advertisement
Hookup Diagrams
Microphones press HI-Z button press HI-Z button
Adjust
Vocal
Compression
Front Panel
Power Amp Mode switch set to
Stereo Main
Rear Panel
Keyboards
Portable Recorder
SRM450v2 Powered Stage Monitors
(plays mon 1 output)
C300z Passive Speakers
(plays stereo main mix)
HD1801 Powered Subwoofers
(plays main mix below 100 Hz)
6
This diagram shows microphones attached to channels 1 and 2, electric guitars connected directly to channels 5 and 6 (with hi-z switch pressed in), and a keyboard attached to channel 7's stereo inputs. A portable recorder is attached to the stereo tape outputs to record the performance.
Mackie SRM450v2 powered speakers are connected to the monitor 1 send, and are set up as stage monitors. The mon 1 controls of each channel allow you to create a stage monitor mix that is independent of the main mix. Use the monitor 1 graphic EQ to adjust the stage monitor EQ as desired.
C300z passive speakers are connected to the speaker-level power output of the powered mixer, and they play the main stereo mix to your audience. HD1801 powered subwoofers are connected to the main mix sub out, to reinforce the low end in your system.
Small Club System
PPM608
Microphones
Acoustic Guitar and Mic
Front Panel
Power Amp Mode switch set to
Mains/Mon 1
Rear Panel
Adjust
Vocal
Compression press HI-Z button
Drum
Machine
Power
Amplifier dual-mono mode
C200 Passive Stage Monitors
(plays mon 1 output)
Keyboards
SRM150 Powered Monitor
(plays mon 1 output)
Passive Subwoofers
(plays main mix below 100 Hz)
C300z Passive Speakers
House System
(plays mono main mix)
This diagram shows microphones attached to the mic inputs of channels 1 to 4, an electric guitar connected directly to channel 5 (with hi-z switch pressed in), an acoustic guitar microphone connected to channel 6 mic in, a keyboard attached to channel 7's stereo inputs, and a drum machine to channel 8.
A Mackie SRM150 powered monitor is connected to the monitor 1 send, and acts as a personal stage monitor to the keyboard player. The mon 1 knobs of each channel allow you to set up a monitor mix that is independent of the main mix. Use the monitor 1 graphic EQ to adjust the stage monitor EQ as desired.
The power amp mode switch is set to play the mono main mix on ch. A, and monitor 1 mix on ch. B.
Mackie C300z passive speakers are connected to the channel A speaker-level power output of the powered mixer, and they play the main mono mix to your audience.
C200 passive stage monitors are connected to the channel B speaker-level power output of the powered mixer. These play the stage monitor mix 1 to your performers.
Passive subwoofers are powered by a power amplifier connected to the main mix sub out, to reinforce the low end in your main mix.
House of Worship System
Owner’s Manual
7
Microphones
Front Panel
Rear Panel
Graphic EQ iPod
TM
Docking Station
L
MAIN OUT
R
~100-240 VAC 50-60Hz 20W
LINE
MIC
L
LIVE
RECORD
R
L
BOOTH
L
FX
SEND
R
PGM 2
PHONO
L
CD
L
PGM 1
L
PHONO CD
L
RETURN
L(MONO) R
R
LINE
PHONO
GND
R R
LINE
PHONO
GND
R
R
MIC dual-mono mode
Turntables with phono-level output
This diagram shows a wireless microphone receiver connected to the channel 1 line input, a graphic
EQ connected to channel 1's insert jack (to help control feedback in the wireless mic), a microphone connected to channel 2, and an iPod docking station attached to channel 8's RCA inputs.
A Mackie d.2 Pro is connected to two turntables, and its RCA output connects to the powered mixer's channel 7 stereo RCA inputs. Use the d.2 Pro's advanced DJ controls to get the best performance from your records. Use the powered mixer to play the d.2 Pro output, and control the mics and iPod.
The power amp mode switch is set to play the stereo main mix in the Mackie C300z passive speakers, connected to the speaker-level power outputs.
Passive subwoofers are powered by an amplifier connected to the main mix sub out to reinforce the low end in the main mix.
DJ System
8
PPM608
Microphones
Front Panel
Power Amp Mode switch set to
Mon 1/Mon 2
Rear Panel press HI-Z buttons
Adjust
Vocal
Compression
Keyboards
Send
Guitar Processor
(connected to INSERT)
Return
Electronic Drum Kit
HD1531
Powered
Speaker
HD1531
Powered
Speaker
C200 Passive Stage Monitors
(plays mon 2 output)
HD1801
Powered Subwoofer
(plays right main mix)
HD1801
Powered Subwoofer
(plays left main mix)
C300z Passive Stage Monitors
(plays mon 1 output)
This diagram shows microphones attached to the mic inputs of channels 1 to 4, electric guitars connected directly to ch. 5 and 6 (with hi-z switch pressed in), a guitar processor connected to ch. 6 insert, a keyboard attached to channel 7's stereo inputs, and an electronic drum kit attached to channel 8. Add vocal compression as required, by tweaking the compression knobs on channels 1 to 4.
The power amp mode switch is set to play the monitor 1 mix on channel A, and monitor 2 mix on channel B. Note: Press in the front panel FX send/mon 2 send switch, or monitor 2 will not play.
C200 passive stage monitors are connected to the channel B speaker-level power output of the powered mixer. These play the stage monitor mix 2 to your performers. C300z passive stage monitors are connected to the channel A speaker-level power output, and play stage monitor mix 1.
Mackie HD1531 powered speakers and HD1801 powered subwoofers are connected to the line-level main mix outputs, and play the stereo main mix to the audience.
Large Band System
Owner’s Manual
9
advertisement
Related manuals
advertisement
Table of contents
- 2 IMPORTANT SAFETY INSTRUCTIONS
- 3 READ THIS PAGE!
- 4 INTRODUCTION
- 6 HOOKUP DIAGRAMS
- 10 REAR PANEL FEATURES
- 10 1. POWER CONNECTION
- 10 2. POWER SWITCH
- 10 3. SPEAKER-LEVEL OUTPUTS
- 11 4. POWER AMP MODE SWITCH
- 11 5. VENTILATION AND REAR PANEL
- 11 6. HANDLES
- 12 FRONT PANEL FEATURES
- 12 7. MIC INPUTS
- 13 8. MONO LINE INPUTS (CH. 1 TO 4)
- 13 9. LINE/INSTRUMENT INPUTS (CH. 5, 6)
- 13 10. STEREO LINE INPUTS (CH. 7 AND 8)
- 13 11. RCA INPUTS (CH. 7 AND 8)
- 13 12. INSERT (CH. 1 TO 6)
- 13 13. TAPE OUTPUTS
- 13 14. BREAK SWITCH AND LED
- 14 15. FX/MON 2 SEND OUTPUT
- 15 16. FX FOOTSWITCH
- 15 17. MON 1 SEND
- 15 18. MAIN SUB
- 15 19. MAIN OUTPUTS
- 15 20. POWER AMP INPUTS
- 17 21. MON
- 17 22. FX/MON
- 17 23. HIGH EQ
- 17 24. MID EQ
- 17 25. LOW EQ
- 18 26. OVERLOAD (OL) LED
- 18 27. CHANNEL LEVEL
- 18 28. GAIN SWITCH
- 19 29. COMPRESSOR
- 19 30. HI-Z SWITCH
- 20 31. POWER LED
- 20 32. MAIN MASTER GRAPHIC EQ
- 20 33. FX TO MAIN
- 20 34. MAIN LEVEL
- 21 35. 100 HZ RUMBLE REDUCTION SWITCH
- 21 36. MAIN MIX METERS
- 21 37. MONITOR 1 MASTER GRAPHIC EQ
- 21 38. FX TO MON
- 21 39. MONITOR 1 LEVEL
- 21 40. 100 HZ RUMBLE REDUCTION SWITCH
- 21 41. MONITOR 1 METER
- 22 42. PHANTOM SWITCH
- 22 43. PRECISION PASSIVE EQ
- 22 44. POWER AMP LIMITER LEDS
- 22 45. FX/MON 2 SEND MASTER
- 22 46. SIG/OL LED
- 23 47. FX SEND (POST)/MON 2 SEND (PRE)
- 23 48. PRESET DISPLAY
- 23 49. PRESET SELECTOR, TAP DELAY AND LED
- 23 50. INTERNAL FX MUTE
- 24 APPENDIX A: SERVICE INFORMATION
- 25 APPENDIX B: CONNECTIONS
- 27 APPENDIX C: TECHNICAL INFORMATION
- 30 APPENDIX D: TABLE OF EFFECTS PRESETS
- 31 PPM608 LIMITED WARRANTY