
• Hot-swappable optional modules, PSUs, and fan modules
• Integrated PSU/fan module (three fans per module)
• Up to 16K MAC address entries supported with hardware-assisted aging
• Supports 9K jumbo frames
Ports
• Optional ports supporting two 2-port, 10G SFP+ modules
• 44 fixed 10/100/1000 Mbps auto-sensing and auto-MDIX RJ45 ports
• Four fixed ports supporting 100/1000 Base-T or 1000 Base-X using auto-media detection
• Optional ports supporting one 2-port, 24G stacking module or two 1-port, 12G stacking modules
• Console port
• Universal Serial Bus (USB)-A port
• USB-B port
System Status
You can view S60 status information in several ways, including physical displays and boot menu options.
You can also view status information through the Command Line Interface (CLI) show commands and with Simple Network Management Protocol (SNMP) traps. For more information about these options, refer to the FTOS Command Line Reference Guide for the S60 System and the FTOS Configuration Guide
for the S60 System.
LED Displays
As shown in Figure 2-3
, the S60 rear panel contains several sets of Light Emitting Diodes (LEDs). The
Stacking ID is at the top right corner on the rear of the system and is shown in hexidecimal form. A small decimal at the bottom right of the LED indicates the stack master.
NOTE: The stacking LED display is not applicable to the first release of the S60 system.
The S60 System |
8
Figure 2-3.
Stack ID Hexidecimal Display
• The stack master indicator displays:
• Stack Master—decimal LED ON
• Stack standby—decimal LED blinking
• Member—decimal LED Off
• Below the Stack ID LED and above the optional module ports are four LEDs that display the system
status ( Table 2-1 ). From left to right they are:
• power
• alarm
• PSU0
• PSU1
Table 2-1.
System LED Displays
Label
Power (PWR)
Power Supply
(PSU0)
Power Supply
(PSU1)
LED Color/Display
Green Blinking
Green
Yellow
Green
Yellow
Green
Yellow
Description
System is booting up.
System power supply is OK.
System power supply is operating outside the expected parameters.
All fans are OK.
At least one fan is operating outside the expected parameters.
All fans are OK.
At least one fan is operating outside the expected parameters.
The S60 System |
9
In addition to the system LEDs, each port has status indicator LEDs. Table 2-2 lists the port LED
displays.
Table 2-2.
Port LED Displays
Feature
10/100/1000 Port LEDs
SFP+ Port LED
Stacking Module LEDs
Description
• Link LED (on the left side of each port):
Green—1000M
Yellow—10/100M
Off—No link
• Activity LED (on the right side of each port):
Green—Link up on this port, full traffic
Blinking Green—Activity, transmitting or receiving packet at this port.
Off—No traffic
• Link/Activity LED:
Green—Link up on this port, no activity taking place
Blinking Green—Activity, transmitting or receiving packet at this port.
Off—No link detected at this port
• Link/Activity LED:
Green—Link up on this port, no activity taking place
Blinking Green—Activity, transmitting or receiving packet in link up state
Off—No Link detected at this port
The S60 System |
10
