Connector Description. STMicroelectronics uLink, uPSD3400 ED3K4, uPSD Turbo DK3400, rLink

UM0131
USER MANUAL
Turbo Plus uPSD DK3400 Development Kit
1
Introduction
To enhance the feature set of uPSD Turbo Family, the USB Microcontroller Development Kit
DK3400 has been released from STMicroelectronics. The kit is a demo board for the
uPSD3400 family which is a series of 8051 class microcontrollers (MCUs) that contain a fast
Turbo Plus 8032 core with 16-bit code fetch path, full-speed USB port, a large Dual Bank Flash
memory, a large SRAM, many peripherals, programmable logic and a JTAG Debug / In System
Programming (ISP) port. The DK3400 kit consists of an ED3K4 module and DK3400
motherboard as well as all the items needed to explore the uPSD3400 MCU. There are also
demonstration application examples along with an evaluation copy of the tools needed to
develop and compile code for the uPSD3400.
Figure 1.
DK3400 Contents
1.
DK3400 Motherboard
2.
ED3K4 uPSD3400 module
3.
DK3400 CD
4.
110V/220V AC adapter
5.
Plug adapters
6.
RS232 Serial Cable
7.
USB ULINK Adapter
8.
USB Cables (x2, only 1 shown):
1 for ULINK, 1 for uPSD
6
14-pin female-female ribbon
cable (JTAG)
8
9.
5
4
9
2
1
7
10. Quick Start Flyer (not shown)
March 2005
3
UM0131
Rev 1
1/32
32
Turbo Plus uPSD DK3400 Development Kit
Contents
Contents
1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2
DK3400 Hardware Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3
ED3K4 Hardware and Operation Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.1
3.2
4
5
ED3K4 Hardware Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.1.1
ED3K4 Jumpers Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.1.2
Jumpers Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.1.3
Connector Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.1.4
ED3K4 Top connection capabilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.1.5
LEDs on ED3K4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
ED3K4 Operation Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.2.1
Operation Mode 1: USB Mass Storage Mode . . . . . . . . . . . . . . . . . . . . . . . . 15
3.2.2
Operation Mode 2: uPSD+E-RLINK Mode . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.2.3
Operation Mode 3: Stand-alone RLINK mode . . . . . . . . . . . . . . . . . . . . . . . . 17
3.2.4
Operation Mode 4: uPSD+ULINK mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.2.5
Operation Mode 5: ED3K4+DK3400 Motherboard mode . . . . . . . . . . . . . . . 19
DK3400 Motherboard Hardware Architecture . . . . . . . . . . . . . . . . . . . . . . 20
4.1
Jumper description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
4.2
Connector description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Getting Started With DK3400 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Appendix A ED3K4 Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Appendix B DK3400 Motherboard Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
6
2/32
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
UM0131
Turbo Plus uPSD DK3400 Development Kit
2
DK3400 Hardware Features
DK3400 Hardware Features
The DK3400 comprises both the ED3K4 board and DK3400 motherboard. ED3K4 is able to
work as an uPSD3400 module independently or work together with DK3400 motherboard. The
DK3400 motherboard works as a base board for the ED3K4. It is possible to upgrade the
motherboard with extension boards (for example, ED3K3 and DKMMX which are currently in
development).
The DK3400 motherboard itself has a variety of hardware capabilities built-in. A number of
hardware features on the DK3400 are provided to enable exploration by the user and for future
demo application software, including (see Figure 2 and Figure 3):
●
Two selectable power sources of ED3K4: USB cable and 5V wall adapter
●
Dual USB port for E-RLINK and uPSD USB users respectively
●
Total of 100 pins for extension connector
●
One JTAG port
●
One RS232 connector
●
One small regulated 5V power jack on ED3K4 and one 9V power jack on the DK3400
motherboard
●
128 Mbit NAND Flash
●
Very small QFN package RTC from STMicroelectronics
●
8 Mbit SPI interface Flash
●
16 Kbit I2C interface EEPROM
●
Embedded debug tools RLINK
●
IrDA transceiver
●
122*32 Dot Matrix LCD with Chinese font support
●
PS/2 standard keyboard connector
UM0131
3/32
Turbo Plus uPSD DK3400 Development Kit
DK3400 Hardware Features
Figure 2.
ED3K4 Board Features
2
1
4
3
15
1.
USB port for E-RLINK
2.
USB port for uPSD user
3.
Power-on Switch
4.
Reset Switch
5.
5V power jack
6.
14-pin JTAG Connector
7.
uPSD34XX
8.
Expansion Connectors
9.
IrDA Transceiver
10.
NAND flash
11.
Real-Time Clock
12.
I2C interface EEPROM
13.
SPI interface Flash
14.
RS232 transceiver
15.
Power management
13
12
7
8
10
11
14
9
5
6
4/32
UM0131
Turbo Plus uPSD DK3400 Development Kit
Figure 3.
DK3400 Hardware Features
DK3400 Motherboard Features
7
1.
Power Switch
2.
9V Power Input
3.
Dot Matrix LCD
4.
RS232 connector
5.
PS/2 connector
6.
Connectors for ED3Kx
7.
Connectors for DKMMX
6
4
2
5
1
3
UM0131
5/32
Turbo Plus uPSD DK3400 Development Kit
ED3K4 Hardware and Operation Mode
3
ED3K4 Hardware and Operation Mode
The ED3K4 is a very low cost uPSD3400 evaluation module with full-speed USB support,
embedded debug tools RLINK and 128-Mbit NAND flash. Depending on different application
purposes, ED3K4 can be configured to one of the following 5 operation modes:
●
Mode1: USB mass storage mode
●
Mode2: uPSD3400+E-RLINK mode
●
Mode3: Stand-alone RLINK mode
●
Mode4: uPSD3400+ULINK mode
●
Mode5: ED3K4+DK3400 motherboard mode
The 5 operation modes will be introduced in detail later.
3.1
ED3K4 Hardware Architecture
The jumpers and connectors definitions on ED3K4 board are detailed in this chapter.
6/32
UM0131
Turbo Plus uPSD DK3400 Development Kit
3.1.1
ED3K4 Hardware and Operation Mode
ED3K4 Jumpers Diagram
Figure 4.
Block diagram layout of the jumper positions of the ED3K4 board
SW1
eRlink
uPSD
JP4
SW2
1
2
JP1 JP2 JP3
3
1
2
JP6
2
uPSD3400
3
1
JP5
2
3
JP7
Extension connector CN5
Extension connector CN4
Extension connector CN3
Extension connector CN2
Extension connector CN1
1 2
1
128Mbit NAND Flash
JP8 JP9 JP10
1
2
JP11
2
4
6
1
3
5
1
2
Power
JTAG connector
UM0131
JP12
IrDA
7/32
ED3K4 Hardware and Operation Mode
3.1.2
Turbo Plus uPSD DK3400 Development Kit
Jumpers Description
The definitions of the jumpers on ED3K4 board are listed in Table 1:
Table 1.
Description of jumpers on ED3K4 board
Jumper
Description
JP1 is used to enable SPI interface Flash M25P80.
JP1
M25P80 is enabled when JP1 is closed.
Default status: closed
JP2
Reserved. Please keep this jumper on open.
Default status: open
JP3 is used to enable USB auto-disconnect function.
JP3
USB auto-disconnect function is enabled when JP3 is closed.
Default status: closed
JP4 is used to select a power source for JTAG port.
Keep JP4 on following status when ED3K4 works on Mode1, 2, 4 and 5:
JP4
1
2
3
Keep JP4 on open when ED3K4 works on Mode 3.
Default status: JP4.1 connected to JP4.2
JP5 is used to select which power source will be used as USB power input of power
management circuit, power from E-RLINK USB cable or power from uPSD USB cable.
Keep JP5 on following status when ED3K4 powered from RLINK USB cable:
JP5
1
2
3
1
2
3
Keep JP5 on following status when ED3K4 powered from uPSD USB cable:
Default status: JP5.1 connected to JP5.2
JP6 is used to provide a boot option for ED3K4 board.
JP6
ED3K4 boot from internal main flash when JP6 is closed.
ED3K4 boot from internal boot flash when JP6 is open.
Default status: open
8/32
UM0131
Turbo Plus uPSD DK3400 Development Kit
ED3K4 Hardware and Operation Mode
JP7 is used to select clock generation source, external clock or internal clock.
ED3K4 works with internal clock when JP7 is set as following:
JP7
1
2
3
1
2
3
ED3K4 works on external clock mode when JP4 is set as following:
Default status: JP7.1 connected to JP7.2
JP8
JP8 is used to enable NAND Flash. 128Mbit NAND flash is enabled when JP8 is closed.
Default status: closed
JP9 is used to select JTAG circuit operation mode along with JP10 depending on
operation mode of ED3K4.
JP9
Keeps JP9 on closed when ED3K4 works on mode 1, 2, 3 and 5.
Keeps JP9 on open when ED3K4 works on mode 4.
Default status: closed
JP10 is used to select JTAG circuit operation mode along with JP9 depending on
operation mode of ED3K4.
JP10
Keeps JP10 on closed when ED3K4 works on mode 1, 2, 4 and 5.
Keeps JP10 on open when ED3K4 works on mode 3.
Default status: closed
JP11
JP11 is used to enable DEBUG signal. DEBUG signal is enabled when JP11 is closed.
Default status: open
JP12 is used to select which transceiver will be connected to UART1 port,
RS232 transceiver or IrDA transceiver.
UART1 is connected to RS232 transceiver when JP12 is set as following:
JP12
2
4
6
1
3
5
2
4
6
1
3
5
UART1 is connected to IrDA transceiver when JP12 is set as following:
Default status JP12.2 connected to JP12.4;
Default status JP12.1 connected to JP12.3.
UM0131
9/32
ED3K4 Hardware and Operation Mode
3.1.3
Turbo Plus uPSD DK3400 Development Kit
Connector Description
The definitions of connectors on ED3K4 board are listed in Table 2 and Table 3:
Table 2.
Description of connectors on ED3K4 board
Connector
POWER
USER USB
10/32
Description
Regulated 5V power jack.
Note: The absolute Maximum voltage on this jack is 6V.
USB port connected to uPSD3400 on board.
E-RLINK USB
USB port for embedded RLINK
JTAG
JTAG port used for debugging and programming
CN1, 2, 3, 4 and 5
100 pins Extension connectors for user.
UM0131
Turbo Plus uPSD DK3400 Development Kit
Table 3.
Description of the 100-pin extension connector CN1,2,3,4 and 5
Connector
Signal Name
CN2
Pins
Description
RD#
1
READ signal
WR#
2
WRITE signal
GND
CN1
ED3K4 Hardware and Operation Mode
3,4,5,6,7,8
9,10,11
Ground
MCU_AD0
12
Multiplexed Address/Data bus A0/D0
MCU_AD1
13
Multiplexed Address/Data bus A1/D1
MCU_AD2
14
Multiplexed Address/Data bus A2/D2
MCU_AD3
15
Multiplexed Address/Data bus A3/D3
MCU_AD4
16
Multiplexed Address/Data bus A4/D4
MCU_AD5
17
Multiplexed Address/Data bus A5/D5
MCU_AD6
18
Multiplexed Address/Data bus A6/D6
MCU_AD7
19
Multiplexed Address/Data bus A7/D7
PSEN#
20
PSEN signal external bus
PC2/VSTBY
1
GPIO/PLD Output or Input/SRAM standby
voltage input(Vstby)
GND
2,19
Ground
VCC1
3,4,5,6,7,8
External 5V wall adapter power source (56V)
PA7
9
GPIO on port A
PA6
10
GPIO on port A
PA5
11
GPIO on port A
PA4
12
GPIO on port A
PWR_DOWN
13,17
Reserved
PA3
14
GPIO on port A
PA2
15
GPIO on port A
P34/C0
16
GPIO/Counter 0 input
VBATT
18
Reserved
EXT_CLK
20
External clock input
UM0131
11/32
Turbo Plus uPSD DK3400 Development Kit
ED3K4 Hardware and Operation Mode
PC3/TSTAT
CN3
12/32
GPIO/optional JTAG status(TSTAT)
MCU_SPI_SEL
2
SPI slave select signal
MCU_SPI_TXD
3
SPI TXD signal
MCU_SPI_RXD
4
SPI RXD signal
MCU_SPI_CLK
5
SPI clock signal output
P42/TCM2
6
GPIO/PCA0-TCM2/UART1 RXD signal
P41/TCM1
7
GPIO/PCA0-TCM1/Timer 2 trigger input
P40/TCM0
8
GPIO/PCA0-TCM0/Timer 2 counter input
P32/INT0
9
GPIO/External interrupt0 input
P33/INT1
10
GPIO/External interrupt1 input
P11/T2X
11
GPIO/Timer 2 trigger input/ADC channel 1
GND
12,17
Ground
TXD1_232
13
UART1 TXD signal on RS232 voltage level
RXD1_232
14
UART1 RXD signal on RS232 voltage level
PA1
15
GPIO on port A
PA0
16
GPIO on port A
P36/SDA
18
GPIO/I2C Bus serial data
P37/SCL
19
GPIO/I2C Bus clock
VCC3
20
3.3V power
CPU_DEBUG
1
I/O to the MCU Debug Unit
PC7
2
GPIO/PLD input and output
PD1
3
GPIO/PLD IO
PB0
4
GPIO/PLD IO/Address Latch output
P31/TXD0
5
GPIO/UART0 transmit TXD signal
P30/RXD0
6
GPIO/UART0 receive RXD signal
GND
CN4
1
7,13,15,17
19
Ground
TXD0_232
8
UART0 TXD signal on RS232 voltage level
RXD0_232
9
UART0 TXD signal on RS232 voltage level
PC4/TERR#
10
GPIO/Optional JTAG status(TERR)
P35/C1
11
GPIO/Counter1 input
VCC2
12
5V power
P17/AD7
14
GPIO/SPI slave select/ADC channel 7
P15/AD5
16
GPIO/SPI receive/ADC channel 5
P13/AD3
18
GPIO/UART1 or IrDA transmit/ADC
channel 3
RESET#
20
System reset signal
UM0131
Turbo Plus uPSD DK3400 Development Kit
ALE
CN5
3.1.4
ED3K4 Hardware and Operation Mode
1
Address latch signal
PD2
2
GPIO/PLD input and output
PB0
13
GPIO/PLD IO/Address Latch output
PB1
3,12
GPIO/PLD IO/Address Latch output
PB2
4,11
GPIO/PLD IO/Address Latch output
PB3
5,10
GPIO/PLD IO/Address Latch output
PB4
6
GPIO/PLD IO/Address Latch output
PB5
7
GPIO/PLD IO/Address Latch output
PB6
8
GPIO/PLD IO/Address Latch output
PB7
9
GPIO/PLD IO/Address Latch output
VCC2
14
5V power
P16/ADC6
15
GPIO/SPI transmit/ADC channel 6
VCC3
16,18
3.3V power
P14/ADC4
17
GPIO/SPI clock output/ADC channel 4
P12/ADC2
19
GPIO/UART1 or IrDA receive/ADC channel
2
P10/ADC0
20
GPIO/Timer 2 counter input/ADC channel
0
ED3K4 Top connection capabilities
Various external connectivity is provided based on 100-pin connector on ED3K4, including 7
channels of ADC, 6 channels of PWM/SERVO output, 3 channels of Timing capture, SRAM
backup power input, UART1 RS232 level, UART0 digital level, POWER-DOWN input, External
battery, External clock, I2C and External RESET. All possible top connection capabilities have
been listed in following Table 4.
Table 4.
ED3K4 Top connection capabilities
Capabilities
SRAM backup power
PWM/SERVO OUTPUT1
PWM/SERVO OUTPUT2
PWM/SERVO OUTPUT3
PWM/SERVO OUTPUT4
Signals name
Headers
PC2/VSTBY
CON2.1
GND
CON2.2
GND
CON1.3
VCC1
CON2.3
MCU_SPI_TXD
CON3.3
GND
CON1.4
VCC1
CON2.4
MCU_SPI_RXD
CON3.4
GND
CON1.5
VCC1
CON2.5
MCU_SPI_CLK
CON3.5
GND
CON1.6
VCC1
CON2.6
P42/TCM2
CON3.6
UM0131
13/32
Turbo Plus uPSD DK3400 Development Kit
ED3K4 Hardware and Operation Mode
GND
PWM/SERVO OUTPUT5
PWM/SERVO OUTPUT6
TIMING CAPTURE 1
TIMING CAPTURE 2
TIMING CAPTURE 3
UART1 RS232 level
POWER-DOWN
EXTERNAL BATTERY CONNECTION
EXTERNAL CLOCK INPUT
I2C BUS WITH GND+POWER
UART0 DIGITAL LEVEL
ADC channel 1
ADC channel 2
ADC channel 3
ADC channel 4
ADC channel 5
ADC channel 6
14/32
CON1.7
VCC1
CON2.7
P41/TCM1
CON3.7
GND
CON1.8
VCC1
CON2.8
P40/TCM0
CON3.8
GND
CON1.9
PA7
CON2.9
P32/INT0
CON3.9
GND
CON1.10
PA6
CON2.10
P33/INT1
CON3.10
GND
CON1.11
PA5
CON2.11
P11/T2X
CON3.11
TXD1_232
CON3.13
RXD1_232
CON3.14
PWR_DOWN
CON2.17
GND
CON3.17
VBATT
CON2.18
GND
CON2.19
EXT_CLK
CON2.20
GND
CON2.19
GND
CON3.17
P36/SDA
CON3.18
P37/SCL
CON3.19
VCC3
CON3.20
P31/TXD0
CON4.5
P30/RXD0
CON4.6
GND
CON4.7
P11/T2X
CON3.11
GND
CON3.12
P12/ADC2
CON5.19
GND
CON4.19
P13/ADC3
CON4.18
GND
CON4.19
P14/ADC4
CON5.17
GND
CON4.17
P15/ADC5
CON4.16
GND
CON4.17
P16/ADC6
CON5.15
GND
CON4.15
UM0131
Turbo Plus uPSD DK3400 Development Kit
P17/ADC7
ADC channel 7
EXTERNAL RESET
3.1.5
ED3K4 Hardware and Operation Mode
CON4.14
GND
CON4.13
RESET#
CON4.20
GND
CON4.19
LEDs on ED3K4
There are 7 LEDs to indicate the work status on ED3K4 board. D5 and D8 are driven by Power
management chips. LD1, LD2 and LD3 are used to indicate the work status of the embedded
Rlink. D2 is used to indicate the JTAG operation. D6 is a user LED that can be driven by uPSD
PD1. All the LEDs D5, D6, D8, LD1, LD2 and LD3 are located on the area near by the eRlink
USB port. D2 is located on the area near the POWER connector. Please find the detailed
information in Table 5.
Table 5.
LED description
LED
3.2
Color
Usage
D2
red
JTAG operation indicator LED
D5
red
Power indicator LED
D8
red
Low battery indicator LED
LD1
green
eRlink Power indicator LED
LD2
red
eRlink BUSY indicator LED
LD3
green
eRlink RUN indicator LED
D6
red
User LED that can be driven by uPSD3434E on board
ED3K4 Operation Mode
The ED3K4 is a versatile uPSD3400 module with 5 user operation modes. You may treat it as a
uPSD3400 user target board, standalone debug tools RLINK or an integrated uPSD3400
development platform with embedded SW evaluation capability depending on the relative
configuration and usage. The 5 operation modes will be introduced in the following chapter one
by one.
3.2.1
Operation Mode 1: USB Mass Storage Mode
The ED3K4 module may be used as a low speed USB device with file storage function on
operation mode1. Connected to PC with WinXP via a USB cable, it can be used to download
and upload files to or from the ED3K4 module.
UM0131
15/32
Turbo Plus uPSD DK3400 Development Kit
ED3K4 Hardware and Operation Mode
Figure 5.
ED3K4 operation mode 1 connection
-A
3400
uPSD
USB-B
(2x)
JTAG
NAND
-A
PC HOST
eRlink
TOP SIDE
Hardware connection on Mode 1
Please refer to Figure 5 for the connection on operation mode 1.
Configuration of jumpers on Mode 1
Please refer to Table 6 for detailed information about jumper configuration on operation mode 1.
Table 6.
Jumper configuration on Mode 1
Jumper
3.2.2
Status
Jumper
Status
Jumper
Status
JP1
closed
JP5
1<->2
JP9
closed
JP2
open
JP6
closed
JP10
closed
JP3
closed
JP7
1<->2
JP11
open
JP4
1<->2
JP8
closed
JP12
1<->3;2<->4
Operation Mode 2: uPSD+E-RLINK Mode
The ED3K4 module may be used as integrated uPSD3400 development platform with
embedded RLINK on operation mode2. You can build the small uPSD3400 platform by simply
connecting the ED3K4 to a PC with RIDE via a USB cable.
Figure 6.
ED3K4 operation mode 2 connection
-A
uPSD
USB-B
(2x)
16/32
3400
user
TOP SIDE
UM0131
JTAG
eRlink
NAND
-A
PC HOST
debug
Turbo Plus uPSD DK3400 Development Kit
ED3K4 Hardware and Operation Mode
Hardware connection on Mode 2
Please refer to Figure 6 for the connection on operation mode 2.
Configuration of jumpers on Mode 2
Please refer to Table 7 for detailed information about jumper configuration on operation mode 2.
Table 7.
Jumper configuration on Mode 2
Jumper
3.2.3
Status
Jumper
Status
Jumper
Status
JP1
closed
JP5
2<->3
JP9
closed
JP2
open
JP6
closed
JP10
closed
JP3
closed
JP7
1<->2
JP11
open
JP4
1<->2
JP8
closed
JP12
1<->3;2<->4
Operation Mode 3: Stand-alone RLINK mode
The ED3K4 module may be used as a stand-alone uPSD debug tool like RLINK on operation
mode3. Only the embedded RLINK is active on ED3K4 board on this operation mode.
Figure 7.
ED3K4 operation mode 3 connection
-A
USB-B
(2x)
JTAG
3400
uPSD
NAND
eRlink
-A
PC HOST
debug
Standard
14-pin cable
ED3K4
JTAG
uPSD
uPSD Target Board
Hardware connection on Mode 3
Please refer to Figure 7 for the connection on operation mode 3.
Configuration of jumpers on Mode 3
Please refer to Table 8 for detailed information about jumper configuration on operation mode 3.
Table 8.
Jumper
JP1
Jumper configuration on Mode 3
Status
closed
Jumper
JP5
Status
1<->2
UM0131
Jumper
JP9
Status
closed
17/32
Turbo Plus uPSD DK3400 Development Kit
ED3K4 Hardware and Operation Mode
3.2.4
JP2
open
JP6
closed
JP10
open
JP3
closed
JP7
1<->2
JP11
open
JP4
open
JP8
closed
JP12
1<->3;2<->4
Operation Mode 4: uPSD+ULINK mode
The ED3K4 module may be treated as a uPSD target board on operation mode4. The
embedded RLINK on board is disabled in this mode. You may connect ED3K4 with another
JTAG-based uPSD debug tools like ULINK from Keil in this mode.
Figure 8.
ED3K4 operation mode 4 connection
-A
3400
uPSD
USB-B
(2x)
JTAG
user
NAND
-A
PC HOST
eRlink
Standard
14-pin cable
ED3K4
JTAG
debug
ULINK
Hardware connection on Mode 4
Please refer to Figure 8 for the connection on operation mode 4.
Configuration of jumpers on Mode 4
Please refer to Table 9 for detailed information about jumper configuration on operation mode
4.
Table 9.
Jumper
18/32
Jumper configuration on Mode 4
Status
Jumper
Status
Jumper
Status
JP1
closed
JP5
1<->2
JP9
open
JP2
open
JP6
closed
JP10
closed
JP3
closed
JP7
1<->2
JP11
open
JP4
1<->2
JP8
closed
JP12
1<->3;2<->4
UM0131
Turbo Plus uPSD DK3400 Development Kit
3.2.5
ED3K4 Hardware and Operation Mode
Operation Mode 5: ED3K4+DK3400 Motherboard mode
The ED3K4 module is capable of working together with the DK3400 motherboard in operation
mode 5. The dot-matrix LCD, RS232 connector and PS/2 Keyboard are available for use in this
operation mode. The default DK3400 will be delivered with mode 5. You are allowed to program
and debug DK3400 using alternative JTAG debug tools, embedded Rlink or external ULINK on
mode 5. Please make sure that the jumper configuration of JP9 and JP10 is compatible with
requirement in mode 2 when you select eRlink as debug tools. Please also make sure that the
jumper configuration of JP9 and JP10 is compatible with requirement in mode 4 when you
select external ULINK as debug tools.
Hardware connection on Mode 5
Just plug ED3K4 module in the ED3Kx socket on DK3400 motherboard.
Configuration of jumpers on Mode 5
Please refer to Table 10 for detailed information about jumper configuration on operation mode
5.
Table 10.
Jumper
Jumper configuration on Mode 5
Status
Jumper
Status
Jumper
Status
JP1
closed
JP5
open
JP9
closed
JP2
open
JP6
open
JP10
closed
JP3
closed
JP7
1<->2
JP11
open
JP4
1<->2
JP8
closed
JP12
1<->3;2<->4
UM0131
19/32
DK3400 Motherboard Hardware Architecture
4
Turbo Plus uPSD DK3400 Development Kit
DK3400 Motherboard Hardware Architecture
The DK3400 motherboard can be used as a base board for both the uPSD module ED3K4 and
ED3K3. The power supply, LCD, RS232 interface and PS/2 Keyboard interface are available on
this board.
4.1
Jumper description
The jumper definitions on the DK3400 motherboard are listed in Table 11.
Table 11.
Description of jumpers on DK3400 motherboard
Jumper
Description
JP1 is used to select which UART port is connected to RS232 connector on DK3400
motherboard.
UART0 is connected to RS232 connector when JP1 is set as following:
JP1
4
6
1
3
5
2
4
6
1
3
5
UART1 is connected to RS232 connector when JP1 is set as following:
Default status:
JP1.3 connected to JP1.5;
JP1.4connected to JP1.6.
20/32
2
UM0131
Turbo Plus uPSD DK3400 Development Kit
4.2
DK3400 Motherboard Hardware Architecture
Connector description
The connector definitions on the DK3400 motherboard are listed in Table 12.
Table 12.
Description of connectors on DK3400 motherboard
Connector
Description
CN0
9V power jack.
CN1,2,3,4 and 5
Connectors for ED3Kx module
CN6
RS232 connector (female)
CN7
PS/2 standard Keyboard connector
DKMMX_CON1
Connector for DKMMX board
DKMMX_CON2
Connector for DKMMX board
DKMMX_CON3
Connector for DKMMX board
UM0131
21/32
Turbo Plus uPSD DK3400 Development Kit
Getting Started With DK3400
5
Getting Started With DK3400
The DK3400 is delivered in default operation mode 5 with the RTC demonstration application.
Please follow the steps below to get started using the DK3400:
Check with Jumper configuration
Please check the jumper configuration to guarantee that all jumper status are the same as
those listed in Table 10 (ED3K4 operation mode 5).
Connecting DK3400 board for RTC demo
1.
Connect the AC adapter to the DK3400 board. The DK3400 AC adapter will work on either
110V or 220V, and contains several different plug adapters to fit popular European AC
outlets. Please set up your AC adapter to fit your AC plug type and plug in the AC adapter.
Then plug the small power plug into the DK3400 9V DC input.
2.
Connect a PS/2 standard Keyboard to PS/2 connector on DK3400 motherboard.
Step 3 - Try Your DK3400 Board with RTC demo.
Turn DK3400 on. Your DK3400 board will boot from RTC demo application.
You should see the DK3400 RTC demo running in the LCD window. The RTC time can be
updated by pressing keys “up”, “down”, “left”, “right” and “enter” on the Keyboard.
Additional Information
The uPSD3400 series design guide application notes for DK3400 using RIDE or KEIL's
software tools are available for download from the ST website:
http://www.st.com/psm
22/32
UM0131
UM0131
A
B
C
D
1
1
RLINK
RLINK.SCH
JTAG
JTAG.SCH
Peripherals
Peripherals.SCH
MC U
MC U.SCH
Power
Power.SCH
IO
IO. SCH
2
2
3
3
Date:
A4
Size
Title
4
ED3K4
23-Feb-2005
Number
4
Revision 1.1
A
B
C
D
Turbo Plus uPSD DK3400 Development Kit
Getting Started With DK3400
Appendix A ED3K4 Schematic
23/32
UM0131
A
B
C
D
2
R35
36K
R34
10K
5V_UDI SK
1
1
VCC3
T1
9013
RD#
WR#
GND
GND
GND
GND
GND
GND
GND
GND
GND
MC U_AD0
MC U_AD1
MC U_AD2
MC U_AD3
MC U_AD4
MC U_AD5
MC U_AD6
MC U_AD7
PSEN#
3
24/32
1
VCC
DD+
GND
SHELL
SHELL
User USB
USB- B
CON20
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
CN1
1K
R5
1
2
3
4
5
6
5V_UDISK
R4
510
PC7
22
R3
22
R2
C1
104
PC2/VSTBY
GND
VCC1
VCC1
VCC1
VCC1
VCC1
VCC1
PA7
PA6
PA5
PA4
PWR_DOWN
PA3
PA2
P34/C0
PWR_DOWN
VBATT
GND
EXT_CLK
CON20
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
CN2
1
2
JP3
2
MC U_USBD+
MC U_USBD-
2
USB- B
Program/Debug
1
VCC
2
D3
D+
4
GND
5
SHELL
6
SHELL
CON20
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
CN3
RLINK_USBDRLINK_USBD+
5V_RLINK
PC3/TSTAT
M CU_SPI_SE L
MC U_SPI _TXD
MC U_SPI _RXD
M CU_SPI_CLK
P42/TCM 2
P41/TCM 1
P40/TCM 0
P32/INT0
P33/INT1
P11/T2X
GND
TXD1_232
RXD1_232
PA1
PA0
GND
P36/SDA
P37/SCL
VCC3
R1
1k5
5V_RLINK
3
CPU_DEBUG
PC7
PD1
PB0
P31/TXD0
P30/RXD0
GND
TXD0_232
RXD0_232
PC4/TERR#
P35/C1
VCC2
GND
P17/ADC7
GND
P15/ADC5
GND
P13/ADC3
GND
RESET#
3
Date:
A4
Size
Title
CON20
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
CN4
4
23-Feb-2005
Number
CONNECTOR
VCC2
P16/ADC6
VCC3
P14/ADC4
VCC3
P12/ADC2
P10/ADC0
ALE
PD2
PB1
PB2
PB3
PB4
PB5
PB6
PB7
CON20
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
CN5
4
Revision 1.1
A
B
C
D
Getting Started With DK3400
Turbo Plus uPSD DK3400 Development Kit
UM0131
A
B
C
1
2
1
JP9
2
1
JP10
PC3/TSTAT
PC4/TERR#
PC6/TDO
GND
RLINK_TDI
RLINK_TM S
RLINK_TCK
RLINK_RST
R32
R33
2
4
6
8
11
13
15
17
1
19
1Y1
1Y2
1Y3
1Y4
2Y1
2Y2
2Y3
2Y4
74VHC244T
1A1
1A2
1A3
1A4
2A1
2A2
2A3
2A4
1E
2E
U10
JTAG_VCC
20
VCC
GND
4K7
4K7
PC5/TDI
PC0/TM S
PC1/TCK
RESET#
1
2
3
RLINK_TSTAT
RLINK_TERR
RLINK_TDO
VCC2
18
16
14
12
9
7
5
3
JTAG_VCC
5V_RLINK
JTAG_VCC
10
2
2
BAT54S
1
2
3
JP4
CPU_DEBUG
8
7
6
5
RR1
10K
RLINK_CNTL
1
2
3
4
VCC2
8
7
6
5
10K
RR2
3
3
D2
RED
R6
470
JTAG_CNTL
RLINK_TRST
VCC2
1
2
3
4
D
1
Date:
A4
Size
Title
14
12
10
8
6
4
2
4
23-Feb-2005
Number
13
11
9
7
5
3
1
RLINK_JEN
TDO
TCK
TM S
VCC
TDI
GND
JEN
JTAG
TERR
GND
GND
RST
TSTAT
CNTL
TRST
JTAG
C2
104
Revision 1.1
JTAG_VCC
4
A
B
C
D
Turbo Plus uPSD DK3400 Development Kit
Getting Started With DK3400
25/32
A
B
C
1
PWR_DOWN
M CU_SPI_CL K
MC U_SPI _RXD
MC U_SPI _TXD
M CU_SPI_SE L
1
2
JP11
P40/TCM 0
P41/TCM 1
P42/TCM 2
GND
P10/ADC0
P11/T2X
P12/ADC2
P13/ADC3
P14/ADC4
P15/ADC5
P16/ADC6
P17/ADC7
AVC C
VCC2
33
31
30
27
25
23
19
18
70
72
69
52
54
56
58
59
60
61
64
75
77
79
2
40
42
44
46
P30/RXD0
P31/TXD0
P32/INT0
P33/INT1
P34/C0
P35/C1
P36/SDA
P37/SCL
68
RESET#
8
49
MC U_X2
CPU_DEBUG
JTAG_CNTL
48
MC U_X1
uPSD3400-80
VCC3
T2/ TCM 0/P4.0
T2x/ TCM 1/P4.1
RXD2/ TCM 2/P4.2
TXD2/ PCA0/ P4.3
SPISCL K/ TCM 3/P4.4
SPIRXD/ TCM 4/P4.5
SPIT XD/ TCM 5/P4.6
SPISSEL/ PCA1/ P4.7
Vref
AVC C
AGND+P SDGND
ADC0/ T2/ P1.0
ADC1/ T2x/ P1.1
ADC 2/RXD2/ P1.2
ADC 3/TXD2/ P1.3
ADC4/ SPISCL K/ P1.4
ADC 5/SPIRXD/P1. 5
ADC 6/SPITXD/P1. 6
ADC7/ SPISSEL/ P1.7
RXD/P3. 0
TXD/P3. 1
EXINT0/ GATE0/P3. 2
EXINT1/ GATE1/P3. 3
T0/ P3.4
T1/ P3.5
I2CSDA/P3. 6
I2CSCL/ P3.7
DEBUG
RESET_I N
X2
X1
U1
PB0
PB1
PB2
PB3
PB4
PB5
PB6
PB7
PA0
PA1
PA2
PA3
PA4
PA5
PA6
PA7
CTRL0/ WR
CTRL1/ RD
CTRL2/ PSEN
ALE(PD0)
P2.0/A8
P2.1/A9
P2.2/A10
P2.3/A11
P0.0/AD0
P0.1/AD1
P0.2/AD2
P0.3/AD3
P0.4/AD4
P0.5/AD5
P0.6/AD6
P0.7/AD7
2
WR#
RD#
PSEN#
ALE
PA0
PA1
PA2
PA3
PA4
PA5
PA6
PA7
PB0
PB1
PB2
PB4
PB5
PB6
PB7
PC0/TM S
PC1/TCK
PC2/VSTBY
PC3/TSTAT
PC4/TERR#
PC5/TDI
PC6/TDO
PC7
PD1
PD2
35
34
32
28
26
24
22
21
80
78
76
74
73
71
67
66
20
17
16
15
9
7
6
5
3
1
MC U_AD0
MC U_AD1
MC U_AD2
MC U_AD3
MC U_AD4
MC U_AD5
MC U_AD6
MC U_AD7
62
65
63
4
51
53
55
57
36
37
38
39
41
43
45
47
MC U_USBDMC U_USBD+
PD1
PD2
TM S/PC0
TCK/ PC1
Vst by/ PC2
TSTAT/PC3
TERR / VBATON/ PC4
TDI/ PC5
TDO/PC6
PC7
2
R31
4K7
VCC2
PB3
GND
3
BOOT Option
2
1
JP6
VCC2
3
C5
104
VCC3
2
X1
MC U_X2
C3
104
C4
104
Date:
A4
Size
Title
SW1
4
103
C14
MCU
23-Feb-2005
Number
2.2uH
L1
20pf
C10
20pf
C8
RESET#
X3
40MHZ
Reset button
CON3
1
2
3
JP7
Delete RC reset circuit
MC U_X1
EXT_CLK
CSTCW-X
VCC2
1
3
D
1
VCC
VDD
VDD
10
12
50
GND
GND
13
29
USB+
USB11
14
2
UM0131
3
26/32
GND
1
5
4
4
Revision1.1
A
B
C
D
Getting Started With DK3400
Turbo Plus uPSD DK3400 Development Kit
A
B
C
D
2
1
JP1
P33/INT1
VCC3
P37/SCL
1
R10
10K
VCC3
1
2
3
4
VCC3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
NAND0 1GW3A
NC
NC
NC
NC
NC
NC
R/B
/RE
/CE
NC
NC
Vcc
Vss
NC
NC
CLE
ALE
/WE
/WP
NC
NC
NC
NC
NC
U3
M 25P80
S
Q
W
Vss
U5
Vcc
HOLD
C
D
8
7
6
5
M CU_SPI_CL K
MC U_SPI _TXD
VCC3
SPI Interface code Flash
P34/C0
P35/C1
P36/SDA
P32/INT0
C13
104
R7 R8 R9
10K 10K 10K
C19
104
M CU_SPI_SE L
SPI_SEL
MC U_SPI _RXD
VCC3
JP8
VCC3
P42/TCM 2
C11
104
2
1
C34
6pf
NC
NC
NC
NC
IO7
IO6
IO5
IO4
NC
NC
NC
Vcc
Vss
NC
NC
NC
IO3
IO2
IO1
IO0
NC
NC
NC
NC
2
VCC3
P37/SCL
P36/SDA
C9
104
R13 R14
4.3K 4.3K
VCC3
3
4
P12/ADC2
P13/ADC3
P30/RXD0
P31/TXD0
RS232, IrDA
6
5
2
1
SW2-SPDT
JP12
1
2
3
4
M 24CXX
E0
E1
E2
Vss
U9
XI
XO
SCL
SDA
1N4148
D9
Vcc
WC
SCL
SDA
VCC3
8
7 P41/TCM 1
6 P37/SCL
5 P36/SDA
RESET#
11 RTC_ALARM
4
TP1
TP2
0.22F
IRQ/OUT
SQW
U6
M 41T6X
C7
I2C interface RTC and EEPROM
1
2
10
9
VCC3
C35
6pf
P13/ADC3
P12/ADC2
P11/T2X
P10/ADC0
VCC3
P17/ADC7
P16/ADC6
P15/ADC5
P14/ADC4
M C306
X2
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
1Gbit NAND Flash
2
14
Vs s VCC
Vs s
3
5
UM0131
+
1
3
3
VCC3
C12
104
C20
4.7uF
VCC3
Date:
A4
Size
Title
C22
104
4
VCC3
47
C21
4.7uF
ST3232
V-
R2out
T2i n
R1out
T1i n
C1-
C1+
V+
Number
15
8
7
RXD1_232
TXD1_232
13 RXD0_232
14 TXD0_232
4
5
16
VCC3
C16
105
5
C23
104
R11
1
2
6
7
8
3
4
5
Revision 1.1
TFDU4300
Anode (VCC2)
Cathode
VCC1
Vlogic
GND
TxD
RxD
SD
U4
IrDA Interface Circuit (disable shutdown)
GND
R2i n
T2out
R1i n
T1out
C2+
C2-
VCC
PERIPHERALS
6
9
10
12
11
3
1
2
23-Feb-2005
R12
C18
105
C17
105
C15
105
U2
4
A
B
C
D
Turbo Plus uPSD DK3400 Development Kit
Getting Started With DK3400
27/32
28/32
UM0131
A
B
C
D
VCC1
CON3
3
2
1
JP5
POW ER
POW ER
VBATT
C29
105
R21
1
C25
4.7uF
R24
1.24K
R22
3.32K
1
VCC1
TP6
R30
806K
R18
1K
R25
2.49K
C26
10uF
Vm ax
VCC1
R28
2.49M
C24
104
D Schottk y
D7
5V_RLINK
5V_USB
5V_UDI SK
1
2
3
1
1K
R17
D6
RED
Vm ax
10K
R15
D8
RED
JP2
Jumper for charg e
2
1
17
16
9
3
2
4
11
10
8
6
5
LTC3455
AO
AI
Vbat
TI M ER
PROG
CHRG
WALLFB
Vm ax
USB
SUSPEND
USBHP
U8
2
2
FB1
GND
SW1
FB2
HSI
SW2
ON
HSO
MODE
HOSN
ON2
PWRON
RST
PBSTAT
4.7uH
L2
1
25
7
4.7uH
L3
L4
3
2
Vm ax
100uH
GND
TP5
R27
80.6K
R29
C31 249K
10pF
R26
80.6K
R23
C30 423.1K
10pF
RTC_ALARM
VCC3
R19 3K
L2/L3
NL322522T
-4R7J(T DK)
18
13
12
24
14
21
15
19 Vm ax
22 PWR_DOWN
20 RESET# R20
23
1M
VCC3
SW2
C28
10uF
C27
10uF
1
5
4
RED
D5
C32
22u
3
1K
R16
TP4
VCC3
TP3
VCC2
VCC2
C33
104
VCC3
AVCC
3
Date:
A4
Size
Title
4
POWER
23-Feb-2005
Number
4
Revision1.1
A
B
C
D
Getting Started With DK3400
Turbo Plus uPSD DK3400 Development Kit
A
B
C
1
X4
LC7
104
LC11
33pF
33pF
HC-49 / 12M Hz
LC12
2
D
1
2
5V_RLINK
LC4
104
5V_RLINK
1
ST7_RESET
DNG_ VPP
RLINK_USBDRLINK_USBD+
DNG_ ICCDATA
DNG_ ICCCLK
LC13
103
JTAG_VCC
58
57
56
55
54
53
52
10
9
8
49
48
47
46
45
51
50
63
64
1
4
5
2
3
PF6 (H S) / ICCD ATA
PF5 (H S) / ICCCLK
PF4 (H S) / USBEN
PF3 / AIN1
PF2 / AIN0
PF1 (H S) / SDA
PF0 (H S) / SCL
PE7 (H S) / DTC
PE6 (H S) / DTC
PE5 (H S) / DTC
PE4 / PWM 1
PE3 / PW M 0 / A IN7 / D TC
PE2 (HS) / AIN6 / DTC
PE1 (HS) / AIN5 / DTC
PE0 (HS) / AIN4 / DTC
RESET
VPP / ICCSE L
OSCI N
OSCOUT
USBVSS
USBVCC
USBVDD
USBDM
USBDP
LU1
VDDF = 2.8, 3.3, 3.4, 3. 5Ilo ad max = 50 mA
104
LC8
USBVCC
LC5
104
1
2
1
5V_RLINK
PB7 /
PB6 /
PB5 /
PB4 /
PB3 /
PB2 /
PB1 /
PB0 /
PA7 /
PA6 /
PA5 /
PA4 /
PA3 /
PA2 /
PA1 /
PA0 /
DTC
DTC
DTC
DTC
DTC
DTC
DTC
DTC
DTC
DTC
DTC
DTC
DTC
DTC
DTC
DTC
2
ST7265xA RxT1
PD7 / AIN3
PD6 / AIN2
PD5 / OCMP2
PD4 / OCMP1
PD3
PD2
PD1
PD0
PC7 / DTC
PC6 / DTC
PC5 / DTC
PC4 / DTC
PC3 (H S) / DTC / SCK
PC2 (H S) / DTC / MOSI
PC1 (H S) / DTC / MISO
PC0 (H S) / MCO / SS
2
44
43
42
41
40
39
38
37
36
35
34
33
30
29
28
27
18
17
16
15
14
13
12
11
26
25
24
23
22
21
20
19
LR3
330
LR2
330
VDDF_MES
RLINK_TCK
RLINK_TDI
RLINK_TDO
RLINK_TMS
RLINK_TRST
RLINK_TSTAT
JTAG_CNTL
RLINK_TERR
RLINK_RST
RLINK_JEN
2
2
5V_RLINK
Green
LD3
Red
LD2
LR4
10k
LC6
104
LR5
10k
USB interface
LC10
10uF
1
2
1
1
2
31
59
VDD1
VDD2
VSS1
VSS2
2
1
2
LR7
10k
1
1
3
5V_RLINK
LR6
10k
JTAG_VCC
3
LR8
10k
Date:
A4
Size
Title
4
LR9
100k
23-Feb-2005
Number
1
2
3
4
5
6
7
8
RLINK
CON8
RLINK
Green
LD1
330
LR1
5V_RLINK
1
2
6
60
VDDf
VDDA
VSSf
VSSA
7
61
UM0131
32
62
DNG_ VPP
GND
DNG_ ICCDATA
GND
DNG_ ICCCLK
GND
ST7_RESET
VDDF_MES
Dongl eprogrammin g
1
2
3
4
5
6
7
8
LR11
100k
LR10
100k
JTAG_VCC
4
Revision1.1
5V_RLINK
A
B
C
D
Turbo Plus uPSD DK3400 Development Kit
Getting Started With DK3400
29/32
UM0131
A
B
C
D
CN0
RD#
WR#
GND
GND
GND
GND
GND
GND
GND
GND
GND
MC U_AD0
MC U_AD1
MC U_AD2
MC U_AD3
MC U_AD4
MC U_AD5
MC U_AD6
MC U_AD7
PSEN#
6
8
9
4
PB4
PB5
PB6
PB7
1
10
11
12
13
14
15
16
17
PA0
PA1
PA2
PA3
PA4
PA5
PA6
PA7
CON20
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
1
SW1
PC2/VSTBY
GND
VCC1_6V
VCC1_6V
VCC1_6V
VCC1_6V
VCC1_6V
VCC1_6V
PA7
PA6
PA5
PA4
PWR_DOWN
PA3
PA2
P34/C0
PWR_DOWN
VBATT
GND
EXT_CLK
VDD
V0
VSS
RST
NC
NC
CON20
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
CN2
LCD_GXM 12232SL
E2
E1
R/W
D/I(A 0)
D0
D1
D2
D3
D4
D5
D6
D7
LCD
3
2
1
CN1
2
3
1
18
7
5
D2
1N4004
VCC2_5V
C4
104P
VCC2_5V
D1
1N4004
PC3/TSTAT
M CU_SPI_SEL
MC U_SPI_TXD
MC U_SPI_RXD
M CU_SPI_CL K
P42/TCM 2
P41/TCM 1
P40/TCM 0
P32/INT0
P33/INT1
P11/T2X
GND
TXD1_232
RXD1_232
PA1
PA0
GND
P36/SDA
P37/SCL
VCC3
LCD
1N4004
1N4004
D4
D3
CON20
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
CN3
2
5
1
TXD1_232
RXD0_232
RXD1_232
2
6
C2
C1
104P
100uF/25V
1
TXD0_232
+9V
CPU_DEBUG
PC7
PD1
PB0
P31/TXD0
P30/RXD0
GND
TXD0_232
RXD0_232
PC4/TERR#
P35/C1
VCC2_5V
GND
P17/ADC7
GND
P15/ADC5
GND
P13/ADC3
GND
RESET#
2
UAR T
JP1
Vin
U1
L7806
CON20
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
CN4
3
4
C3
104P
VCC1_6V
3
GND
1
6
2
7
3
8
4
9
5
DB9
CN6
ED3K4
CON20
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
CN5
POWER
Vout
ALE
PD2
PB1
PB2
PB3
PB4
PB5
PB6
PB7
PB3
PB2
PB1
PB0
VCC2_5V
P16/ADC6
VCC3
P14/ADC4
VCC3
P12/ADC2
P10/ADC0
GND
30/32
2
UART
GND
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
3
R1
4.7K
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
VCC2_5V
R2
4.7K
Date:
A4
Size
Title
1
2
3
4
5
6
4
P34/C0
P33/INT1
23-Feb-2005
Number
DK3400_BASE
DIN6_F
Data
NC
GND
+5V
CLK
NC
CN7
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Hol e_6V_4
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Hol e_6V_1
CON20
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
DKMMX_ CON2
4
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Hol e_6V_2
CON20
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
MMX
Revision1.0
PS2-KEYBOARD
Hole Array
DKMMX_ CON3
VCC1_6V +6V VCC1_6V +6V VCC1_6V +6V
Hol e_6V_3
CON20
DKMMX_ CON1
P13/ADC 3
1
P12/ADC 2
2
M CU_SPI_CLK
3
GND
4
P37/SCL
5
P36/SDA
6
GND
7
PB0
8
PB1
9
PA0
10
PA1
11
PA2
12
PA3
13
PA4
14
PA5
15
PA6
16
PA7
17
PB2
18
GND
19
+9V
20
GND VCC1_6V +6V
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Hol e_GND2
VCC2_5V
Hol e_GND1
PB3
PD1
PD2
PC2/VSTBY
PC3/TSTAT
PC4/TERR#
P32/INT0
RESET#
GND
P10/ADC0
GND
P11/T2X
GND
P14/ADC4
GND
P15/ADC5
GND
P16/ADC6
GND
+9V
3
A
B
C
D
Getting Started With DK3400
Turbo Plus uPSD DK3400 Development Kit
Appendix B DK3400 Motherboard Schematic
Turbo Plus uPSD DK3400 Development Kit
6
Revision History
Revision History
Date
Revision
01-Mar-2005
1
Changes
First Release
UM0131
31/32
Turbo Plus uPSD DK3400 Development Kit
Revision History
If you have any questions or suggestions concerning the matters raised in this document,
please send them to the following electronic mail addresses:
[email protected] (for general enquiries)
Please remember to include your name, company, location, telephone number and fax number.
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for
any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of
STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously
supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of
STMicroelectronics.
The ST logo is a registered trademark of STMicroelectronics.
All other names are the property of their respective owners
© 2005 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia – Belgium - Brazil - Canada - China – Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco - Singapore
- Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
32/32
UM0131
">