ASSEMBLY. Weider 9000 Bench, WEEMBE3922

CABLE DIAGRAMS

The cable diagrams below show the proper routing of the High Cable (31), the Butterfly Cable (32), and the Low

Cable (33). Use the diagram to make sure that the cables and the cable traps have been assembled correctly. If the cables have not been correctly routed, the weight bench will not function properly and damage may occur.

The numbers show the correct route for each cable. Make sure that the cable traps do not touch or bind the

cables.

4

2

5

Butterfly Cable (32)

4

2

1

3

1

3

High Cable (31)

4

2

5

Low Cable (33)

1

3

5

ASSEMBLY

Make Things Easier for Yourself

Everything in this manual is designed to ensure that the weight bench can be assembled successfully by anyone. However, it is important to realize that the versatile weight bench has many parts and that the assembly process will take time. Most people find that by setting aside plenty of time, assembly will go smoothly.

Before beginning assembly, carefully read the following information and instructions:

• Assembly requires two people.

• Place all parts in a cleared area and remove the packing materials. Do not dispose of the packing materials until assembly is completed.

• Tighten all parts as you assemble them, unless instructed to do otherwise.

• As you assemble the weight bench, make sure all parts are oriented as shown in the drawings.

• For help identifying small parts, use the PART

IDENTIFICATION CHART in the centre of this manual.

The following tools (not included) are required for assembly:

• Two adjustable spanners

• One rubber mallet

• One standard screwdriver

• One Phillips screwdriver

• Lubricant, such as grease or petroleum jelly, and soapy water.

Assembly will be more convenient if you have a socket set, a set of open-end or closed-end wrenches, or a set of ratchet spanners.

Rack Assembly

1.

Before beginning assembly, be sure that you have read and understand the information in the box above.

Press a 50mm Square Inner Cap (43) into the end of the Right Base (1).

Insert an M10 x 60mm Carriage Bolt (50) up through the bottom of the Right Base (1). Lay the

Base on the floor.

Repeat this step with the Left Base (2).

1

43

1

43

50

2

20 5

2.

Slide the Centre Upright (5) onto the M10 x

60mm Carriage Bolts (50) in the Right and Left

Bases (1, 2). Make sure that the Centre Upright

is turned so the indicated bracket is on the

side shown. Hand tighten two M10 Nylon

Locknuts (49) onto the Bolts. Do not tighten the

Nylon Locknuts yet.

2

Bracket

1

5

49

49

50

2

3.

Attach the Foot Plate (9) and the Rear Upright (6) to the Right and Left Bases (1, 2) with two M10 x

68mm Bolts (46) and two M10 Nylon Locknuts

(49).

Attach the Foot Plate (9) to the Centre Upright (5) with an M10 x 68mm Bolt (46), an M10 Washer

(52), and an M10 Nylon Locknut (49).

Do not tighten the M10 Nylon Locknuts (49) yet.

3

46

46

5

1

9

52

49

49

2

6

6

100

110

120

130

140

150

WEIGHT

(lbs.)

10

20

30

40

50

60

70

80

90

Note: 1 lb. = .454 kg

WEIGHT RESISTANCE CHART

This chart shows the approximate weight resistance at each weight station. The column labeled “WEIGHT” refers to the amount of weight, in pounds, placed on the weight carriage. The weight resistance shown for the butterfly arm station is for each butterfly arm. Note: The actual resistance at each station may vary due to

friction between the cables, pulleys, and weight carriage.

BUTTERFLY ARM

(lbs.)

9

13

17

20

24

28

31

35

38

42

46

49

53

57

61

LOW PULLEY

(lbs.)

21

32

44

55

67

78

90

101

113

120

132

142

154

164

176

HIGH PULLEY

(lbs.)

21

32

44

55

67

78

90

101

113

120

132

142

154

164

176

19

USING THE CURL PAD

Remove the 50mm Square Inner Cap (43) from the

Front Leg (64).

Align a hole in the Curl Post (83) with the hole in the

Front Leg (64). Secure the Curl Post with the Curl

Knob (4). Be sure the Knob is fully tightened.

Note: When not using the Curl Pad (84), store it away from the weight bench.

84

83

43

4

64

ADJUSTING THE BACKREST

The Bench Backrest (69) can be used in a decline position, a level position, or either of two incline positions. To adjust the Backrest to the decline position, remove the Bench Pin (74) and insert it through the top set of holes in the Backrest Frames (67, 68) and the Bench Frame (63).

To adjust the Bench Backrest (69) to the level position, insert the Bench Pin (74) through the second set of holes from the top of the Backrest Frames (67, 68) and the Bench Frame (63).

To adjust the Bench Backrest (69) to an incline position, insert the Bench Pin (74) through one of the lower two sets of holes in the Backrest Frames (67,

68) and the Bench Frame (63).

WARNING:

When adjusting the position of the Bench Backrest (69), make sure that the Bench Pin (74) is fully inserted through both Backrest Frames (67, 68) and the hole in the Bench Frame (63).

69

67 68

74

63

18

4.

Attach one of the Uprights (3) to the Right Base

(1) with four M10 x 68mm Bolts (46), two Support

Plates (14), and four M10 Nylon Locknuts (49).

Do not tighten the Nylon Locknuts yet.

Repeat this step with the other Upright (not shown) and the Left Base (not shown).

4

3

49

49

14

14

1

46

5.

Press a 50mm Square Inner Cap (43) into the top of the right Upright (3).

Slide a Safety Spotter (15) onto the right Upright

(3) and engage the Knob (17) into the lowest adjustment hole in the Upright. Turn the Knob clockwise until it is tight.

Slide a Weight Rest (16) onto the right Upright (3) and engage the Knob (17) into an adjustment hole in the Upright. Turn the Knob clockwise until it is tight.

Repeat this step with the left Upright (not shown).

6.

Attach the Crossbar (7), with the decal on the side shown, to the right Upright (3) with four M10 x 68mm Bolts (46), two Support Plates (14), and four M10 Nylon Locknuts (49). Do not tighten

the Nylon Locknuts yet.

Attach the Crossbar (7) to the left Upright (not shown) in the same manner.

5

6

16

15

43

3

17

Adjustment

Holes

46

14

7

49 14

3

Decal

7

7.

Slide the Carriage Stop (19) onto the Rear

Upright (6). Make sure that the Carriage Stop is

oriented so the Carriage Stop Bushing (20) and the indicated hole are in the positions

shown. Attach the Carriage Stop to the hole near the bottom of the Rear Upright with an M8 x

70mm Bolt (58) and an M8 Nylon Locknut (48).

Press two 25mm Round Inner Caps (45) into the tube on the Weight Carriage (10). Insert an M10 x

19mm Bolt (61) into the bracket on the Weight

Carriage. Slide the Weight Carriage onto the Rear

Upright (6). Be sure the bracket is on the side

shown.

7

8.

Press three 50mm Square Inner Caps (43) into the indicated ends of the Top Frame (8).

8

45

10

61

48

20

19

Hole

6

58

45

43

8

43

43

9.

Attach the Top Frame (8) to the Crossbar (7) with two M10 x 68mm Bolts (46), two M10 Washers

(52), and two M10 Nylon Locknuts (49).

Attach the Top Frame (8) to the Centre Upright

(5) with two M10 x 68mm Bolts (46), two M10

Washers (52) and two M10 Nylon Locknuts (49).

Do not tighten the M10 Nylon Locknuts (49) yet.

9

10. Attach the Top Frame (8) to the Rear Upright (6) with three M10 x 68mm Bolts (46), two Support

Plates (14), and three M10 Nylon Locknuts (49).

Tighten the M10 Nylon Locknuts (49) used in steps 2–10.

10

52

46

46

52

49

8

7

49

49

5

14

8

49

14

46

6

8

ATTACHING THE LAT BAR TO THE HIGH PULLEY

STATION OR THE LOW PULLEY STATION

To use the high or low pulley station, attach the Lat

Bar (73) to the High Cable (31) or the Low Cable (not shown) using a Cable Clip (30). The Row Bar (not shown) can be attached in the same manner.

WARNING:

Always remove the Lat

Bar (73) when performing an exercise that does not require the use of the Lat Bar.

ATTACHING WEIGHTS TO THE WEIGHT CARRIAGE

To use the Weight Carriage (10), slide the desired amount of weight (not included) onto each side of the weight tube on the Weight Carriage. Secure the weight with the two Weight Pins (37).

WARNING:

Do not place more than

68 kg (150 lbs.) on the Weight Carriage (10).

Always place the same amount of weight on each side of the Weight Carriage.

To use Olympic weights, press two Adapter Bushings

(44) into the ends of each Weight Adapter (23). Slide a Weight Adapter onto each side of the weight tube on the Weight Carriage (10).

STORING WEIGHTS

To store weights, slide them onto the Storage Tubes

(22) on the Right and Left Bases (1, 2).

22

1

31

73

30

10

37

23

Weight

Tube

22

2

ATTACHING WEIGHTS TO THE LEG LEVER

To use the Leg Lever (66), slide the desired amount of weight (not included) onto the Weight Tube (65) and secure it with the Weight Pin (37).

To use Olympic weights, slide the Weight Adapter

(23) onto the Weight Tube (65).

WARNING:

Do not place more than

68 kg (150 lbs.) on the Weight Tube (65).

17

66

23

37

65

37. Attach the Curl Pad (84) to the Curl Post (83) with two M6 x 16mm Bolts (80).

37

84

83

80

38. Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in ADJUSTMENTS, below.

ADJUSTMENTS

This section explains how to adjust the weight bench. See the EXERCISE GUIDELINES on page 22 for important information about how to get the most benefit from your exercise program. Also, refer to the accompanying exercise guide to see the correct form for each exercise.

Make sure all parts are properly tightened each time you use the weight bench. Replace any worn parts immediately. The weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.

ADJUSTING THE WEIGHT RESTS AND SAFETY

SPOTTERS

Before beginning an exercise, move the Weight Rests

(16) and the Safety Spotters (15) to sets of holes in the Uprights (3) that are best suited for that exercise.

Turn the Knob (17) counterclockwise, and pull it out as far as it will go. Slide the Weight Rest or Safety

Spotter to the desired height. Engage the Knob into an adjustment hole in the Upright. Turn the Knob clockwise until it is tight.

The selected holes for the Safety Spotters (15) should represent the lowest point to which you want the barbell to go during the exercise. The selected holes for the Weight Rests (16) should be at a comfortable height for lifting and replacing the barbell.

15

16

3

17

Adjustment holes

17

16

3

WARNING:

Always set both Weight

Rests (16) and both Safety Spotters (15) at the same height.

15

16

11. Identify the Right and Left Butterfly Arms (11, 12) by noting the positions of the welded brackets.

Press two 45mm Square Inner Caps (42) into the ends of the Left Butterfly Arm (12). Wet the bottom end of the Butterfly Arm with soapy water.

Slide a Large Foam Pad (18) onto the end of the

Butterfly Arm.

Lubricate the axles on the Top Frame (8) with grease. Orient the Left Butterfly Arm (12) as shown and slide it onto the left axle so that it is behind the bracket on the Top Frame. Have a second person secure the Butterfly Arm with two

1” Retainers (35) and a 1” Cover Cap (36). Note:

Place the Retainers on top of the included retainer tool, as shown in the inset drawing.

Make sure the teeth on the Retainers bend toward the tool. Gently tap the tool onto the axle. Remove the tool, and tap the Cover Cap onto the axle.

Repeat this step with the Right Butterfly Arm

(11).

11

Axle

35

Retainer

Tool

11

Bracket

8

42

35

36

42

18

Lubricate

Axle

Welded

Bracket

12

12. Press a 25mm Round Inner Cap (45) into the upper end of a Storage Tube (22), as shown.

Attach the Storage Tube (22) inside the hole in the Right Base (1) with an M8 x 65mm Bolt (51), two M8 Washers (53), two 13mm x 12mm

Spacers (38), and an M8 Nylon Locknut (48).

Repeat this step with the other Storage Tube

(not shown) and the Left Base (2).

12

45

48

22

53

38

Hole

1

38

53

51

2

13. Identify the Butterfly Cable (32), which has an

eyelet on each end. Attach one end of the Cable to the bracket on the Left Butterfly Arm (12) with an M8 x 22mm Shoulder Bolt (60) and an M8

Nylon Locknut (48).

13

12

48

32

60

Bracket

9

14. Wrap the Butterfly Cable (32) around a “V”-Pulley

(25). Attach the Pulley and a Large Cable Trap

(27) to the bracket on the Centre Upright (5) with an M10 x 60mm Bolt (47) and an M10 Nylon

Locknut (49).

14

Bracket

49

27

25

47

32

5

15. Remove the 90mm Pulleys (24) from the preassembled Double “U”-Bracket (29).

Wrap the Butterfly Cable (32) under a 90mm

Pulley (24). Attach the Pulley to the Double “U”-

Bracket with an M10 x 45mm Bolt (57) and an

M10 Nylon Locknut (49).

15

32

49

24

29

57

16. Wrap the Butterfly Cable (32) around a “V”-Pulley

(25). Attach the Pulley and a Large Cable Trap

(27) to the bracket on the Centre Upright (5) with an M10 x 60mm Bolt (47) and an M10 Nylon

Locknut (49).

16

47

32

49

25

27

Bracket

5

17. Attach the Butterfly Cable (32) to the bracket on the Right Butterfly Arm (11) with an M8 x 22mm

Shoulder Bolt (60) and an M8 Nylon Locknut (48).

17

11

48

Bracket

60

32

10

33. Orient the Seat (70) with the wide end on the side shown. Attach the Seat to the Bench Frame (63) with four M6 x 16mm Bolts (80).

33

70

Wide

End

63

80

80

34. Press three 45mm Square Inner Caps (42) into the Leg Lever (66).

Attach the Weight Tube (65) to the Leg Lever (66) with an M8 x 58mm Bolt (41), two M8 Washers

(53), a 13mm x 10mm Spacer (75), and an M8

Nylon Locknut (48).

Press a 25mm Round Inner Cap (45) into the indicated end of the Weight Tube (65). Press the

25mm Round Angle Cap (76) onto the other end of the Weight Tube.

34

42

45

42

65

41

53

75

66

76

48

53

42

35. Lubricate the M10 x 68mm Bolt (46) with grease.

Attach the Leg Lever (66) to the Front Leg (64) with the Bolt and M10 Nylon Locknut (49).

36. Press the six 19mm Round Inner Caps (81) into the ends of the three Pad Tubes (71).

Slide a Pad Tube (71) into the hole in the Front

Leg (64). Slide two Foam Pads (72) onto the ends of the Pad Tube.

Slide the other two Pad Tubes (71) into the holes in the Leg Lever (66). Slide two Foam Pads (72) onto each Pad Tube.

35

49

66

36

72

72

72

81

71

81

71

81

81

66

46

Lubricate

64

64

72

72

72

15

Bench Assembly

29. Press two 51mm x 76mm Outer Caps (79) onto the Stabiliser (62). Attach the Stabiliser to the

Bench Frame (63) with two M10 x 60mm

Carriage Bolts (50) and two M10 Nylon Locknuts

(49).

29

63

79

49

62

50

30. Press three 50mm Square Inner Caps (43) into the Front Leg (64).

Attach the Front Leg (64) to the Bench Frame

(63) with two M10 x 65mm Bolts (54), two M10

Washers (52), and two M10 Nylon Locknuts (49).

30

43

54

52

43

49

43

64

49

63

79

31. Orient the Right and Left Backrest Frames (67,

68) as shown. Press six 25mm x 50mm Inner

Caps (82) into the Backrest Frames.

Orient the Bench Backrest (69) with the wide end on the side shown. Attach the Backrest to the

Backrest Frames (67, 68) with four M6 x 63mm

Bolts (56) and four M6 Washers (59). Do not

tighten the Bolts yet.

31

Wide

End

67

69

59

82

32. Lubricate the M10 x 180mm Bolt (78) with grease. Attach the Backrest Frames (67, 68) to the Bench Frame (63) with the Bolt, two M10

Washers (52), and an M10 Nylon Locknut (49).

Insert the Bench Pin (74) through a set of holes in the adjustment tubes on the Backrest Frames

(67, 68) and the indicated hole in the Bench

Frame (63).

Tighten the M6 x 63mm Bolts (56) used in step

31.

82

59

56

82

32

78

52

Lubricate

67

Adjustment

Tubes

68

59

56

56

52

49

74

68

63

Hole

14

18. Identify the High Cable (31), which is the

shorter of the two remaining cables. Route the eyelet end of the Cable up through the indicated hole in the Top Frame (8).

Wrap the High Cable (31) around a 90mm Pulley

(24). Attach the Pulley inside of the Top Frame (8) with an M10 x 65mm Bolt (54), two 15mm x

13mm Spacers (39), two M10 Washers (52), and an M10 Nylon Locknut (49).

18

49

52

24

39

52 8

31

39

54

19. Route the High Cable (31) down through the indicated hole in the Top Frame (8).

Wrap the High Cable (31) around a 90mm Pulley

(24). Attach the Pulley and a Cable Trap (26) inside of the Top Frame (8) with an M10 x 65mm

Bolt (54), a 15mm x 13mm Spacer (39), a 15mm x 10mm Spacer (40), two M10 Washers (52), and an M10 Nylon Locknut (49).

19

31

49

52

40

26

8

24

39

52

54

20. Remove the 90mm Pulleys (24) from the preassembled Pulley Plates (28).

Wrap the High Cable (31) under a 90mm Pulley

(24). Attach the Pulley and a Cable Trap (26) to the second hole from the top of the two Pulley

Plates (28) with an M10 x 45mm Bolt (57) and an

M10 Nylon Locknut (49).

20

21. Route the High Cable (31) up through the indicated hole in the Top Frame (8).

Wrap the High Cable (31) around a 90mm Pulley

(24). Attach the Pulley, a Cable Trap (26), a

15mm x 8mm Spacer (55), and a 15mm x 10mm

Spacer (40) to the Top Frame (8) with an M10 x

68mm Bolt (46), the two attached Support Plates

(14), and an M10 Nylon Locknut (49). Do not

overtighten the Bolt; the pulley must be able to pivot easily.

21

49

28

26

31

24

57

28

8

55

26

31

40

24

49

46

14

6

11

22. Attach the High Cable (31) to the M10 x 19mm

Bolt (not shown) in the bracket on the Weight

Carriage (10) with an M10 Nylon Locknut (49).

22

23. Locate the Low Cable (33). Route the eyelet end of the Cable through the hole in the Foot Plate (9) and through the Centre Upright (5).

Wrap the Low Cable (33) under a 90mm Pulley

(24). Attach the Pulley inside of the Centre

Upright (5) with an M10 x 65mm Bolt (54), two

M10 Washers (52), two 15mm x 13mm Spacers

(39), and an M10 Nylon Locknut (49).

23

33

9

5

49

52

39

52

24

39

54

31

49

Bracket

10

24. Wrap the Low Cable (33) around a 90mm Pulley

(24). Attach the Pulley to the bottom of the

Double “U”-Bracket (29) with an M10 x 45mm

Bolt (57) and an M10 Nylon Locknut (49).

24

49

29

24

57

33

25. Wrap the Low Cable (33) under a 90mm Pulley

(24). Attach the Pulley to the bracket on the Rear

Upright (6) with an M10 x 45mm Bolt (57) and an

M10 Nylon Locknut (49).

25

33

6

49

24

Bracket

57

12

26. Wrap the Low Cable (33) around a 90mm Pulley

(24). Attach the Pulley and a Cable Trap (26) to the second hole from the bottom of the two Pulley

Plates (28) with an M10 x 45mm Bolt (57) and an

M10 Nylon Locknut (49).

26

49

26

28

24

33

57

27. Attach the end of the Low Cable (33) inside the hole in the Rear Upright (6) with an M10 x 65mm

Bolt (54), two M10 Washers (52) and an M10

Nylon Locknut (49).

27

49

33

6

52

54

28. Attach the Backrest (13) to the Centre Upright (5) with two M6 x 63mm Bolts (56) and two M6

Washers (59).

28

Before using the weight rack, pull each cable a few times to be sure that the cables move smoothly over the pulleys. If one of the cables does not move smoothly, find and correct the problem. IMPORTANT: If the cables are not

properly installed, they may be damaged when heavy weight is used. See the CABLE

DIAGRAMS on page 20 for proper cable routing. If there is any slack in the cables, they will need to be tightened; see TROU-

BLESHOOTING AND MAINTENANCE on page

21.

13

5

56

59

56

13

51mm x 76mm Outer Cap (79)

19mm Round Inner Cap (81)

25mm Round Inner Cap (45)

25mm x 50mm Inner Cap (82)

50mm Square Inner Cap (43)

15mm x 8mm Spacer (55)

13mm x 12mm Spacer (38)

13mm x 10mm Spacer (75)

15mm x 13mm Spacer (39)

45mm Square Inner Cap (42)

15mm x 10mm Spacer (40)

1” Retainer (35)

M10 x 180mm Bolt (78)

PART IDENTIFICATION CHART

Refer to the drawings below to identify small parts used in assembly. The number in parentheses by each drawing is the key number of the part, from the PART LIST in the centre of this manual. Note: Some small parts

may have been pre-attached. If a part is not in the parts bag, check to see if it has been pre-attached.

M8 Nylon Locknut (48)

M10 Nylon Locknut (49)

M6 Washer (59)

M10 Washer (52)

M8 Washer (53)

M6 x 16mm Bolt (80)

M10 x 19mm Bolt (61)

M8 x 22mm Shoulder Bolt (60)

M6 x 63mm Bolt (56)

M8 x 58mm Bolt (41)

M8 x 70mm Bolt (58)

M10 x 68mm Bolt (46)

M10 x 65mm Bolt (54)

M10 x 60mm Carriage Bolt (50)

M8 x 65mm Bolt (51)

M10 x 60mm Bolt (47)

M10 x 45mm Bolt (57)

PART LIST—Model No. WEEMBE39220

R0802A

Key No.

Qty.

29

30

31

32

25

26

27

28

21

22

23

24

17

18

19

20

13

14

15

16

9

10

11

12

7

8

5

6

3

4

1

2

37

38

39

40

33

34

35

36

41

42

43

44

1

1

1

2

2

2

2

4

10

2

3

9

1

1

4

2

1

10

2

2

1

1

1

1

1

1

1

1

2

1

1

1

5

2

3

4

4

2

1

2

1

7

10

6

Description

Right Base

Left Base

Upright

Curl Knob

Centre Upright

Rear Upright

Crossbar

Top Frame

Foot Plate

Weight Carriage

Right Butterfly Arm

Left Butterfly Arm

Backrest

Support Plate

Safety Spotter

Weight Rest

Knob

Large Foam Pad

Carriage Stop

Carriage Stop Bushing

Carriage Bushing

Storage Tube

Weight Adapter

90mm Pulley

“V”-Pulley

Cable Trap

Large Cable Trap

Pulley Plate

Double “U”-Bracket

Cable Clip

High Cable

Butterfly Cable

Low Cable

Butterfly Bushing

1” Retainer

1” Cover Cap

Weight Pin

13mm x 12mm Spacer

15mm x 13mm Spacer

15mm x 10mm Spacer

M8 x 58mm Bolt

45mm Square Inner Cap

50mm Square Inner Cap

Adapter Bushing

Key No. Qty. Description

73

74

75

76

69

70

71

72

65

66

67

68

61

62

63

64

57

58

59

60

53

54

55

56

49

50

51

52

45

46

47

48

81

82

83

84

77

78

79

80

85

#

#

#

1

1

1

1

3

6

1

1

1

1

1

1

1

1

1

1

6

2

5

1

1

6

6

6

47

4

2

17

5

28

2

6

1

1

6

6

2

6

4

1

1

1

1

1

25mm Round Inner Cap

M10 x 68mm Bolt

M10 x 60mm Bolt

M8 Nylon Locknut

M10 Nylon Locknut

M10 x 60mm Carriage Bolt

M8 x 65mm Bolt

M10 Washer

M8 Washer

M10 x 65mm Bolt

15mm x 8mm Spacer

M6 x 63mm Bolt

M10 x 45mm Bolt

M8 x 70mm Bolt

M6 Washer

M8 x 22mm Shoulder Bolt

M10 x 19mm Bolt

Stabiliser

Bench Frame

Front Leg

Weight Tube

Leg Lever

Right Backrest Frame

Left Backrest Frame

Bench Backrest

Seat

Pad Tube

Foam Pad

Lat Bar

Bench Pin

13mm x 10mm Spacer

25mm Round Angled Cap

Handgrip

M10 x 180mm Bolt

51mm x 76mm Outer Cap

M6 x 16mm Bolt

19mm Round Inner Cap

25mm x 50mm Inner Cap

Curl Post

Curl Pad

Row Bar

User’s Manual

Exercise Guide

Retainer Tool

Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover of the user’s manual for information about ordering replacement parts.

EXPLODED DRAWING—Model No. WEEMBE39220

R0802A

49

43

72

1

21

16

15

21

21

3

14

77

77

81

37

45

43

49

17

17

11

42

44

14

34

35

36

18

14

52

23

48

42

46

49

60

32

34

48

46

18

7

52

49

35

36

12

60

32

43

49

39

24

39

43

52

46

52

54

8

49

52

46

40

26

24

55

26

39

40

24

49

52

54

47

25

27

25

47

43

49

14

49 28

24

28

49

31

5

26

13

57

30

30 59

56

24

42

46

56

49

14

14

46

59

49

29

24

57

52

49

24

49

33

44 37

21

31

45

23

45

10

61

49

37

9

49

49 52

49

39

24

39

49

22

52

54

14

48

53

38

38

53

51

21

20

48

19

58

45

46

33

46

69

43

46

50

82

57

14

6

16

52

21

54

21

84

82

73

78

52

67

59

56

15

85

77

59

56

21

71

44

42

81

65

41

53

23 44

75

42

72

42

66

76

53

48

72

54

77

49

72

52

64

83

52

43

80

46

4

49

49

80

81

82

82

82

59

56

70

82

56

63

80

71

79

68

52

49

74

59

49

50

62

46

14

3

14

50

51

53

38

45

22

2

17

17

46

38

53

81

79

49

48

43

43

72

43