Specifications

Laboratory Grade, Triple Output, Dual Tracking

DC regulated power supply

DPD - 1850 / 3030 / 6015 (Linear mode)

Description

The DPD series are intended for engineers who need a wide range of voltage and current to cover their applications with ease.

Double the voltage or current can be obtained in series mode or parallel mode respectively with the two independent and fully isolated outputs by the mode selector switch .

The master unit controls the combined outputs with accurate tracking capability.

Constant Current, CC and Constant Voltage, CV with automatic cross over are effective in all three modes.

To offer maximum versatility for electronic engineer, the DPD series have a third separate 5A, 1.5~6V adjustable output for old and new logic circuits such as Fast & LS

TTL.

The current and voltage level of this third output can be read in the Master's LED meters.

The specifications of the line , load regulation and ripple and noise limits are comparable to if not better than the reputable make in the industry

Features

• Simultaneous digital metering of current and voltage.

• Twin 4 digit meters with large LED display.

• Selectable Switch for Normal and Series/ Parallel

Dual Tracking modes.

• Precise control of voltage & current settings by wire-wound potentiometers.

• Laboratory grade line and load regulation and low ripple and noise.

• Variable Current Limiting with auto cross- over and indication (CC, CV)

• Third Output (AUX. : 1-6.5V , 5A) with display & overload LED.

• Retractable Alloy Handles.

Typical Applications

• Product Design

• Bench Calibration and Repair

• Manufacturing Production Tests

• Training.

All values are based on the Standard ambient Temperature 25°C and Pressure 0.1Mpa.

* SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE *

Laboratory Grade, Triple Output, Dual Tracking


DPD - 1850 / 3030 / 6015 (Linear mode)

Specifications

Master / Slave Independent Output

Output Voltage Range

Load Voltage Regulation (0-100% Load)

Line Regulation (±10% Variation)

Ripple & Noise (RMS)

Output Current Range

Load Current Regulation

Line Current Regulation

Ripple Current

Recovery Time

Series Mode Output



Load Regulation

Tracking Error

Parallel Mode Output



Load Regulation

Tracking Error

Auxiliary Output


Rated Output Current

Load Voltage Regulation (0-100% Load)

Line Regulation (±10% Variation)

Ripple & Noise (RMS)

General

Selectable Input Voltage :

Meters & Displays :

Green LED :

Red LED :

Insulation :

Cooling System :

Protection :

EMC & Electrical Safety :

Dimension :

Weight :

DPD-1850 DPD-3030

0 - 18VDC

≤0.01% +3mV

≤0.01% +3mV

≤1mVrms

0 - 5ADC

≤0.2% +3mA

≤0.2% +3mA

≤3mA rms

≤100µ second

0 - 36VDC

0 - 5ADC

≤300mV

≤0.5% +10mV

0 - 18VDC

0 - 10ADC

≤300mV

≤0.5% +10mV

0 - 30VDC

0 - 3ADC

0 - 60VDC

0 - 3ADC

0 - 30VDC

0 - 6ADC

1.5 - 6VDC

5A (5A foldback limited)

≤10mV

≤5mV

≤1mVrms

DPD-6015

0 -60VDC

0 - 1.5ADC

0 - 120VDC

0 - 1.5ADC

0 - 60VDC

0 - 3ADC

*110VAC / 120VAC / 230VAC / 240VAC

*Frequency 50/60 Hz~

*C.C. & C.V. Indicators

*4-Digit LED Meters

*Voltmeter Accuracy ±0.5% +2 Counts

*Voltmeter Resolution 10mV

*Ammeter Accuracy ±0.5% +2 Counts

*Ammeter Resolution 1mA

*Master's Voltmeter & Ammeter switched to read Auxiliary output

*Auxiliary Output Overload indication

*Withstanding test (60 second 1mA) 1500V :

Power cord to housing

Power cord to output terminal

*Withstanding test (60 second 10mA) 500V :

Output terminal to housing

*Insulation Resistance at 500VDC :

Housing to power cord 30 mega Ohm

Housing to output terminal 30 mega Ohm

*Fan Cool

*Overload , Over Temperature , Short Current , Reverse Polarity ,

Input Socket with 8A Fuse

*Designed & Manufactured to meet CE Standard

*379 x 280 x 135mm / 14.9 x 11 x 5.3in.

*12Kgs / 26.4Lbs



36W Din-Rail

Switching Mode Power Supply

DRS - 3600-05 / 3600-12 / 3600-24

Description

This range of compact DIN mounted switching mode power supplies are designed for a wide range of control equipments which demands good quality regulated DC power source with excellent EMC immunity and electrical performance in an industrial environment.

Up to 5 units can be connected in parallel.


Voltage Range (Auto Select)

Frequency Range

Full Load AC Current

No Load AC Current

Inrush Current , cold start @25°C *

Leakage Current

Efficiency

OUTPUT

Nominal DC Voltage

Voltage Adjust Range

Rated Current

Rated Power

Ripple & Noise (peak to peak)**

Line Regulation

Load Regulation (10% - 100%)

Hold-up Time (Full Load)

Parallel Operation

PROTECTION

Over Load / Over Current

Over Output Voltage

SAFETY & EMC

Safety Standards

Withstand Voltage

Insulation Resistance

EMI Radiation & Conduction

Harmonics Current

EMC Immunity

ENVIRONMENT

Working Temperature

Derating above 50°C

Working Humidity

Storage Temperature Humidity

GENERAL

Switching Frequency @ Full Load

Case Material

Safety Class

Case Protection

Mounting

Connection

REMARK

DRS-3600-05

90 - 130Vac ; 180 - 260Vac

47 - 63Hz~

0.5A@100Vac ; 0.3A@230Vac

15mA@100Vac ; 30mA@230Vac

10A@100Vac ; 25A@230Vac

2mA

75%@100Vac ; 76%@230Vac

DRS-3600-12


82%@100Vac ; 83%@230Vac

5V

4.2 - 6V

7.2A

36W

≤50mV

≤0.2%

12V

10.5 - 14V

3A

≤0.8% ≤0.3%

>20mSec@100Vac ; >30mSec@230Vac

5 units max. user selectable

8 - 10A, C.C., Auto-restart

9 - 11Vdc

3.5 - 4.5A, C.C., Auto-restart

18 - 20Vdc

DRS-3600-24


85%@100Vac ; 86%@230Vac

24V

21.5 - 28V

1.5A

≤0.3%


30 - 35Vdc

EN60950

I/P - O/P 3KVac ; I/P - F/G 1.5KVac ; O/P - F/G 0.5KVac

I/P - O/P, I/P - F/G, O/P - F/G 100Mohm and 500Vdc

EN55022 Class B

EN61000-3-2, 3

EN61000-4-2, 3, 4, 5, 6, 8, 11, EN55024

EN60950 : -10°C to +60°C (UL508 : 0 to 40°C)

See Derating Curve

20 - 90 RH non-condensing

-10°C to +80°C , 20 - 90 RH non-condensing

65 - 85KHz

Electro-Galvanized steel & Aluminum Enclosure and Poly-carbonate Front Panel

Degree of Protection 1 (IEC 5360)

IP 20 (IEC 529)

Snap on type with self locking can be installed on 35 mm Din-Rails / 7.5 or 15

Screw terminals with double terminals for output

*Ta=25°C Cold start **100MHz Band width scope



60W Din-Rail


DRS - 6000-05 / 6000-12 / 6000-24 / 6000-48

Description




INPUT


Frequency Range


No Load AC Current


Leakage Current

Power Factor

Efficiency

OUTPUT

Nominal DC Voltage


Rated Current

Rated Power


Line Regulation



Parallel Operation

PROTECTION


Over Output Voltage

SAFETY & EMC

Safety Standards

Withstand Voltage



Harmonics Current

EMC Immunity

ENVIRONMENT

Working Temperature


Working Humidity


GENERAL


Case Material

Safety Class

Case Protection

Mounting

Connection

REMARK

DRS-6000-05 DRS-6000-12

90 - 130Vac ; 180 - 260Vac

47 - 63Hz~

1A@100Vac ;

0.5A@230Vac

15mA@100Vac ;

30mA@230Vac

15A@100Vac ; 30A@230Vac

2mA min. 60%

75%@100Vac ;

76%@230Vac

1.1A@100Vac ;

0.55A@230Vac

25mA@100Vac ;

30mA@230Vac

82%@100Vac ;

83%@230Vac

DRS-6000-24

1.1A@100Vac ;

0.55A@230Vac

25mA@100Vac ;

30mA@230Vac

85%@100Vac ;

86%@230Vac

5V

4.2 - 6V

10A

60W

≤50mV

12V

10.5 - 14V

5A

≤20mV

≤50mV



10 - 13A,

C.C., Auto-restart

9 - 11Vdc

6 - 7A,

C.C., Auto-restart

18 - 20Vdc

EN60950



EN55022 Class B

EN61000-3-2, 3

EN61000-4-2, 3, 4, 5, 6, 8, 11, EN55024

EN60950 : -10°C to +60°C (UL508 : 0 to 40°C)

See Derating Curve



24V

21.5 - 28V

2.5A

2.7 - 3.5A,

C.C., Auto-restart

30 - 35Vdc

65 - 85KHz



IP 20 (IEC 529)






DRS-6000-48

1.1A@100Vac ;

0.55A@230Vac

25mA@100Vac ;

30mA@230Vac

85%@100Vac ;

86%@230Vac

48V

44.5 - 52V

1.25A

1.5 - 2A,

C.C., Auto-restart

60 - 65Vdc

120W Din-Rail


DRS - 1210-12 / 1210-24 / 1210-48

Description




DRS-1210-12 DRS-1210-24 DRS-1210-48

INPUT


Frequency Range


No Load AC Current


Leakage Current

Power Factor

Efficiency

OUTPUT

Nominal DC Voltage


Rated Current

Rated Power


Line Regulation



Parallel Operation

PROTECTION


Over Output Voltage

SAFETY & EMC

Safety Standards

Withstand Voltage



Harmonics Current

EMC Immunity

ENVIRONMENT

Working Temperature


Working Humidity


GENERAL


Case Material

Safety Class

Case Protection

Mounting

Connection

REMARK

90 - 130Vac ; 180 - 260Vac

47 - 63Hz~

2.8A@100Vac ; 1.2A@230Vac 2.6A@100Vac ; 1A@230Vac 2.6A@100Vac ; 1A@230Vac

100mA@100Vac ; 140mA@230Vac 90mA@100Vac ; 120mA@230Vac 90mA@100Vac ; 120mA@230Vac

25A@100Vac ; 55A@230Vac

2mA min. 70%

82%@100Vac ; 83%@230Vac 85%@100Vac ; 86%@230Vac 86%@100Vac ; 87%@230Vac

12V

10.5 - 14V

10A

120W

24V

22.5 - 28V

5A

≤50mV

≤0.2%

≤0.3%




16.5 - 18.5Vdc


30 - 35Vdc

EN60950



EN55022 Class B

EN61000-3-2, 3

EN61000-4-2, 3, 4, 5, 6, 8, 11, EN55024

EN60950 : -10°C to +60°C (UL508 : 0 to 40°C)

See Derating Curve



48V

44.5 - 53V

2.5A


63 - 68Vdc

45 - 55KHz



IP 20 (IEC 529)






240W Din-Rail


DRS - 2410-12 / 2410-24 / 2410-48

Description




DRS-2410-12 DRS-2410-24 DRS-2410-48

INPUT


Frequency Range


No Load AC Current


Leakage Current

Power Factor

Efficiency

OUTPUT

Nominal DC Voltage


Rated Current

Rated Power


Line Regulation



Parallel Operation

PROTECTION


Over Output Voltage

SAFETY & EMC

Safety Standards

Withstand Voltage



Harmonics Current

EMC Immunity

ENVIRONMENT

Working Temperature


Working Humidity


GENERAL


Case Material

Safety Class

Case Protection

Mounting

Connection

REMARK

90 - 130Vac ; 180 - 260Vac

47 - 63Hz~

4.0A@100Vac ; 1.9A@230Vac 3.9A@100Vac ; 1.7A@230Vac 3.9A@100Vac ; 1.7A@230Vac

80mA@100Vac ; 140mA@230Vac 80mA@100Vac ; 140mA@230Vac 80mA@100Vac ; 140mA@230Vac

32A@100Vac ; 58A@230Vac

2mA min. 70%

84%@100Vac ; 85%@230Vac 88%@100Vac ; 88%@230Vac 88%@100Vac ; 88%@230Vac

12V

10 - 14V

20A

240W

24V

22.5 - 28V

10A

≤50mV

≤0.2%

≤0.5% ≤0.3%



21 - 21.8A, C.C., Auto-restart

16.5 - 18.5Vdc


30 - 35Vdc

EN60950



EN55022 Class B

EN61000-3-2, 3

EN61000-4-2, 3, 4, 5, 6, 8, 11, EN55024

EN60950 : -10°C to +60°C (UL508 : 0 to 40°C)

See Derating Curve



48V

44 - 53V

5A

≤0.3%


63 - 68Vdc

45 - 55KHz



IP 20 (IEC 529)






Single Output


EP - 601 / 611

(Linear mode)

Description

This series of low power , wide output voltage range DC regulated power supplies with adjustment controls for output voltage and current are suitable for college, general use , service field and hobbyist.

Features

• 0 - 30V adjustable output control

• 0 - 2.5A adjustable output control

• Precision ammeter and voltmeter

• Current limiting with LED indicator

• High stability

• One screw-on output plus two snap-on terminals

• Overload and short circuit protection

• Galvanized steel case


Output Voltage

Rated Output Current

Ripple & Noise (r.m.s.)

Load Regulation

Line Regulation

Input Voltage

Meter Type

V Meter Range

A Meter Range

Meters' Accuracy

Cooling System

Protection Devices

Approvals

Dimensions (WxHxD)

Weight

Accessory

EP - 601

0 - 30VDC

2.5A

<5mV

<0.05% +10mV

EP - 611

<0.05% +10mV

230VAC / 50Hz~ (120VAC / 60Hz~ or on request)

Analog Meter

0 - 35V

0 - 3A

7% fsd

Natural Convection

LCD Meter

3 digit display

3 digit display

1% +2 counts

Overload , Short Circuit

CE EN 60065 , EN 55014

150 x 145 x 200mm / 5.9 x 5.7 x 7.9in.

2.8Kgs / 6.2Lbs

User Manual



Description

The EP - 603/613 series are designed for general electronic servicing, school electronics, laboratory and hobbyist. All units may be used as either a constant voltage supply with current limiting or as constant current source with voltage limiting. Three independent outputs, two are fixed voltage, and one adjustable voltage.

Triple Output


EP - 603 / 613

(Linear mode)

Features

• One 0 - 30V adjustable output

• One 5V 500mA snap-on output


• Current limiting with Indicator

• Adjustable current control



• Poly-carbonate front panel


Output Voltage


Fixed Output Voltage 1



Load Regulation

Line Regulation

Input Voltage

Meter Type

V Meter Range

A Meter Range


Output Terminals

Cooling System


Approvals


Weight

Accessory

EP - 603

0 - 30VDC

EP - 613

2.5A

5VDC 0.5A Continuous / 1A Maximum


<5mV

<0.05% +10mV

<0.05% +10mV


Analog Meter

0 - 30V

0 - 3A

LCD Meter

3 digit display

3 digit display

7% fsd 1% +2 counts

One variable main output screw-on type , two snap on fixed voltage 1 and 2

Natural Convection


CE EN 60065 , EN 55014

150 x 145 x 200mm / 5.9 x 5.7 x 7.9in.

2.8Kgs / 6.2Lbs

User Manual



Fixed Output


EP - 806 / 815 / 820 / 825

(Linear mode)

Description

T

his series of cost effective fixed output voltage DC 13.8V regulated power supplies provide clean and stable DC power source for transceiver and the Amateur Radio field. The two low current snap on terminals offer more flexibility.

Features

• Fixed 13.8V DC output

• High stability

• Low ripple and noise

• One screw-on output terminal

• Two snap on output (3A) terminals

• Overload warning LED indicator





Output Voltage


EP - 806

13.8VDC

6A

Peak Output Current

7A


10mV

Load Regulation

Line Regulation

40mV

15mV

Input Voltage

Cooling System

Natural

Convection

EP - 815

12A

15A

60mV

Thermostatic

Control Fan

EP - 820

18A

20A

80mV


Thermostatic

Control Fan

EP - 825

25A

30A

100mV

Thermostatic

Control Fan


Approvals

Size (WxHxD)mm

(WxHxD)inch

Weight

Accessory


CE EN 60065 , EN 55014

150x145x200

5.9x5.7x7.9

4Kgs / 8.8Lbs

User Manual

150x145x300

5.9x5.7x11.8

150x145x300

5.9x5.7x11.8

150x145x300

5.9x5.7x11.8

5.2Kgs / 11.4Lbs 6.5Kgs /14.3Lbs 9Kgs / 19.8Lbs



Description

T

his series of low ripple and noise, adjustable voltage power supplies are designed for telecommunication field, workshop, production line and college. The special designed trifler wound transformer with thermal fuse and the extensive overload protection by dissipation limiting circuitry for the pass transistors make this series proven and well known for its reliability and stability.

Single Output


EP - 907 / 912 / 920 / 925

(Linear mode)

Features

• 3 - 15V DC adjustable output

• Fixed voltage mode at 13.8V DC



• High stability


• One screw on and 2 snap on terminals


• Fan cooling system for models over 200VA

• Output current limit is depended on output voltage

30

20

10

0

The current of the unit is depended on the output voltage as the following curve.

2 4 6 8 10 12 14 15

Output Voltage ( V )

EP - 925

EP - 920

EP - 912

EP - 907


EP - 907

Variable Output Voltage

3 - 15VDC

Fixed Output Voltage

13.8VDC


6A

EP - 912 EP - 920 EP - 925


7A


10mV

Load Regulation

Line Regulation

40mV

15mV

Input Voltage

V Meter Range

A Meter Range


Cooling System

0 - 20V

0 - 10A

7% fsd

Natural

Convection

12A

15A

60mV

0 - 15A

Thermostatic

Control Fan


18A

20A

80mV


0 - 20A

Thermostatic

Control Fan

25A

30A

100mV

0 - 30A

Thermostatic

Control Fan


Approvals

Size (WxHxD) mm

(WxHxD) inch

Weight

Accessory

CE EN 60065 , EN 55014

150x145x200

5.9x5.7x7.9

150x145x300

5.9x5.7x11.8

150x145x300

5.9x5.7x11.8

150x145x300

5.9x5.7x11.8

4.5Kgs / 9.9Lbs

5.5Kgs / 12Lbs 7Kgs / 15.4Lbs

9Kgs / 19.8Lbs

User Manual



Single Output


EPA - 9300 / EPD - 9300

(Linear mode)

Description

These high current power supplies are made for continuous operation and ideal to replace car batteries in situations such as : servicing or demonstrating high power car audio, ham radios, telecommunication equipment. The innovative design of the output terminals and the concealed voltage control knob are made for the above applications.

The main high current output is at the back of unit, ideal for continuous operation. The voltage control knob is protected from in-adverdent tempering behind the two position flip cover at the front panel.

Features

• 1 - 15VDC adjustable output control

• 28A output current at >13.5VDC

• 13.8V DC output center lock

• High RFI stability

• Temperature control variable speed cooling fan

• Overload warning LED


• One 28A screw on terminal at back panel

• Two 3A snap on terminal on front panel for easy access

• Voltage control protected by flip cover

30


EPA-9300

EPD-9300

20

10

0

2 4 6 8 10 12 14 15



EPA - 9300

1 - 15VDC

28A

33A

5mV

50mV

5mV


Analog Meter

0 - 20V

0 - 35A

7% fsd

LCD Meter

3 digit display

3 digit display

1% +2 counts

Temperature control variable speed cooling fan


CE EN 60065 , EN 55014

250 x 140 x 225mm / 9.8 x 5.5 x 8.9in.

9.5Kgs / 21Lbs

User Manual

EPD - 9300

Output Voltage




Load Regulation

Line Regulation

Input Voltage

Meter Type

V Meter Range

A Meter Range


Cooling System


Approvals


Weight

Accessory



Fixed Output


LP - 502 / 503 / 504 / 512 / 513 / 514

(Linear mode)

Features Description

The LP - 500 series is a low power, DC regulated power supplies designed for 13.8V DC equipment, such as transceiver, automotive and marine electronic equipment. Advanced designs make this series achieve good performance, high stability, good reliability and cost effective.


• High stability


• Compact size





Output Voltage




Load Regulation

Line Regulation

Input Voltage

Cigarette Socket

Cooling System


Approvals


Weight

LP-502 LP-512 LP-503 LP-513 LP-504 LP-514

13.8VDC

2A 2A 3A 3A 4A 4A

4A

4mV

4A

4mV

5A

5mV

5A

5mV

6A

6mV

6A

6mV

120mV 120mV 125mV 125mV 130mV 130mV

250mV 250mV 280mV 280mV 320mV 320mV


NO YES NO YES NO

Natural Convection


CE EN 60065 , EN 55014

160x92x150mm

6.3x3.6x5.9inch

2.4Kgs / 5.3Lbs

160x92x165mm

6.3x3.6x6.5inch

2.7Kgs / 6Lbs

YES

160x92x165mm

6.3x3.6x6.5inch

3Kgs / 6.6Lbs



Master Slave

Laboratory

Grade


MPA - 1850/3030/6015 , MPD - 1850/3030/6015

(Linear mode)

Description Features

This series LABORATORY GRADE DC

POWER SUPPLIES are built with precision coarse and fine output voltage and current limiting controls. The OVP ( output over voltage protection ) protects voltage sensitive load by instant shutting down the supply when output voltage is in excessive to the set voltage due to line surge or otherwise. Current limiting control with automatic cross over of constant voltage

(CV) and constant current (CC) mode makes this series ideal for R&D work in laboratory situations.

• Master / Slave connection with tracking operation

• Auto-cross over CV and CC

• LED indicators for CV and CC


• Excellent load and line regulation

• Coarse and fine voltage / current controls


• Floating ground output


Output Voltage

Output Voltage Control


Output Current Control


Load Regulation

Line Regulation

Input Voltage

Meter Type

V Meter Range

A Meter Range


Cooling System

LED Indicators

Approvals


Weight

Remark

MPA-1850 MPD-1850 MPA-3030 MPD-3030 MPA-6015 MPD-6015

0 - 18VDC 0 - 18VDC

Fine and Coarse adjust

0 - 5A 0 - 5A

Fine and Coarse adjust

0 - 30VDC 0 - 30VDC

0 - 3A 0 - 3A

1mV

0.02% +3mV

0.02% +3mV


0 - 60VDC 0 - 60VDC

0 - 1.5A

0 - 1.5A

Analog

0 - 20V

0 -5A

7% fsd

LED

3digit

Analog

0 - 35V display 0 - 3A

1% +2count 7% fsd

Natural Convection

C.C. and C.V.

CE IEC 1010 , EN 55011

205x115x270mm ( 8x4.5x10.8in. )

LED

3digit display

1% +2count

Analog

0 - 70V

1.5A

7% fsd

LED

3digit display

1% +2count

5Kgs / 11Lbs

Master / Slave connections with tracking CV and CC mode auto cross over



Description

The NP - 9600 series are designed for general electronic servicing, school electronics, laboratory and hobbyist. All units may be used as either a constant voltage supply with current limiting.

Three independent outputs, two are fixed voltage, and one adjustable voltage.

Triple Output


NP - 9603 / 9613 / 9605 / 9615

(Linear mode)

Features









• Housing are available in (Pantone warm grey 1C or Pantone 433C dark grey)


Output Voltage





Load Regulation

Line Regulation

Input Voltage

Meter Type

V Meter Range

A Meter Range



Cooling System


Approvals


Weight

NP - 9603

0 - 30VDC

NP - 9613 NP - 9605

3A 3A


5A


5mV

20mV 20mV 30mV

10mV


Analog

0 - 30V

0 - 3A

LCD

3 digit display

3 digit display

7% fsd 1% +2 count 7% fsd


Natural Natural

Convection Convection


Thermostatic

Control Fan

CE EN 61558 , EN 55014

Analog

0 - 30V

0 - 5A

205x115x230mm

8x4.5x9in.

5Kgs/11Lbs

205x115x230mm

8x4.5x9in.

5Kgs/11Lbs

NP - 9615

5A

30mV

LCD

3 digit display

3 digit display

1% +2 count

Thermostatic

Control Fan

205x115x280mm 205x115x280mm

8x4.5x11in.

8x4.5x11in.

6.5Kgs/14.3Lbs

6.5Kgs/14.3Lbs



Triple Output


NP - 9625

(Linear mode)

Description

NP - 9625 are designed for general electronic servicing, school electronics, laboratory and hobbyist. All units may be used as either a constant voltage supply with current limiting.

Three independent outputs, two are fixed voltage, and one adjustable voltage.

Features









• Housing are available in (Pantone warm grey

1C or Pantone 433C dark grey)


Output Voltage





Load Regulation

Line Regulation

Input Voltage

Meter Type

V Meter Range

A Meter Range



Cooling System


Approvals


Weight

NP - 9625

0 - 30VDC

10A



5mV

≤50mV

≤10mV


LCD Meter

3 digit display

3 digit display

Volt meter : +/-1% +1 count , Ammeter : =/-1% +3 count


Thermostatic Control Fan


CE EN 61010 , EN 55011

205 x 125 x 280mm / 8 x 4.5 x 11in.

6.5Kgs / 14.3Lbs



Description

This series of cost effective fixed output voltage DC 13.8V regulated power supplies provide clean and stable DC power source for transceiver and the Amateur Radio field. The two low current snap on terminals offer more flexibility.

Fixed Output


NP - 9812 / 9818 / 9825

(Linear mode)

Features


• High stability


• One screw-on output terminal

• Thermostatic Variable speed cooling fan

• Two snap on output (3A) terminals





• Housing are available in (Pantone warm grey

1C or Pantone 433C dark grey)


Output Voltage




Load Regulation

Line Regulation

Input Voltage

Cooling System


Approvals


Weight

NP - 9812

13.8VDC

12A

15A

5mV

NP - 9818

18A

20A

NP - 9825

25A

30A

30mV

5mV

40mV 50mV


Variable speed thermally control fan


CE EN 61558 , EN 55014

205x115x280mm / 8x4.5x11in.

5.2Kgs/11.4Lbs

6.5Kgs/14.3Lbs

9Kgs/20Lbs



Single Output


NP - 9912 / 9918 / 9925

(Linear mode)

Description

The NP - 9900 series is a cost effective and general purpose DC regulated supply with adjustable output voltage and overload warning light. The low ripple and noise feature make it e s p e c i a l l y s u i t a b l e f o r u s e w i t h t e l e communication equipment.

Features

• 1 - 15V DC adjustable output

• Fixed voltage mode at 13.8VDC

• Temperature control variable speed cooling fan



• Output current limit is depended on output voltage



• Housing available in Pantone warm grey 1C or

Pantone 433C dark grey

30

20

10

0


2 4 6 8 10 12 14 15


NP - 9925

NP - 9918

NP - 9912


Output Voltage





Load Regulation

Line Regulation

Input Voltage

V Meter Range

A Meter Range


Cooling System


Approvals


Weight

Accessory

NP - 9912

1 - 15VDC

13.8VDC

12A

NP - 9918 NP - 9925

15A

10mV

30mV

10mV

18A

20A

40mV

25A

30A

50mV


0 - 20V

0 - 15A 0 - 20A

7% fsd

Variable Speed Thermally Control Fan

0 - 30A


CE EN 61558 , EN 55014

205 x 115 x 275mm / 8 x 4.5 x 10.8in.

5.5Kgs / 12Lbs 7Kgs / 15.4Lbs

User Manual

9Kgs / 20Lbs



Description

This series merge the low ripple, high precision output of laboratory graded Linear Regulated Power Supplies with Full

Remote Programming and Data Logging functionality.

The popular USB and versatile RS-485 interface are built in with the unit for full remote programming and data logging with personal computer.

One PC can control and data log up to 31 power supplies of different models of this series via RS-232/RS-485 Adapter.

With our software, the power supply can operate up to 9 different sets of voltage and limit current; and 20 sequential timed-steps. The remote program also can store up to 100 sequential timed-steps of different sets of voltage, current and the running time up to 999 repetitive cycles and controls power supply. All the collected data from each power supplies during operation can be stored in MS Excel (.xls) format.

can integrate with their own software with the power supply for full remote programming functions.

In addition to the tracking OVP (Over Voltage Protection), there is an user preset upper output voltage limit, which prevents voltage adjustment over the preset limit.

This feature is vital in preventing damage to delicate, voltage sensitive test piece & PCB.

Programmable


NDP - 4185 / 4303 / 4601

(Linear mode)

Features

• Linear mode for high precision, low noise output,

• Excellent Load and Line regulation,

• Full remote programming and data logging,

• Built-in USB and RS232/485 interface which can control up to

31 units,

• Local or remote programmable cyclic run up to 20 sets of V, I , operational periods,

• 9 preset voltage and current at keypad and software,

• 20 sequential timed steps can be stored in power supply or computer,

• 100 sequential timed steps can be stored in computer,

• CC & CV indicators with auto-cross over,

• 4 digits LED high resolution ammeter and voltmeter,

• Tracking OVP and user preset maximum output voltage.


R&D works, Quality Control, Production especially in applications which require groups of different settings of output voltage, current limit levels for various cyclic operation period and records of output reading with dynamic loading during tests. It is ideals for applications with multiple power supplies at various locations with one centralized PC control.


Output Voltage

Output Current

Output Rated Power


Load Regulation (Voltage)

Line Regulation (Voltage)

Load Regulation (Current)

Line Regulation (Current)

Input Voltage

Power Consumption

Display Meter

Meter's Accuracy

Indicators

Cooling System

Operating Temperature

Protections

Approvals


Weight

Accessories

Optional Accessory

Remarks

Remote Programming Specifications

NDP - 4185

0 - 18VDC

NDP - 4303

0 - 30VDC

0 - 3A 0 - 5A

90W

3mVrms

5mV

3mV

5mA

4mV

4mA

2mA


Approx. 220V A/W

4 digits - Display LED Ammeter and Voltmeter

±0.1% +2 counts

NDP - 4601

0 - 60VDC

0 - 1.5A

5mV

4mA

Constant Current & Constant Voltage LED Indicators

Natural Convection

5 - 40°C

Tracking OVP (Over Voltage Protection), Current Limiting and Over Temperature Protection

CE-EMC : EN55011 , CE-LVD : EN 61010

205 x 115 x 275mm / 8 x 4.5 x 10.8in.

Approx. 5Kgs / 11Lbs

User Manual, Application Software for windows, LabView™ Driver, Command Set, USB1.1 Driver,

USB Cable, RS-485 Connector and One 120Ohm Resistor

RS-232 to RS-485 Adaptor (ATR-2485)

Adjustable Upper Voltage Limit, Power Factor Correction

Communication Interface

(USB1.1 Single Power Supply) and (RS-485 up to 31 Power Supplies)

Remote Programming Functionality

Full Control of Power Supply Functions and Data Read-back

Data Logging

Baud Rate

Yes, with supplied software

9600bps



100W

Switching Mode power supply

NRP - 2050 (20V5A) / 3630 (36V3A) / 6016 (60V1.6A)

Description

This series of 100W Switching Mode Power Supplies with

Current Limiting Control, is designed with the objectives of cost effectiveness, compactness and easy portability.

The slim tower housing makes it ideal for tight work bench. It is light and conveniently portable with a collapsible handle.

The large and illuminated LCD display provides clear and sharp readings even under dim light. The output power on off switch allows safe and handy operations. The Tracking OVP

(Output Over Voltage Protection) ensures a better and tighter protection to voltage sensitive loads .It has good line and load regulations, high efficiency and low ripple & noise that are typical of advanced switching mode power supply.

It meets the CE safety standards of EN-61010 for laboratory grade power supply and respective EMC standards.

Features

• Automatic Cross over CV and CC mode

• Illuminated LCD indications of A, V, Output On-OFF,

CC & CV.

• 3 digit displays of Volt and Amp meters

• Voltage and Current controls

• Compact slim tower housing

• Collapsible handle

• Output power on off switch at front panel

• Natural Convection

• Tracking OVP (output over voltage protection),

Short circuit, overload and over temperature protections.

• Good line, load regulations and low ripple and noise

• CE approvals


Input Voltage (Jumper Selection)

Full Load Input Current at 230Vac

Output Voltage Adjustable Range

Output Current Adjustable Range

Voltage Regulation

Load from 10% to 100% Variation

Line from 180 to 264Vac Variation

Ripple & Noise in r.m.s.

Ripple & Noise (peak to peak)

Current Regulation




Switching Operation Frequency

Power Factor

Efficiency at Maximum Power

Voltmeter and Ammeter Display

Voltmeter Accuracy

Ammeter Accuracy

LCD Indication

Protection

CE Approvals

Cooling System

Dimensions in mm (WxHxD)

Weight in Kg

NRP - 2050 NRP-3630

90 - 130 / 180 - 240Vac , 50Hz~

0.83A

1.0 - 20Vdc

0 - 5A

1.0 - 36Vdc

0 - 3A

70mV

20mV

5mV

30mV

50mV

30mV

NRP-6016

1.0 - 60Vdc

0 - 1.6A

50mV

50mV

20mA

20mA

20mA

80KHz to 120KHz

0.68

84%

3 Digit

85% 85%

±1% +5counts for range V≤5V

±1% +3counts for range V>5V



±1% +5counts for range I≤2A ±1% +5counts for range I≤1A

±1% +3counts for range I>2A ±1% +3counts for range I>1A

CC, CV, Amp, Volt, Output ON-OFF

Short Circuit, Overload, Over Temperature, Tracking OVP

LVD : EN 61010 , EMC : EN 55011

Natural Convection

70 x 150 x 250mm / 2.8 x 6.0 x 9.8in.

2Kgs / 4.4Lbs



±1% +5counts for range I≤0.5A

±1% +3counts for range I>0.5A



100W


NSP - 2050 (20V5A) / 3630 (36V3A) / 6016 (60V1.6A)

Description

This series of 100W Switching Mode Power Supplies with Current

Limiting Control, is designed with the objectives of high accuracy, compactness and easy portability.

Wire wound potentiometers are used for voltage and current control.

4 digit display LCD of voltage and current for high precision. The slim tower housing makes it ideal for tight work bench. It is light and conveniently portable with a collapsible handle.

The large and illuminated LCD display provides clear and sharp readings even under dim light. The output power on off switch allows safe and handy operations. The Tracking OVP (Output Over Voltage

Protection) ensures a better and tighter protection to voltage sensitive loads. It has good line and load regulations, high efficiency and low ripple

& noise that are typical of advanced switching mode power supply.

It meets the CE safety standards of EN-61010 for laboratory grade power supply and respective EMC standards.

Features

• Automatic Cross over CV and CC mode

• Illuminated LCD indications of A, V, Output On-OFF,

CC & CV.

• 4 digit displays of Volt and Amp meters

• Wire wound potentiometers for Voltage and Current controls

• Voltage and Current controls

• Compact slim tower housing

• Collapsible handle

• Output power on off switch at front panel

• Natural Cinvection

• Tracking OVP (output over voltage protection),

Short circuit, overload and over temperature protections.

• Good line, load regulations and low ripple and noise

• CE approvals


Input Voltage (Jumper Selection)


Output Voltage Adjustable Range

Output Current Adjustable Range

Voltage Regulation



Ripple & Noise in r.m.s.


Current Regulation




Switching Operation Frequency

Power Factor


Volt and Amp Potentiometer Type

Voltmeter and Ammeter Display



LCD Indication

Protection

CE Approvals

Cooling System


Weight in Kg

NSP - 2050 NSP-3630

90 - 130 / 180 - 260Vac , 50Hz~

0.83A

1.0 - 20Vdc

0 - 5A

1.0 - 36Vdc

0 - 3A

70mV

20mV

5mV

30mV

50mV

30mV

NSP-6016

1.0 - 60Vdc

0 - 1.6A

50mV

50mV

20mA

20mA

20mA

80KHz to 120KHz

0.68

84%

Wire Wound

4 Digit

±0.5% +5counts for range V≤5V

±0.5% +3counts for range V>5V

85% 85%

±0.5% +5counts for range V≤10V ±0.5% +5counts for range V≤20V

±0.5% +3counts for range V>10V ±0.5% +3counts for range V>20V

±0.5% +5counts for range I≤2A

±0.5% +3counts for range I>2A

±0.5% +5counts for range I≤1A

±0.5% +3counts for range I>1A

CC, CV, Amp, Volt, Output ON-OFF

Short Circuit, Overload, Over Temperature, Tracking OVP

LVD : EN 61010 , EMC : EN 55011

Natural Convection

70 x 150 x 250mm / 2.8 x 6.0 x 9.8in.

2Kgs / 4.4Lbs

±0.5% +5counts for range I≤0.5A

±0.5% +3counts for range I>0.5A



High Power Industrial Grade Linear Regulated Power Supply

With Remote Sensing / Remote Control and adjustable tracking OVP

PSD - 1550

(Linear mode)

Description

This industrial grade linear mode circuitry design ensures consistent low ripple and noise for this series of 750W power supplies. Coarse and fine voltage control for quick and precise voltage adjustment, automatic cross over CC mode with current control.

The unique wide range adjustable tracking OVP is made especially for various voltage sensitive loads that the usual factory preset OVP cannot cover . This special feature also makes simulation of battery in the test of UPS or charger workable without prematurely shut down due to factory preset OVP .

Full remote control terminals (voltage , current , and output on/off ) and Remote sensing make these power supplies suitable for any location from the loads .

With optional accessories the unit can be converted easily to rack mountable unit.

Features


• Adjustable tracking OVP

• Full Remote control functionality

• Remote sensing for precise applied loading voltage

• Automatic cross over CC, CV mode

• 4 digit LED display meters

• Rack mountable


Output Voltage


Output Current




Load Regulation (voltage)

Line Regulation (voltage)

Load Regulation (current)

Line Regulation (current)

Input Voltage

Display Meter


Indicators

Cooling System


Special Feature

Protections

Approvals


Weight

PSD - 1550

0 - 15Vdc

Coarse and Fine Potentiometer

0 - 50A

One Potentiometer

750W

4mV

0.02% +15mV

0.02% +5mV

0.15% +10mA

0.1% +10mA

230Vac , 50Hz~ ( or on request )


±0.5% +3 counts

Constant Current and Constant Voltage LED Indicators

Constant Speed Fan

0 - 40°C

Remote Output ON / OFF, Voltage and Current Control,

Remote Sensing

Tracking OVP ( Over Voltage Protection )

( 10% - 100% Adjustable for PSD-1550 )

Over Temperature, Short Circuit

CE EMC : EN 55011 , LVD : EN 61010

357 x 186 x 441 mm / 14 x 7.3 x 17.4in.

Approx. 28kgs / 62lbs




With Remote Sensing / Remote Control and adjustable tracking OVP

PSD - 3030 / 5020

(Linear mode)

Features Description

This industrial grade linear mode circuitry design ensures consistent low ripple and noise for this series of 900W power supplies. Coarse and fine voltage control for quick and precise voltage adjustment, automatic cross over CC mode with current control.

The unique wide range adjustable tracking OVP is made especially for various voltage sensitive loads that the usual factory preset OVP cannot cover . This special feature also makes simulation of battery in the test of UPS or charger workable without prematurely shut down due to factory preset OVP .

Full remote control terminals (voltage , current , and output on/off ) and Remote sensing make these power supplies suitable for any location from the loads .

With optional accessories the unit can be converted easily to rack mountable unit.


• Adjustable tracking OVP

(10-100% PSD-3030, 10-80% PSD-5020)

• Full Remote control functionality

• Remote sensing for precise applied loading voltage

• Automatic cross over CC, CV mode

• 4 digit LED display meters

• Rack mountable


Output Voltage


Output Current








Input Voltage

Display Meter


Indicators

Cooling System


Special Feature

Protections

Approvals


Weight

PSD-3030

0 - 30Vdc

PSD-5020

0 - 50Vdc

Coarse and Fine Potentiometer

0 - 30A

One Potentiometer

0 - 18A

900W

4mV 6mV

0.02% +5mV

0.02% +5mV

0.2% +10mA 0.1% +10mA

0.1% +10mA



±0.5% +3 counts


Constant Speed Fan

0 - 40°C

Remote Output ON / OFF, Voltage and Current Control, Remote Sensing

Tracking OVP ( Over Voltage Protection )



Over Temperature, Short Circuit

CE EMC : EN 55011 , LVD : EN 61010

357 x 186 x 441 mm / 14 x 7.3 x 17.4in.





With full Remote Programming & Remote Sensing.

PSM - 1550

(Linear mode)

Description

This series merge the low ripple, high precision output of industrial graded Linear Regulated Power Supplies with Full Remote Programming,

Data Logging & Remote Sensing functionality.

The popular RS-232 and versatile RS-485 interface are built in with the unit for full remote programming and data logging with personal computer.


The power supply can operate up to 9 different sets of voltage and limit current; and 20 sequential timed-steps at the front panel.

With our software, 100 sequential timed-steps of different sets of voltage, current and running time, up to 999 repetitive cycles can be programmed using any computer.

All the collected data from each power supplies during operation can be stored in MS Excel™ (.xls) format.

integrate with their own software with the power supply for full remote programming.

In addition to the tracking OVP (Over Voltage Protection), there is an user preset upper output voltage limit, which prevents voltage adjustment above the preset limit.

This feature is vital in preventing damage to delicate, voltage sensitive test piece.

The REMOTE CONTROL feature allows for full control including output on/off of the power supply without computer in a stand alone situation.

Features




• Built-in RS232/485 interface which can control up to 31 units,

• Supplied with software, command sets and LabView driver,



• 20 sequential timed steps can be stored in power supply and computer,

• 100 sequential timed steps can be stored in computer.

• Remote Sensing and separate Remote Control terminals.







Output Voltage

Output Current







Input Voltage

Display Meter



Indicators

Cooling System


Protections

Approvals


Weight

Accessories

Driver,

PSM-1550

0 - 15Vdc

0 - 50A

750W

4mV

0.02% +15mV

0.02% +5mV

0.15% +10mA

0.1% +10mA



0.5% +2 counts

0.5% +4 counts


Fan Cooling

0 - 40°C

Tracking OVP ( Over Voltage Protection ), Current Limiting

CE EMC : EN 55011 , LVD : EN 61010

357 x 186 x 441mm / 14 x 7.3 x 17.4in.


®


Remark




Data logging

Baud Rate

Command Set, RS-232 Cable, RS-485 Connector and one

120ohm Resistor

RS-232 to RS-485 Adapter ( ATR-2485 )

Adjustable Upper Voltage Limit

RS-232 and RS-485 ( up to 31 Power Supplies )

Full control of power supply functions and data read-back


9600bps




With full Remote Programming & Remote Sensing.

PSM - 3030 / 5020

(Linear mode)

Description

This series merge the low ripple, high precision output of industrial graded Linear Regulated Power Supplies with Full Remote Programming,

Data Logging & Remote Sensing functionality.

The popular RS-232 and versatile RS-485 interface are built in with the unit for full remote programming and data logging with personal computer.


The power supply can operate up to 9 different sets of voltage and limit current; and 20 sequential timed-steps at the front panel.

With our software, 100 sequential timed-steps of different sets of voltage, current and running time, up to 999 repetitive cycles can be programmed using any computer.

All the collected data from each power supplies during operation can be stored in MS Excel™ (.xls) format.

integrate with their own software with the power supply for full remote programming.

In addition to the tracking OVP (Over Voltage Protection), there is an user preset upper output voltage limit, which prevents voltage adjustment above the preset limit.

This feature is vital in preventing damage to delicate, voltage sensitive test piece.

The REMOTE CONTROL feature allows for full control including output on/off of the power supply without computer in a stand alone situation.

Features




• Built-in RS232/485 interface which can control up to 31 units,

TM

• Supplied with software, command sets and LabView driver,



• 20 sequential timed steps can be stored in power supply and computer,

• 100 sequential timed steps can be stored in computer.

• Remote Sensing and separate Remote Control terminals.







Output Voltage

Output Current







Input Voltage

Display Meter



Indicators

Cooling System


Protections

Approvals


Weight

Accessories

PSM-3030

0 - 30Vdc

0 - 30A

900W

4mV

0.02% +5mV

0.02% +5mV

PSM-5020

0 - 50Vdc

0 - 18A

6mV

0.1% +10mA

0.1% +10mA

0.2% +10mA



0.5% +2 counts 0.5% +3 counts

0.5% +2 counts 0.5% +2 counts


Fan Cooling

0 - 40°C

Tracking OVP ( Over Voltage Protection ), Current Limiting

CE EMC : EN 55011 , LVD : EN 61010

357 x 186 x 441 mm / 14 x 7.3 x 17.4in.


®

RS-232 Cable, RS-485 Connector and one 120ohm Resistor


Adjustable Upper Voltage Limit


Remark




Data logging

Baud Rate




9600bps



Remote Programming

Switching Mode DC Regulated Power Supply

SDP - 2210 / 2405 / 2603

Description

A programmable cyclic sequence of up to 20 sets of operational periods, voltage, & limiting current level can be set at the unit's keypad or by remote PC (Personal Computer) interface.

Groups of control settings and cyclic sequence can be stored in the PC and input to selected power supply via RS232/RS485.

With our supplied software , all the collected data of output voltage & current from each power supplies during operation can be stored as XLS

(Excel™) file format in the PC.

When using RS-485 , one personal computer can control and data log as many as 31 power supplies of different models of the same series.

In addition to our supplied software, Command Sets and Labview® driver are supplied with the unit so that users can integrate with their own software .

In the stand alone operation, the informative LCD display guides users for various functions such as preset output, programmable cyclic sequence operation.

In addition to the tracking OVP (Over output Voltage Protection), there is an upper output voltage limit which prevents voltage setting over the preset limit .

The output upper voltage limit is user preset.

This feature prevents damage to voltage sensitive load.

Main Features

• Full remote programming and data logging.

• Local or remote programmable cyclic run up to 20 sets of V, I, operational period.

• Built in RS-232/485 interface which controls up to 31 units.

• Supplied with software, command sets and Labview® driver.

• 9 user preset outputs at keypad

• CC & CV indicators with auto-cross over.

• 4 digit ammeter, voltmeter and power meter display.

• Tracking OVP and user preset max. output voltage.


R&D works, Quality control, Production especially in applications which require groups of different settings of output voltage , current limit levels for various cyclic operation period and records of outputs readings with dynamic loading during tests.

It is ideal for applications with multiple power supplies at various locations with one centralized PC control.


Output Voltage

Output Current


Ripple & Noise ( Peak to Peak )

Load Regulation

Line Regulation

Input Voltage

Input Power

Power Factor

Display Meter

Meter Accuracy

LCD Dimension

Cooling System


Protections

Approvals


Weight

Accessories

SDP - 2210

1 - 20Vdc

0 - 10A

200W

30mV p-p

300mV

10mV

SDP - 2405

1 - 40Vdc

0 - 5A

200mV

SDP - 2603

1 - 60Vdc

0 - 3A

150mV

100 - 240Vac , 50Hz~ / 60Hz~

285W

≥0.9

4 digits - Display LCD Ammeter, Voltmeter and Power meter

(±1% +5 counts for range V<5V , I<0.5A)

(±1% +2 counts for range V ≥5V , I ≥0.5A)

48 x 66mm


0 - 40°C

Tracking OVP (Over Voltage Protection), Current Limiting, Over Temp. Protection

CE EMC : EN 55011 , LVD : EN 61010

193 x 98 x 215mm / 7.6 x 3.9 x 8.5inch

3kgs / 6.6lbs

®

Command Set, RS-232 Cable, RS-485, Connector and one 120ohm Resistor


Adjustable Upper Voltage Limit, Power Factor Correction


Remark




Data logging

Baud Rate




9600bps



Description

This family of high power remote sensing, remote control, switching mode CC/CV power supply offers unique solution for various loading conditions and applications.

The remote control functionality makes

1. output on/off possible without turning the power on/off switch of the unit.

2. adjusting the output voltage and current without turning the controls of the unit.

The remote sensing capability is important for load away from the power supply or when load current becomes erratic.

It is ideal for applications that require precise voltage at the point of application

When using it as a normal bench power supply, the 10-turn potentiometers provide precise output voltage and current control.

The 4 digit LED meters with clear indication of automatic cross over of CC and CV mode provide easy read outs.

With the optional accessory, unit can be easily converted to 19" rack mount construction in less than 5 minutes.

It is suitable for a wide range of applications such as production testing, laboratory, field test of voltage critical distant load, telecommunications, powering of dc network and etc.

900W Switching Mode Power Supply with C.C, C.V, REMOTE CONTROL & SENSING

SIM - 9106 / 9303

Features

• Remote control for output power on-off .

• Remote control for voltage and current adjustment.

• Remote sensing for remote point of precise voltage regulation.

• Do It Yourself 19" Rack Mount with optional accessory.

• High RFI stability.

• CC & CV mode with auto-cross over.

• Output Over Voltage Protection.

• Active Power Factor Correction.

• Overload, Over-temperature, Short circuit Protections

• 10-turn wire wound potentiometers .

• 4 digit LED A and V meters.

• Thermally controlled variable speed fan.

• Universal Input 100-240VAC

Assembled with Do It Yourself

19" Rack Mount Front Panel



Variable Output Current

Load Voltage Regulation

Line Voltage Regulation

Load Current Regulation

Line Current Regulation

Ripple & Noise (Peak - Peak)


Input Voltage

Efficiency

Meter Type

Voltmeter Range

Ammeter Range

Meter Accuracy


Cooling System

Special Feature

Standard Accessory


Approvals


Weight

Remark

SIM - 9106

1 - 15Vdc

1 - 60A

0.1% +5mV

0.05% +3mV

SIM - 9303

1 - 30Vdc

1 - 30A

0.2% +5mA

0.1% +5mA

50mV p-p

<5mVrms

100 - 240Vac , 50 / 60Hz~

≥82%

≥83%

LED Meter

4 digits - Display

4 digits - Display

±0.5% +2 counts

Overload (Constant Current Limiting), Short Circuit, Over Temperature, OVP

Variable Speed thermally Control Fan

Remote Sensing, Remote Control

Remote Control Plug, User Manual

19" Rack Mount Kit (part no. SIM-9106 : 8781-9106-0000 / SIM-9303 : 8781-9303-0000)

CE EMC : EN 55011 , LVD : EN 61010

235 x 95 x 340mm / 9.3 x 3.8 x 13.4inch

6kgs / 13.2lbs

Power factor correction ≥0.97 at optional load



Low Profile & Small Foot Print

Fixed Voltage Switching Mode Power Supplies w Cigar Socket

SPA-8100 10A cont, 12A max @ 13.8V , SPA-8102 5A cont, 6A max @ 27.6V

Description

This series of convection cooled switching mode power supply is designed for radio equipment.

It is exceptionally immune to Radio Frequency

Interference at close range.

Heat is dissipated from the heat sink and the aluminum base for efficient natural cooling.

It has the small footprint of popular radio transceivers, and the low profile casing make it fall in place with a host of equipment in a tight spot.

The constant current protection, over temperature protection with constant current and output Over

Voltage Protection (OVP) ensure better reliability and safer protection to both the power supply and its connected load.

One main DC output at rear and a front mounted cigar socket provide convenient DC connectivity.

It has excellent line and load regulation, low ripple and noise , optimal efficiency of 80% and a power factor of 0.7.

Features

• Natural cooling for absolute quiet operation

• High RFI immunity

• Binding pole and cigar socket DC output.

• Over Load, Short Circuit, Over Temperature protections by constant current circuitry.

• Output Over Voltage Protection

• Power Factor Control

• User adjustable fine tune setting

13.3 ~14.5V (SPA-8100) & 26.6~29V (SPA-8102 )


Output Voltage

Output Current

( Main output posts )

( Main output posts + Cigar Socket )

Ripple & Noise

Load Regulation

Line Regulation

Input Voltage

Indicators

Cooling System


Protections

Approvals


Weight

SPA-8100

Fixed 13.8Vdc ±0.5V

SPA-8102


10A Cont. , 12A Max.

( 1 min. 50% duty cycle )



≤50mVp-p , 5mVrms

≤100mV ( 0 - 100% Load )

≤50mV ( ±10% Variation )

5A Cont. , 6A Max.


5A Cont. , 6A Max.



Red Color Overload LED Indicator

Air Convection

0 - 40°C

Over Load, Over Temperature, Short Circuit protections by Constant Current Circuitry and Output Over Voltage Protection

CE EMC : EN 55022 , LVD : EN 60950

181 x 63 x 190 mm ( 7.2 x 2.5 x 7.5 in. )

Approx. 1.55kgs ( 3.4lbs )





SPA-8150 15A cont, 18A max @ 13.8V , SPA-8152 7.5A cont, 8.5A max @ 27.6V

Description

This quiet running, switching mode power supply is designed for radio equipment.



The thermostatic variable speed cooling fan is hardly audible even at its maximum speed.





It gives a total continuous current output of 15A at

13.8V and a maximum of 18A at 50% duty cycle. It has excellent line and load regulation, low ripple and noise, optimal efficiency of 80% and a power factor of

0.7.

Features

• Fan cool







13.3 ~14.5V (SPA-8150) & 26.6~29V (SPA-8152 )


Output Voltage

Output Current



Ripple & Noise

Load Regulation

Line Regulation

Input Voltage

Indicators

Cooling System


Protections

Approvals


Weight

SPA-8150


SPA-8152






≤50mVp-p , 5mVrms

≤100mV ( 0 - 100% Load )


7.5A Cont. , 8.5A Max.


7.5A Cont. , 8.5A Max.




Fan Cool

0 - 40°C


CE EMC : EN 55022 , LVD : EN 60950

181 x 63 x 190 mm ( 7.2 x 2.5 x 7.5 in. )






SPA-8230 23A cont, 25A max @ 13.8V , SPA-8232 11.5A cont, 12.5A max @ 27.6V

Description

This series of convection cooled switching mode power supply is designed for radio equipment.



Heat is dissipated from the heat sink and the aluminum base for efficient natural cooling.





It has excellent line and load regulation, low ripple and noise , optimal efficiency of 80% and a power factor of 0.7.

Features

• Fan Cool







13.3 ~14.5V (SPA-8230) & 26.6~29V (SPA-8232 )


Output Voltage

Output Current



Ripple & Noise

Load Regulation

Line Regulation

Input Voltage

Indicators

Cooling System


Protections

Approvals


Weight

SPA-8230


SPA-8232






≤50mVp-p , 5mVrms

≤100mV ( 0 - 100% Load )


11.5A Cont. , 12.5A Max.


11.5A Cont. , 12.5A Max.




Fan Cool

0 - 40°C


CE EMC : EN 55022 , LVD : EN 60950

181 x 63 x 190 mm ( 7.2 x 2.5 x 7.5 in. )




Description

This series of high current, fixed voltage, regulated switching mode power supplies are built with, Over

Voltage Protection for safe-guarding voltage sensitive load. High efficiency cuts the running cost and dynamic Power Factor Corretor (PFC) maximizes the main's available power. They are suitable for applications in telecommunications such as radio equipments, RF amplifiers, and other high current applications like car audio, halogen, xenon spot light demonstrations.

The high grade Screw On output terminals are on the back panel of the console while the power on off switch and the bi-colour LED indicator (Power On

/Overload) is at the front.

The variable speed thermostatic control cooling fan ensures quiet operation of the power supply in medium load condition.

The small size console fits well with the footprints of most modern telecom equipments.

High Current


SPA - 8250 / 8400

Features


• Over voltage protection at 16.5V

• Current fold-back circuit with LED indicator

• Short circuit protection

• Over temperature cut off protection

• High efficiency >78%

• Power factor correction >0.95

• Variable speed Thermostatic controlled fan quiet operation

• Light weight and small size

• Housing are available in (Pantone warm grey 1C or Pantone 433C dark grey)




Ripple & Noise (Peak-Peak)

Load Regulation

Line Regulation

Input Voltage

Efficiency

Dynamic Power Factor Correction

Cooling Method


Indicators

Approvals


Weight

SPA-8250

Fixed 13.8Vdc

25A

50mV

200mV

50mV


>78%

SPA-8400

Fixed 13.8Vdc

40A

>0.95


Over Load, Over Temperature, Short Circuit protections and Output Over Voltage Protection

Bi-Color LED (Green : Power ON / Red : Overload)

CE EMC : EN 55022 , LVD : EN 60950

220 x 110 x 220 mm 220 x 110 x 300 mm

(8.7 x 4.3 x 8.7 in.)

2.7kgs (5.9lbs)

(8.7 x 4.3 x 11.8 in.)

3.5kgs (7.7lbs)



High Current Rack Mount


SPP - 8250 / 8251

Description

This series of U2 ,19-inch rack mount, high current, regulated switching mode power supplies are built with

,Over Voltage Protection for safe-guarding voltage sensitive load. They are suitable for applications that require radios.

The dynamic Power Factor Corrector (PFC) maximizes the main's available real power and minimizes harmonics back to the mains thus beneficial for other AC equipments in the cabinet rack. The high efficiency of this switching power supply cuts the running cost .

The high grade Screw On output terminals are on the back panel of the casing while the power on off switch and the red LED overload indicator is at the front panel.

The variable speed thermostatic control 8cm cooling fan ensures quiet operation of the power supply even in medium load condition.

The casing is made of powder coated galvanized steel with anodized aluminum front panel and handles.

Features


• Over voltage protection

• Current fold back overload protection with red LED indicator


• Over temperature cut off protection

• High efficiency >78%

• Power Factor Correction >0.95

• Variable speed thermostatic controlled fan for quiet operation.

• Light weight and small size.


Rated Output Voltage



Load Regulation

Line Regulation

Input Voltage

Efficiency


Cooling Method


Indicators

Meter Type

Approvals


Construction

Weight

SPP - 8250

3 - 15VDC

25A

50mVp-p

200mV ( 0 - 100% Load )

50mV ( ±10% Variation )

SPP - 8251

Fixed 13.8VDC

28A


>0.78%

>0.95


Over Load, Over Temperature, Short Circuit Protection and Output Over Voltage Protection


Analog

Design & Manufacture to comply with CE EMC LVD Standards

Main Case 220 x 89 x 225 mm ( 8.7 x 3.5 x 8.9 in. )

U2 19inch Rack Mount, power coated galvanized steel casing, anodized aluminum front panel and handles




Description

This series of 200 Watts LABORATORY GRADE

SWITCHING DC POWER SUPPLIES are built with precision coarse and fine output voltage and current limiting controls. The OVP ( output over voltage protection ) protects voltage sensitive load by instant shutting down the supply when output voltage is in excessive to the set voltage due to line surge or otherwise. Current limiting control with automatic cross over of constant voltage (CV) and constant current (CC) mode makes this series ideal for R&D work in laboratory situations.

LABORATORY GRADE SINGLE OUTPUT


SPS - 2210 / 2405 / 2603

Features

• 200 Watts output power

• Coarse and Fine Voltage / Current controls

• Auto-cross over CV and CC

• LED indicators for CV and CC mode


• Excellent load and line regulation

• Thermostat control fan cooling

• 3½ digit displays of voltmeter and ammeter

• OVP, Overload, Short circuit and Over temperature protections

• Output ON-OFF push button


Output Voltage





Load Regulation

Line Regulation

Input Voltage

Meter Type

Voltmeter Range

Ammeter Range


Indicators

Cooling System


Approvals


Weight

SPS - 2210

1 - 20VDC

Fine and Coarse Adjust

0 - 10A

Fine and Coarse Adjust

20mVp-p

0.5% +250mV

50mV

90 - 265Vac , 50/60Hz~

Digital LED

3½ digit LED

3½ digit LED

1% +2 counts

SPS - 2405

1 - 40VDC

0 - 5A

0.5% +200mV

Constant Current & Constant Voltage

Thermostatic control fan

Over Voltage, Short Circuit, Over Temperature

CE EMC : EN 55011 , LVD : EN 61010

205 x 115 x 275 mm ( 8 x 4.5 x 10.8 in. )

3kgs (6.6lbs )

SPS - 2603

1 - 60VDC

0 - 3.3A

0.5% +200mV



900W Reversible Polarity & AH Meter


SPS - 5600 / 5602

Description

This series of power supplies are designed for the

Electrochemical surface treatment industry.

This 900W switching mode DC regulated power supply is designed for applications which require frequent reverse polarity operations and logging of precise Ampere Hour record.

Electronic safety locking of the Reverse Polarity Switch such that when the in process current is higher than 2Amp, the switch is deactivated. The switch becomes functional again when load is taken away or load current is less than 1

.

This power supply provides high current with constant current limiting protection, and a highly efficient Active

Power Factor Correction.

High quality wire wound potentiometer is used for voltage control for precision adjustment of the output voltage.

Features

• Designed for Electrochemical treatment Industries.

• Reversible Polarity with Auto Lock Protection

(2Amp)

• Precision 6digit AH meter with Logging & Reset

• Constant Current Protection

• Active Power Correction

• Wire Wound Potentiometer

• Floating Ground Design






Load Regulation

Line Regulation

Input Voltage

Efficiency


Voltmeter & Ammeter Display


Indicators

Special Features

AH Meter Specification

Cooling Method


Protection

Approvals


Weight

SPS - 5600

1 - 15Vdc

60A

100mVp-p

250mV

10mV

100 - 240Vac , 50/60Hz~

>81%

SPS - 5602

1 - 30Vdc

30A

>0.97 at optimal load

4 digit LED display

±1% +1 digit

Red LED for overload / Short circuit indication

Reverse Polarity Indicator

Reverse Polarity Switch with electronic safety lock out at load current high than 2A

AH Meter with Reset

6 digit display (999999) ; 14.2mm Red LED

Accuracy 5% of reading value


0 - 40°C

Overload (Constant Current Limiting),

Short Circuit, Over temperature and Output Over Voltage Protection OVP

CE EMC : EN 55011 , LVD : EN 61010

425 x 125 x 355 mm ( 16.7 x 4.9 x 14 in. )

8.7kgs ( 19lbs )



Description

This portable, compact & light weight, fixed

12V regulated DC power supply provides a stable output voltage regardless of current drain to 3A continuous operation. It is suitable for voltage sensitive devices like, CCTV cameras, Intercom,

Scanners, CB Radios and Power supply for the hobbyist.

The latest switching mode circuitry makes this unit a High efficient, Reliable and Highly stable regulated power supply at a competitive price.

Fixed Output

Switching Mode Regulated Power Supply

SPS - 8040 / 8042

Features

• Fixed 12V DC output

• Regulated stable output

• Overload and Short circuit protection

• LED power on indicator

• Poly-carbonate housing

• Streamline design for desktop operation


Output Voltage



Load Regulation

Line Regulation


Input Voltage

Indicators

Cooling System


Approvals


Weight

SPS - 8040

12VDC

3A

5A

300mV

60mV

SPS - 8042

13.8VDC

3A

5A

100mV

50mV

60mVp-p 50mVp-p


Power on LED

Natural Convection

Output Over Load and Short Circuit Protection

CE EMC : EN 60950 LVD : 55022

90 x 50 x 140 mm (3.6 x 1.9 x 5.5 in. )

450g ( 16oz. )



Multi - Voltage

Switching Mode Regulated Power Supply

SPS - 8041

Description

This portable, compact & light, regulated DC power supply provides a range of stable output voltages regardless of current drain to 3A continuous operation.

This output voltage is user selectable at the front panel. It is suitable for voltage sensitive devices like, CCTV cameras, Intercom, Scanners,

CB Radios and Power supply for the hobbyist.

The latest switching mode circuitry makes this unit a High efficient, Reliable and Highly stable regulated power supply at a competitive price.

Features

• User selectable output voltages at 3, 4.5, 6, 7.5,

9, 12VDC

• Continuous 3A operation

• Overload and Short circuit protection


• Poly-carbonate housing

• Streamline design for desktop operation


Output Voltage



Load Regulation

Line Regulation


Input Voltage

Indicators

Cooling System


Approvals


Weight

SPS - 8041

3, 4.5, 6, 7.5, 9, 12VDC

3A

5A

300mV

60mV

60mVp-p


Power on LED

Natural Convection

Output Over Load and Short Circuit Protection

CE EMC : EN 60950 LVD : 55022

90 x 50 x 140 mm (3.6 x 1.9 x 5.5 in. )

450g ( 16oz. )



Description

The series of HIGH POWER SWITCHING

MODE DC REGULATED POWER SUPPLIES provide high current 25 Amps output in a lightweight and compact size case. They are suitable for a wide range of uses, such as radio equipment, and are ideal for high power car stereo work. In addition to variable output from 3 to 15VDC, a fixed 13.8VDC can be selected.

Overload, Over temperature, and Over voltage protection are standard.

High Current


SPS - 8250 / 9250

Features

• 25A current output

• High efficiency

• Adjustable output voltages 3V to 15V

• 13.8V lock control


• Overload temperature protection


• Variable speed thermally controlled fan.



• Housing are available in Pantone warm grey

1C or Pantone 433C dark grey



Fixed Output Voltage Mode



Load Regulation

Line Regulation

Input Voltage

Efficiency

Meter Type

Voltmeter Range

Ammeter Range


Cooling System


Approvals


Weight

Remarks

SPS - 8250

3 - 15Vdc

13.8Vdc

25A

50mV

200mV

50mV


>78%

Analog Meter

0 - 20V

0 - 30A

7% fsd

SPS - 9250

LED Meter

3 digit display

3 digit display

1% +2 counts


Overload, Over Temperature, Short Circuit, OVP protections

CE EMC : EN 55022 , LVD : EN 60950

220 x 110 x 220 mm ( 8.7 x 4.3 x 8.7 in. )

2.7kgs ( 6lbs )

Power factor correction >0.95 at optimal load



High Current


SPS - 9252

Description Features

The HIGH POWER SWITCHING MODE

DC REGULATED POWER SUPPLY provides

12 Amps output in lightweight and compact size case. They are suitable for a wide range of uses, such as mobile radio equipment. In addition to variable output from 3 to 30VDC, a fixed

13.8VDC can be selected.



• High efficiency


• 13.8V Lock Control



• Over voltage protection at 33V

• Variable speed thermally controlled fan









Ripple & Noise (rms)

Load Regulation

Line Regulation

Input Voltage

Efficiency

Meter Type

Voltmeter Range

Ammeter Range


Cooling System


Approvals


Weight

Remarks

SPS - 9252

3 - 30Vdc

13.8Vdc

12A

5mVrms

200mV

50mV


>82%

LED Meter

3 digit display

3 digit display

1% +2 counts

Variable speed thermally controlled fan


CE EMC : EN 55022 , LVD : EN 60950

220 x 110 x 220 mm ( 8.7 x 4.3 x 8.7 in. )

2.7kgs ( 6lbs )




Description




High Current


SPS - 8400 / 9400

Features


• High efficiency



• Fixed voltage mode at 13.8V















Load Regulation

Line Regulation

Input Voltage

Efficiency

Meter Type

Voltmeter Range

Ammeter Range


Cooling System


Approvals


Weight

Remarks

SPS - 8400

3 - 15Vdc

13.8Vdc

40A

50mV

200mV

50mV

230Vac , 50Hz~ ( 120Vac / 60Hz~ or on request )

>78%

Analog Meter

0 - 20V

0 - 45A

7% fsd

SPS - 9400

LED Meter

3 digit display

3 digit display

1% +2 counts



CE EMC : EN55011 EN55022 , LVD : EN 60950 EN61558

220 x 110 x 300 mm ( 8.7 x 4.3 x 11.8 in. )

3.5kgs ( 7.7lbs )




High Current


SPS - 9402

Description

Features







• 13.8V Lock Control



• Constant Current Protection prevents overloading

• Over voltage protection at 33-35V











Load Regulation

Line Regulation

Input Voltage

Efficiency

Meter Type

Voltmeter Range

Ammeter Range


Cooling System


Approvals


Weight

Remarks

SPS - 9402

3 - 30Vdc

13.8Vdc

20A

50mV

200mV

50mV

230Vac , 50Hz~ ( 120Vac / 60Hz~ or on request )

>78%

LED Meter

3 digit display

3 digit display

1% +2 counts



CE EMC : EN55011 EN55022 , LVD : EN 60950 EN61558

220 x 110 x 300 mm ( 8.7 x 4.3 x 11.8 in. )

3.5kgs ( 7.7lbs )




Description

This high current switching mode DC regulated output power corrector. The constant current limiting protection allows the

The remote sensing terminals are used to compensate for output line losses so that a precise regulation can be achieved for critical voltage application away from the power supply.

The output voltage level and ON-OFF can be externally controlled via the remote terminal.

It is ideal for applications that need good quality high DC current network with precise point of voltage regulation.

SPS-9600 / SPS-9602 has a small footprint for its 900W continuous maximum power.

It is suitable for a wide range of applications such as street blaster super high power car audio demonstration console, radio equipment and etc.

High Current with Remote Sinsing & Control


SPS - 9600 / 9602

Features

• Total max. continuous output current 60A (SPS-9600) / 30A

(SPS-9602)

• Main Output /Remote Sensing/ Remote Control/ terminals at the back

• Front terminals 5A (SPS-9600) / 3A (SPS-9602) limiting.

• ( Precise Load Point Voltage )

• Remote Sensing for remote point of regulation.

• Remote control terminals for output voltage adjustment and

*on/off*

• 29HR Count Down Timer (Optional) for Output ON/OFF


• Overload / Over-temperature / Short Circuit Protections

• Constant Current mode with LED indicator prevents overloading



• Active power factor correction ( P.F. >0.97 )

• Housing are available in Pantone warm grey 1C or Pantone

433C dark grey

• *Remote output on/off is an added function for production after Oct. 2004*



Total Rated Output Current

(Main Output + Front Output)

Rated Output Current (Main Output)

Rated Output Current (Front Output)

Load Regulation (Main Output)

Line Regulation (Main Output)


Input Voltage

Efficiency

Meter Type

Voltmeter Range

Ammeter Range



Cooling System

Special Feature

Approvals


Weight

Remarks

SPS - 9600

1 - 15Vdc

SPS - 9602

1 - 30Vdc

60A

60A

5A

0.1% +5mV

0.05% +3mV

50mVp-p


>85%

LED Meter

3 digit display

30A

30A

3A

3 digit display

±1% +1 count

Overload (Constant Current Limiting), Over Temperature, Short Circuit,

OVP protections


Remote sensing , Remote output voltage control and *on/off *

* Remote output on/off only for production after Oct. 2004 *

CE EMC : EN 55022 , LVD : EN 60950

220 x 110 x 360 mm ( 8.7 x 4.3 x 14 in. )

5.8kgs ( 12.8lbs )




High Current


SPS - 9620

Description

The SPS-9620 DC power supply has been designed for professional applications which require quality high current for equipments such as super power car audio that are normally operated from twelve volt batteries.

The output is current limited at just over 120A and this current output can be supplied continuously.

The output voltage has Over Voltage Protection at about

17V to ensure very high protection against power supply failure, thus offering full protection to the powered equipment .

The excellent load regulation is further enhanced with remote sensing terminals to give precise voltage at the point of application for long connecting leads.

The output voltage range can be easily fine tuned between 12.6V to 14.3Vvia a concealed trimmer. This covers most 12V battery sources such as six lead –acid cells

(13.8V) or ten nickel-cadmium cells (12.6V) and etc.

The excellent Dynamic Power Factor Correction (>0.9) reduces unnecessary power loss (cuts electricity cost in some countries) and cuts the noise and EMI to your power mains.

Features

• Output Over Voltage Protection at 16.5V Trimmer fine tune output voltage 12.6 to 14.3 V for 13.8 V nominal .

• Constant Current Limiting Over Load Protection Short circuit and Over temperature Protection.

• Green LED for power on/off indication

• Red LED for overload / short circuit protection

• Excellent line and load regulation.

• Remote sensing terminal for precise voltage load with long leads.


• Cooling fan is on all the time, speed of fan increase with temperature of unit.

• High efficiency 85%

• CE Approval : EN55022, EN61000, EN-55024

• IEC 60950:1999+Corr.Jan.2000,

EN 60950:Corr.Feb.2002

• Light weight and Compact:11Kg., 23W x 22H x 34D cm


Output Voltage



Load Regulation (with sense)

Load Regulation (with no sense)

Line Regulation

Input Voltage

Efficiency


Indicator

Special Feature

Cooling Method


Protections

Approvals


Weight

SPS - 9620

Fixed 13.8Vdc (Fine Tune 12.6-14.3Vdc)

120A

40mV p-p

0.1% +5mV

0.1% +5mV

0.05% +3mV

230Vac , 50Hz~ (or on request )

>85%

>0.97 at optimal load

Green LED for power on/off indication,

Red LED for overload/short circuit indication

Remote Sensing

Variable speed thermally static control fan

0 - 40°C

Overload (Constant Current Limiting),

Short Circuit, Over Temperature, OVP

CE EMC : EN55022 , LVD : EN 60950

235 x 218 x 345 mm ( 9.3 x 8.6 x13.6 in

.

)

11kgs ( 24lbs )



80W Constant Power


SSP - 7080

Description

This 80Watt constant power design allows a much wider range of output current and voltage than the most power supplies in the same category. The 3 voltage and current range selections in effect is like having 3 power supplies with different output range.

It has constant voltage and automatic cross over constant current, adjustable over voltage protection setting, high precision

4 digit meters making it an ideal choice for R&D bench top power supply.

Features

• Switching Mode Power Supply with Dynamic PFC

• 80W Constant Power conversion in 3 selectable ranges:

• 0~16V/0~5A; 0~27V/0~3A; 0~36V/0~2.2A

• User preset output voltage, current and over voltage protection limits.

• 4 digit LED Meter displays

• Output On-Off switch allows presetting of output voltage and current limiting in Off mode to ensure safe operating V&I limits when back to On mode.

• Remote sensing for accurate applied voltage at load point

• Output terminals at front and rear panels for easy operation.


Input AC Voltage Range

No load Input Current at 230Vac


AC Input Frequency

Efficiency

Power Factor

Constant Voltage and Current Range Selection:

0-16V / 5A selection I

0-27V / 3A selection II

0-36V / 2.2A selection III

Constant Voltage Characteristics :

Load Regulation (0-100%)

Line Regulation (±10%)


Constant Current Characteristics :



Meter Accuracy :



Protection

SSP - 7080

90 - 264Vac

≤0.1A

≤0.5A

47 - 63Hz~

≥75%

≥0.9

0 - 16.4V

0 - 27.6V

0 - 36.8V

≤20mV

≤4mV

≤30mV

≤10mA

≤10mA

0 - 5.1A

0 - 3.1A

0 - 2.3A


Additional Function

CE Approvals

Cooling


Weight in Kg

±1% +2 counts

±1% +2 counts

Adjustable Upper Voltage Limit,

Current Limiting Protection, Short Circuit, Overload,

Over Temperature Protection

Front and Back of housing

Remote Sensing

LVD : EN 61010 , EMC : EN 55011

Natural Convection

53.5 x 127 x 330mm / 2 x 5 x 13inch

Approx. 1.9Kgs / 4.2Lbs



Remote Programmable Constant Power Switching Mode power supply with Ethernet Network Connectivity / 3 DC Voltage Ramp Generators / 32 bit MCU

SSP - 8080

Next Generation Power Supply

Description

The constant power design allows a much wider range of output current and voltage than the most power supplies in the same category.

The 3 voltage and current range selections in effect is like having 3 power supplies with different output range.

An advanced ARM construction RISC 32bit Micro-Processor is used to provide the following unique features .

Three unique voltage generators and remote programming of accurate voltage and current, data logging of output voltage and current.

Through the various combinations of the settings in the time gradient and the duration of the voltage generators, miscellaneous repeatable ramp up / down, step, irregular wave form of output voltages can be generated from values of V, I & ∆T.

It is ideal for R&D, education, production, burn-in test especially for devices when the effect of irregular dc input is critical.

The standard communication port provided is USB1.1 which can be connected to your personal computer. Remote Control functions like output on-off, voltage and current adjustment, selection of voltage and current ranges can be done through your PC .

With the Ethernet control board (optional) and the ETHERNET

/USB router, connection to LAN or WAN network is made possible. One

PC can remotely control and monitor 250 power supplies with C type

Ethernet and more for B and A type networks.

It opens the door to use with all sorts of control and monitor software in cycling and output data acquisition even through the internet.

We provide application software, USB driver, command sets, Ethernet setting software, and Labview® driver for Ethernet .

This Ethernet / Internet ready SMPS is the dream power supply for the network savvy engineers to have the controls, monitoring and output data logging to be done via the internet in real time situation.

Features

Electrical

** Switching Mode Power Supply with Dynamic PFC

** 80W Constant Power Supply in 3 selectable ranges:

0~16V/0~5A ; 0~27V/0~3A ; 0~30V/0~2.2A

** Adjustable Upper Current and Voltage Limits in addition to the tracking OVP and CC.

** Separate indicator for Upper Current and Voltage Limits and Over

Temperature

** 4 digit LED meter displays and output on/off switch

** Coarse and fine tune selection

** 3 sets of user preset V and I Recalls ( A, B, C), for quick access of frequent V& I settings.

** Key pad lock and unlock function

** Remote sensing for accurate applied voltage at load point

DC Ramp, Step & Irregular Wave Function

** 3 sets of Voltage Generators with 0 to 600 seconds output time

** Preset time period from one Voltage Generator to another is 0 to 20 seconds

** Any 2 Voltage Generators can merge to form ramp up, ramp down

Step, Irregular waveform, in various duty cycles.

Remote Program & Network connectivity

** Remote control and programming of output on off, voltage & current setting, Choice of power supply range , and data logging to PC.

** USB1.1 port for PC interface with Ethernet router to Lan or Wan network and to the internet.

** One PC can control and monitor over 250 power supplies in the C

Ethernet

** Supply of application software, USB driver, command sets, Ethernet setting software and Labview® driver for Ethernet.


Input AC Voltage Range

No load Input Current at 230Vac


AC Input Frequency

Efficiency

Power Factor

Constant Voltage and Current Range Selection:

0-16V / 5A Range I

0-27V / 3A Range II

0-36V / 2.2A Range III

SSP - 8080

100 - 240Vac

≤0.1A

≤0.5A

47 - 63Hz~

≥75%

≥0.9

0 - 16.4V

0 - 5.1A

0 - 27.6V

0 - 3.1A

0 - 36.8V

0 - 2.3A

Constant Voltage Characteristics :




Constant Current Characteristics :



Meter Accuracy :

≤20mV

≤4mV

≤30mV

≤10mA

≤10mA

Voltmeter and Ammeter Accuracy

User Adjustable Upper Current and Voltage Limits

Number of Preset Recalls of Frequent use V&I Setting

±1% +2 counts

Yes

3

Remote Sensing

Ramp Step Irregular Waveform Functions

Yes

Number Voltage Generators (DV / Dt) 3 ( A, B, C )

Available Number of Combinations of Voltage Generators 6 ( AB, BA, AC, CA, BC, CB )

Settable Output Time Period of each Voltage Generator

Settable Time Period one Voltage Generator to another

Remote Programmable / Control by PC

Protection

Standard Communication Port

Optional Interface Accessory

Provided Software

CE Approvals

Cooling


Weight in Kg

0 to 600 seconds

0 to 20 seconds

Output ON/OFF, Voltage & Current Control, Selection of Voltage and Current Range,

Programmable of cyclic output and data logging of output

Adjustable Over Voltage Protection, Current Limiting Protection, Short Circuit,

Overload, Over Temperature Protection

USB 1.1

Ethernet Control Broad (ZNE-100PT) Factory Pre-installed or User Installable

USB Driver, Command Sets, Ethernet Setting Software, Labview® Driver for Ethernet

LVD : EN 61010 , EMC : EN 55011

Natural Convection

53.5 x 127 x 330mm / 2 x 5 x 13inch

Approx. 1.9Kgs / 4.2Lbs



Switching Mode

Programmable Automatic Charger for Lead-Acid Battery

SBC - 8112 / 8125 / 8215

Description

This series of Switching Mode Automatic Chargers are built for high current charging of flood and sealed (Gel and

AGM) types of Lead Acid Batteries. Charger can be safely left connected to battery all the time . Charging battery under loading is an added feature.

User selection of suitable Boost charge voltage according to battery manufacturer, recommendation, and the discharged state of the battery as well. Good line regulation and the switching mode technology allow large fluctuation of input voltage as typically as from dock power or generators. These plus the low ripple DC output will prolong the life of the batteries. Remote temperature sensor to protect battery from overheat during charging.

Safety Features

• Overload and Short Circuit protection

• Reverse polarity protection

• Over temperature protection to batteries by remote sensor

• Transformer isolated to protect against electrolysis

Features

• Two step charging

• Suitable for all types of Lead Acid Batteries

• Selection of Boost charge voltage and Semi Boost charge according to type and discharge state of battery

• Automatically change between float and boost charging mode

• Timed charging mode available. (2/4/8hrs. factory preset)

• Charger can be left connected to battery permanently

• LED indicator for different charging mode and battery over temperature

• Wide Input Voltage Range with good line regulation

• Active Power Factor Correction (available in Standard

CE version / optional on other version)

• High Efficiency 80%

• Light and Compact


Applicable Battery

Battery Type

Battery Voltage

Recommended Battery Capacity

Output (@ 25˚C)

Rate Current

Float Mode Voltage

Boost Mode Voltage

Charge Indicator LED

Line Regulation

Load Regulation (0-100% Load)

Ripple & Noise (RMS)

Efficiency

Input

Voltage Range

Frequency

Active Power Factor Correction

Protection

Overload Protection

Short Circuit Protection

Reverse Polarity Protection

Battery Over Temperature

Cooling System

Approvals


Weight

SBC - 8112 SBC - 8125

Yes

Yes

Fuse Protected

Yes (optional temperature sensor)

Current Controlled Fan

Designed and Manufactured to Comply with CE

214 x 160 x 72mm

8.4 x 6.3 x 2.8in.

1.65kgs (3.6lbs)

255 x 200 x 72mm

10 x 7.9 x 2.8in.

2kgs (4.4lbs)

SBC - 8215

Flood, Sealed (Gel, AGM)

12VDC

60 - 150AH

12VDC

120 - 200AH

24VDC

60 - 150AH

10A Continuous

13.4VDC

Wet-14.4

Sealed-13.9VDC

20A Continuous

13.4VDC

Wet-14.4

Sealed-13.9VDC

10A Continuous

26.8VDC

Wet-28.8

Sealed-27.8VDC

Green - Boost, Off - Float , Red - Battery Over Temperature

100mV

200mVrms

25mV

80%

200 - 250V~ or 90 - 132V~ on request

50Hz - 60Hz

Available in standard CE version / Optional on other version

255 x 200 x 72mm

10 x 7.9 x 2.8in.

2kgs (4.4lbs)



Description

This compact, robust and light weight battery charger gives a complete and fast charge to sealed and wet type of lead acid battery.

In the Bulk Charge Stage, it charges the battery at a constant maximum current until the battery voltage increases to a slightly higher level and switches to the

Absorption Mode at which the battery is then kept at this voltage while the charging current decreases to a low value.

When the battery is fully charged, the charger is then switched to the Float Charge voltage where it can be maintained indefinitely. At the Float Charge Mode, the charger will make up for the loss of self discharge of the battery.

This charger has two selections to cover a wide range of sealed (VRLA) and the wet type of lead acid battery. In addition to the standard short circuit, over Load, over temperature protections, it has electronic reversed polarity protection , output over voltage protection, and battery low voltage protection to prevent damage to the charger and the battery.

3 Stage

Switching Mode Battery Charger

SBC - 2105(5A) 12VDC Series

Features

** 3 Stage (IUOU) Switching Mode Lead Acid Battery

Charger.

** 2 Selectable Bulk Absorption-Float Charge Settings for

Sealed & Wet battery.

** LED indicators for charging and Full /Float mode.

** Wide Input Tolerance for fluctuating mains voltage

** Protections to the charger and battery

Output Short Circuit, Over Load,

Over Temperature, Reverse Polarity.

** Protection to the battery

OVP (Over Voltage Protection) the charger will cut off

output when output voltage is over 15.5V, this gives complete protection the battery.

** Battery Under-Voltage Protection

When voltage of the charged battery is less than 7.5V, the charger will stop charging the battery which may be of wrong rating (6V) or faulty or heavily exhausted.


AC Input Voltage 180-260V, 50Hz~

AC Input Current at full load at 230Vac

SBC - 2105

Yes

0.8A

Output (Charge) Voltage Selections (2 Battery Type)

Sealed Battery - Absorption (13.8V to 14.1V); Float (13.2V to 13.5V)

Yes

Wet Battery - Absorption (14.1V to 14.4V); Float (13.4V to 13.7V)

Maximum Output Charging Current (Continuous)

Line Regulation (180V to 260V) for Charging Current

Ripple and Noise (Peak to Peak)

Yes

5A

0.6%

120mV

84%


Protection

Short Circuit Protected



Over Temperature Protection

OVP (Output Over Voltage Protected

Battery Under Voltage Protection,

Yes

Yes

Yes

Yes

Yes

Yes

when battery voltage <7.5V, charger will stop charging battery

CE Approvals and Standard

Charge Indication

Anodized Aluminum Casing

Size in mm (Width x Height x Depth)

Weight in gm

Included Accessories (Cable, Mounting Clips)

Recommended Battery Capacity Range

Remark

EN 60335 , EN 55014

1 LED, Red : Charging, Green : Full or Float

Yes

142 x 75 x 32mm

380g

Yes

20AH to 50AH

110VAC 60Hz~ Input on Request



3 Stage Lead-Acid Battery Charger with Charger / Power Supply Mode

SBC - 2110(10A) / 2115(15A) / 2120(20A) 12VDC Series

Description

This series of switching mode 3 stage (IUoU) chargers is designed for wet, sealed (RVLA), calcium-calcium, gel in both

SLI (car) and deep cycle type of lead acid batteries.

It has 3 selections of bulk (with absorption) charge and 3 float charge voltage making a total of 9 combinations of charging profile. This is to ensure a safe, fast and complete charge as required by different types of lead acid batteries and applications.

It also has a soft start bulk charge at about 50% of full rated current when battery has been depleted to less than 10.5V open circuit voltage to give a gentle initial charge for deeply exhausted batteries.

The unique selectable Power Supply - Charger Mode provides a nominal 12V DC source (per chosen float voltage) for external load and at the same time not to over charge the battery but keeping the battery fully charged. It is ideal for caravan& other battery back up applications.

With the optional temperature sensor, the charger operates accurately over a wide range of ambient temperature preventing over or under charging the battery.

The 15A and 20A Model SBC-2115/2120 have thermostatically control fan cool., they also have dual output banks for charging two batteries simultaneously.

The streamline, low profile anodized aluminum casing, efficient switching mode circuit design and variable speed fan make it a super quiet and cool running charger and power supply.

In addition to the standard short circuit, over temperature, reverse polarity protections, it has an OVP (output over-voltage protection) to ensure complete protection of your battery and connected load.

Features

** 3 Stage (IUoU) Switching Mode Lead Acid Battery

Charger

** 3 Selectable Bulk Absorption Charge Settings

For Gel ,Wet and Calcium-Calcium lead acid battery.

** 3 Selectable and independent Float Voltage Settings

A total of 9 combinations of adaptive 3 Stage Charging profiles for all types of VRLA (sealed) and Wet lead acid,

SLI (car) and Deep Cycled lead acid battery.

** Battery can be connected to charger indefinitely.

** Automatic Soft Start Bulk Charge for deeply exhausted

battery

To ensure safe and gentle charging of heavily depleted deep cycle battery and car battery.

** Temperature Compensation (with optional remote

sensor )

To prevents over-charging or under-charging battery at high

/ low ambient temperature

** LED indicators for Bulk, Absorption, Float, Fault and

Power-On .

** Dual Banks for simultaneous charging of two batteries.

Two positive charging outputs. Not for 10Amp model.

** Power On Off Switch

This is handy especially in the Power Supply - Charger

Mode.

** Power Supply - Charger Mode

When switched to the Power Supply - Charger Mode, it can be used as constant voltage power supply (according to the selected Float voltage: 13.2/13.5/13.8V) or as a charger

/power supply when connected to a battery and external load in parallel .

** Silent fan cool operation

The thermostatic control variable speed (zero to full speed) does not move at Float Charge or when ambient temperature is lower than 40

°C

** Protections to the charger

Short Circuit, Over Load, Over Temperature, Reversed

Polarity(fused).

** Protection to the battery and load

The OVP protects the load and battery from excessive over- voltage at the charger output.


It operates well from 180V to 260V.




SBC - 2110(10A) / 2115(15A) / 2120(20A) 12VDC Series




Output (Charge) Voltage Selections :

Absorption Voltage for AGM/GEL battery (14.1V to 14.3V)

Absorption Voltage for WET battery (14.6V to 14.8V)

Absorption Voltage for Calcium-Calcium battery (16.2V to 16.4V)

Float Voltage 1 (13.2V)




Soft Start Bulk Charge :

Battery Voltage to Trigger (cut-in) Soft Start Bulk Charge Mode

Soft Start Bulk Charge Current Level (Current Limit)




Selectable Charger / Power Supply Mode (13.2 / 13.5 / 13.8V)

Dual Banks (Outputs) Simultaneously Charging two Batteries

(The two batteries must be of same chemistry, construction & type.)

Protection :



Reverse Polarity Protection (Fused)



Thermostatically Controlled Variable Speed Fan (0 to full speed)

CE Approvals and Standard ( EN 55014 , EN 60335 )

Charge Cycle, Protection Indication :

Separate LED for Bulk, Absorption, Float and Fault Mode

Power ON-OFF LED Indicator

Power ON-OFF Switch

Temperature Sensor Socket

Anodized Aluminum Casing with Mounting Flange


Weight in Kg

Included Accessories (Cable, Spare Fuse)

Optional Accessories (Remote Temperature Sensor)


Remarks

SBC - 2110

Yes

1.2A

Yes

Yes

Yes

Yes

Yes

Yes

10A

<9V

5A

<0.6%

100mV

90%

Yes

No

SBC - 2115

Yes

1.8A

Yes

Yes

Yes

Yes

Yes

Yes

15A

<9V

7.5A

<0.6%

100mV

87%

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Convection Cool

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

160 x 61 x 173mm

1.3kg

Yes

Yes

Yes

Yes

Yes

160 x 61 x 173mm

1.4kg

Yes

Not Included

40AH to 100AH

Yes

Not Included

60AH to 150AH


SBC - 2120

Yes

3A

Yes

Yes

Yes

Yes

Yes

Yes

20A

<9V

10A

<0.6%

150mV

82%

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

160 x 61 x 207mm

1.6kg

Yes

Not Included

80AH to 200AH

3 - STAGE CHARGING DIAGRAM

S.O.C.

BATTERY

STATE OF

CHARGE

BULK CHARGE

CONSTANT CURRENT

ABSORPTION CHARGE

CONSTANT VOLTAGE

CHARGING

VOLTAGE

CHARGING

CURRENT

TIME

FLOATING CHARGE





SBC - 2205(5A) / 2207(7.5A) / 2210(10A) 24VDC Series

Description

This series of switching mode 3 stage (IUoU) chargers is designed for wet, sealed (RVLA), calcium-calcium, gel in both

SLI (car) and deep cycle type of lead acid batteries.

It has 3 selections of bulk (with absorption) charge and 3 float charge voltage making a total of 9 combinations of charging profile. This is to ensure a safe, fast and complete charge as required by different types of lead acid batteries and applications.

It also has a soft start bulk charge at about 50% of full rated current when battery has been depleted to less than 20.5V open circuit voltage to give a gentle initial charge for deeply exhausted batteries.

The unique selectable Power Supply - Charger Mode provides a nominal 24V DC source (per chosen float voltage) for external load and at the same time not to over charge the battery but keeping the battery fully charged. It is ideal for caravan& other battery back up applications.

With the optional temperature sensor, the charger operates accurately over a wide range of ambient temperature preventing over or under charging the battery.

The 7.5A and 10A Model SBC-2207/2210 have thermostatically control fan cool, they also have dual output banks for charging two batteries simultaneously.

The streamline, low profile anodized aluminum casing, efficient switching mode circuit design and variable speed fan make it a super quiet and cool running charger and power supply.

In addition to the standard short circuit, over temperature, reverse polarity protections, it has an OVP (output over-voltage protection) to ensure complete protection of your battery and connected load.

Features

** 3 Stage (IUoU) Switching Mode Lead Acid Battery

Charger

** 3 Selectable Bulk Absorption Charge Settings

For Gel ,Wet and Calcium-Calcium lead acid battery.

** 3 Selectable and independent Float Voltage Settings

A total of 9 combinations of adaptive 3 Stage Charging profiles for all types of VRLA (sealed) and Wet lead acid,

SLI (car) and Deep Cycled lead acid battery.

** Battery can be connected to charger indefinitely.

** Automatic Soft Start Bulk Charge for deeply exhausted

battery

To ensure safe and gentle charging of heavily depleted deep cycle battery and car battery.

** Temperature Compensation (with optional remote

sensor )

To prevents over-charging or under-charging battery at high

/ low ambient temperature

** LED indicators for Bulk, Absorption, Float, Fault and

Power-On .

** Dual Banks for simultaneous charging of two batteries.

Two positive charging outputs. Not for 5Amp model.

** Power On Off Switch

This is handy especially in the Power Supply - Charger

Mode.

** Power Supply - Charger Mode

When switched to the Power Supply - Charger Mode, it can be used as constant voltage power supply (according to the selected Float voltage: 26.4/27.0/27.6V) or as a charger

/power supply when connected to a battery and external load in parallel .

** Silent fan cool operation

The thermostatic control variable speed (zero to full speed) does not move at Float Charge or when ambient temperature is lower than 40

°C

** Protections to the charger

Short Circuit, Over Load, Over Temperature, Reversed

Polarity(fused).

** Protection to the battery and load

The OVP protects the load and battery from excessive over- voltage at the charger output.


It operates well from 180V to 260V.




SBC - 2205(5A) / 2207(7.5A) / 2210(10A) 24VDC Series




Output (Charge) Voltage Selections :

Absorption Voltage for AGM/GEL battery (28.2V to 28.6V)

Absorption Voltage for WET battery (29.2V to 29.6V)

Absorption Voltage for Calcium-Calcium battery (32.4V to 32.7V)





Soft Start Bulk Charge :

Battery Voltage to Trigger (cut-in) Soft Start Bulk Charge Mode

Soft Start Bulk Charge Current Level (Current Limit)




Selectable Charger / Power Supply Mode (26.4 / 27.0 / 27.6V )

Dual Banks (Outputs) Simultaneously Charging two Batteries

(The two batteries must be of same chemistry, construction & type.)

Protection :



Reverse Polarity Protection (Fused)



Thermostatically Controlled Variable Speed Fan (0 to full speed)

CE Approvals and Standard ( EN 55014 , EN 60335 )

Charge Cycle, Protection Indication :

Separate LED for Bulk, Absorption, Float and Fault Mode

Power ON-OFF LED Indicator

Power ON-OFF Switch

Temperature Sensor Socket

Anodized Aluminum Casing with Mounting Flange


Weight in Kg

Included Accessories (Cable, Spare Fuse)

Optional Accessories (Remote Temperature Sensor)


Remarks

SBC - 2205

Yes

1.2A

Yes

Yes

Yes

Yes

Yes

Yes

5A

<20.5V

2.5A

<0.6%

100mV

90%

Yes

No

SBC - 2207

Yes

1.8A

Yes

Yes

Yes

Yes

Yes

Yes

7.5A

<20.5V

3.8A

<0.6%

100mV

87%

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Convection Cool

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

160 x 61 x 173mm

1.3kg

Yes

Yes

Yes

Yes

Yes

160 x 61 x 173mm

1.4kg

Yes

Not Included

20AH to 50AH

Yes

Not Included

30AH to 80AH


SBC - 2210

Yes

3A

Yes

Yes

Yes

Yes

Yes

Yes

10A

<20.5V

5A

<0.6%

150mV

82%

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

160 x 61 x 207mm

1.6kg

Yes

Not Included

40AH to 100AH

3 - STAGE CHARGING DIAGRAM

S.O.C.

BATTERY

STATE OF

CHARGE

CHARGING

VOLTAGE

BULK CHARGE

CONSTANT CURRENT

ABSORPTION CHARGE


CHARGING

CURRENT

TIME

FLOATING CHARGE




13.8VDC

DC-DC Regulated Power Converter

DD - 105 / 107 (Linear mode)

Description

This series of low ripple and noise DC-DC converter are ideal for powering automotive and marine equipment which demands clean and stable regulated DC source.

Features

• 22 - 28V DC input voltage

• 13.8V DC regulated output voltage


• Overload protection

• Over current protection

• Fused

• ON - OFF power switch


• Comes with mounting brackets for either on-dash or under-dash installation


Output Voltage

Continuous Output Current

Maximum Output Current


Load Regulation

Line Regulation

Input Voltage

Efficiency


Indicators

Output Connection Type

Approvals


Weight

DD - 105

13.8VDC

5A

5.5A

3mVrms

0.2V

0.5V

22 - 28VDC

Approx. 57.5%

Over Voltage, Over Current

LED Power

Cable

CE EMC : EN 55014

125 x 47 x 110 mm

4.9 x 1.9 x 4.3 in.

0.6kgs ( 1.3lbs )

DD - 107

7A

8A

125 x 47 x 130 mm

4.9 x 1.9 x 5.1 in.

0.65kgs ( 1.4lbs )



Description

This series of Switching mode DC-DC converters are built to meet the high current applications at 13.8VDC. In addition to the high efficiency, the low profile construction makes use of the heat sinks as main body of the robust, rugged housing of the unit. The OVP (Over voltage protection) protects sensitive electronic equipment.

Output 13.8VDC

Switching Mode DC-DC Converter

SDC - 210 / 225 / 245

Features

• 13.8V DC regulated output voltage

• 22 - 30V DC input voltage


• High power density

• Output over voltage protection



• EMC INTERFERENCE IMMUNITY

• Power on-off switch


SDC - 210

Input Voltage Range

Output Voltage

22 to 30VDC

13.8VDC


8A

SDC - 225 SDC - 245


10A


<200mVp-p

Load Regulation

Line Regulation

500mV

20mV

Efficiency

Input Connection Type


Indicators

Cooling System

88%

Cable

Cable

Power on LED

Natural

20A

25A

50mV

89%

Terminal

Natural

Convection Convection

Overload, Short Circuit


Input Fuse Type

CE Approvals e-Mark Approvals


Standard Car Blade Fuse

EN 55014 , EN 55022 e11 02 1522 e11 02 1524

40A

45A

80mV

88%

Terminal

Variable speed thermally control fan e11 02 1521

125 x 47 x 120mm 156 x 57 x 168mm 156 x 57 x 240mm

4.9 x 1.9 x 4.7in.

6.1 x 2.2 x 6.6in.

6.1 x 2.2 x 9.5in.

Weight

Accessory

0.55kgs (19.4oz.)

Nil

1.4kgs (49.3oz.) 2.2kgs (77.4oz.)

Mounting Bracket Mounting Bracket



Step Up


SDC - 310

Description

This series of DC-DC Switching Mode

Converters are built to meet the high current applications at 28V DC. In addition to the high efficiency, the low profile construction makes use of the heat sinks as main body of the robust, rugged housing of the unit. The OVP ( Over

Voltage Protection ) protects sensitive electronic equipment.

Features


• High power density

• Output over voltage protection

• Short circuit and overload protection



• Power ON - OFF Switch



Output Voltage




Load Regulation

Line Regulation

Output Voltage Protection

Efficiency


Indicators



Cooling System

Input Fuse Type



Weight

Accessory

SDC - 310

10 - 15VDC

28VDC

8A

10A

<100mVp-p

300mV

150mV

Over Voltage Protection

88%

Output Overload, Short Circuit Protection

Power on LED

Cable

One set banana screw on type and one set philips screw type

Natural Convection

Standard Car Blade Fuse

EN 55014 , EN 55022 e11 02 2981

156 x 57 x 130mm (6.1 x 2.2 x 5.1in.)

1kgs (35oz.)

Mounting Bracket



EFFICIENT! COMPACT! COOL!

NEW GENERATION DC-DC CONVERTER

SDC - 5205 / 5208 / 5212

Description

This new generation of SDC- 5200 series of voltage reducers offer regulated 13.8 V DC power from 20-30VDC source such as Land Rovers , commercial vehicles, recreation vehicles, farming equipment and other diesel power vehicles.

The very compact, lightweight and no vent hole casing construction is possible because of the highly efficient, switch mode design with surface mount devices.

Low heat output and low standby current take out the need for an external power on-off switch.

The plastic clip-on mounting system makes the installation easy even in awkward to reach spot. The unit is tamper and dust proof because of no vent holes and no external fuse construction. The PCB component layout is designed and built for vibration loosening resistant, and with moisture proof coating making it ideal for off-road and harsh environments.

The advanced switching mode circuit design results a cool, silent, no humming and no high frequency noise operation. Electronic safeguards and fail-safe feature such as OVP ensure good protection to expensive connected equipments even when there is a fault in the unit.

The 13.8VDC output can be used as a source for float charge for 12V auxiliary battery.

Typical applications for this new generation of DC-DC converters are:

Radio communications, car entertainment such as DVD player, printers, on board computers, security system, GPS, auxiliary lights, spot lights, charging of 12V auxiliary battery, and etc.

Features

• Slim, compact and light construction due to high efficiency & low heat output.

• Dust and tamper proof due to extruded aluminum casing of no vent hole & no external fuse.

• Reliable clip-on mounting bracket construction for easy installation even in hard to get to spot.

• Vibration loosening resistant & coated PCB assembly, ideal for off road vehicles environment.

• Advanced switching mode design & SMT components for high efficiency & cool operation.

• Low standby current takes out the need for an external on-off switch.

• Over Voltage Protection against excessive output voltage in case of wrong installation or fault.

• Auto-reset loss of earth protection.

• Auto-reset over power protection.

• Auto-reset reverse polarity protection.

• Separate LED indicator for operation and fault status.

• Meet e-Mark and CE standards.



Output Voltage


Maximum Output Current at 30% Duty Cycle

No Load Current



Load Regulation

Line Regulation

Efficiency

Protections

Indicators

Input & Output Connection Type

Cooling System

Max. Operating Temperature

Internal Input Fuse (glass type) e-Mark Approval No.

Dimensions (WxHxD) mm inch

Weight

Accessory

SDC - 5205

18V to 38VDC

13.8VDC

5A

7A

<20mA

100mVp-p

SDC - 5208

7A

12A

<30mA

SDC - 5212

12A

16A

<50mA

SDC - 5220

16A

20A

<100mA

10mVrms

80mV

10mVrms

50mV

>89% >90%

OVP (Output Over-Voltage Protection),

15mVrms

>90%

20mVrms

>90%

Loss of Earth Protection Self Reset Protections : a) Reverse Polarity Protection ;

b) Overload Protection ; c) Short Circuit Protection

Green LED - Operate & Red LED - Fault

Push-on Flat Blade Connectors

Natural Convection

-10°C - 50°C

8A 10A e11*72/245*95/54*3079*00

20A 25A

77 x 75 x 32

3 x 3 x 1.3

96 x 75 x 32

3.8 x 3 x 1.3

142 x 75 x 32

5.6 x 3 x 1.3

192 x 75 x 32

7.6 x 3 x 1.3

190g (6.7oz.) 230g (8oz.) 380g (13.4oz.)

Clip-on Mounting Bracket set and Screws, Slip-on Receptacles

480g (16.9oz.)



Regulated Constant Voltage

DC - DC Converter

SDC-8170 (Input 10~16V, Output 13.5V 4.5A cont, 6A max 30min. )

SDC-8270 (Input 20~35V, Output 27V 3A cont, 4A max 30min.)

Description

This series of DC-DC converters is designed to provide a regulated fixed output voltage from un-regulated, fluctuating DC input source.

It provides instantaneous step up and step down voltage conversion to keep the output at a stable, constant output voltage.

With the ever increasing of on- vehicle / boat and on board electronic devices, the supply DC voltage from the battery / alternator system fluctuates with the changing power supply and demand situation.

Many expensive electronic devices such as TFT screens, audio and video equipments, precision instruments have a narrow operating input DC voltage for optimal performance.

This series of regulated, constant voltage DC-DC converters offers a cost effective solution to ensure the optimal performance of your expensive electronic device in a fluctuating DC environment.

The high efficiency advanced switching mode circuit design makes convection cooling possible in a compact aluminum extruded casing.

The totally enclosed plastic end caps and sealed construction make this robust converter moisture, and dust proof. It can withstand the harsh and humid working environment. The plastic clip-on mounting system makes the installation easy even in a hard to reach tight spot.

Features

**

**

**

**

**

**

**

**

**

**

**

**

**

**

Step up and Step down voltage conversion

Regulated stable output voltage

Slim, compact, light aluminum casing

Dust and moisture proof construction

High efficiency switching mode design

Excellent line and load regulation

Low Ripple and Noise

Input under & over voltage protection

Short circuit and over load protection

Over temperature protection

Reverse polarity protection

Loss of earth protection

LED indicators of operation and fault status

Meet E-Mark (CE) standards


Operation Input Voltage Range

Output Voltage

Rated Output Current (Continuous)

Maximum Output Current (30 minutes)

Load Voltage Regulation (0-100%)

Line Voltage Regulation (O/P: 13.5V ; I/P: 10.5-16V)


No Load Current

Efficiency (Input: 13.8V, Output: 13.5V / 4.5A)

Protection :

Short Circuit Protection (self reset)

Input Low Voltage Protection (self reset)

Input High Voltage Protection (self reset)

Reverse Polarity Protection (fused)

Over Temperature Protection (self reset)

Loss of Earth Protection (self reset)

Convection Cooling

Maximum Working Ambient Temperature

Approvals and Standard

LED Indicators (Green=ON ; Red=Fault)

Size in mm (Length x Width x Height)

Weight in gram

Accessories

Remark

SBC - 8170 (13.5Vdc / 4.5A)

10Vdc to 16Vdc

13.5Vdc

4.5A

6.0A

20mV

20mV

<50mV

<150mV

87%

Yes

Yes

Yes

Yes

Yes

Yes

Yes

40°C

SBC-8270 (27Vdc / 3A)

20Vdc to 35Vdc

27Vdc

3.0A

4.0A

20mV

50mV

<60mV

<150mV

89%

Yes

Yes

Yes

Yes

Yes

Yes

Yes

40°C

E-Mark (CE)

Yes mm g

Yes

Clip-on Mounting Bracket set and Screw,

Slip-on Cable Receptacles



Description

This Isolated Ground series provide negative / positive ground reference compatibility, allowing connection of negative ground equipment to positive or floating ground battery system or vice versa. They offer protection level for themselves and to the connected loads. They also offer protection against transient voltages spikes typically encountered on electric fork lifts. Being switch mode, they have high efficiency (>80%), produces little heat and are of small size for the power they deliver.

13.8VDC Isolated Ground


SSDC - 210 / 240

Features

• Negative or positive ground reference


• Low profile , high power density

• Protection against transient voltages


• 22 - 30VDC input voltage


• Over current protection




Output Voltage

SSDC - 210

22 to 30VDC

13.8VDC


8A


10A


<100mVp-p

Load Regulation

350mV

Line Regulation

20mV

Efficiency



Indicators

Cooling System




Weight

Accessory

250mV

50mV

>80% >86%

Cable

Cable

Power on LED

Terminal

Natural Convection Variable speed thermally control fan

Over Voltage, Overload, Short Circuit

EN 55011 , EN 55022 EN 55022 e11 02 1520

125 x 47 x 120mm

4.9 x 1.9 x 4.7inch

0.65kgs (1.4lbs )

Nil

SSDC - 225

35A

40A

Nil

156 x 57 x 240mm

6.1 x 2.2 x 9.5in.

2.2kgs (5bs )

Mounting Bracket



SOLAR

Combo Inverter

MEM - 1115

Description

This Solar Compo Inverter series have inverter and PV charge controller in one unit.

With the benefits of fewer components and wiring connections the compo unit is cost effective and reliable .

The self contained unit is user friendly with easy hook up connection to the PV panel and battery.

There are 3 separate LED indicators to show the battery's state of charge: Low, Medium, High; one LED to show operation of the Solar charge controller and a bi-color

LED for the operation status of the modified sine wave inverter.

The built in PV charge controller utilizes PWM charging technology to ensure fast and efficient charging and effective protection against over-charging the battery.

Reverse Polarity Protection for PV terminal is an added protection for the costly PV panel.

The efficient inverter has 300W surge capability for powering up difficult loads with high start up current, protections such as short circuit, overload, overtemperature, and low battery cut-off are standard. Power on-off switch allows for better conservation of battery's power. The anodized aluminum casing ensures efficient cooling and better corrosion resistant.

Features

• Compact, cost effective user friendly simple hook up

Reverse polarity protection for Solar modules and inverter

• 3 separate LED Battery Level indicators.

• Low battery, short circuit, overload and over temperature protections.

• Recoverable AC Fuse

• Car Blade DC fuse


MEM - 1115

PV Module Input (Charge Controller)

Continuous Charging Current

Max. Charging Current for 5 minutes

Battery System

Maximum PV Panel Open Circuit Voltage

PV Module Operation Indication

Electronic Blocking Protection


Transient Voltage Protection

Battery Connections

Battery Overcharge Protection

PWM Set-point

Battery Reverse Polarity Protection

Battery Level Indication

Battery Over-Discharge Protection

230VAC Output (Inverter)

Rated Output Voltage

Rated Output Power

Maximum Surge Power

Waveform

Efficiency

Cooling Method

Inverter Operation Indication

Inverter On/Off Control

Protections

Fuses


Construction


Weight

8Amp

10Amp

Battery Voltage : 12VDC ; Battery Type : Sealed (Factory Preset) or Wet

26VDC

LED to Show PV in Operation

Block Feedback Current to PV from Battery

To Prevent PV Module and Battery accidental reverse

Yes

Yes by Pulse Width Modulation

Sealed - 14.3VDC (Factory Preset) , Wet - 14.8VDC

Yes by Car blade fuse & diode

3 LED : High , Medium , Low

Yes Inverter be shut down at 10.5VDC

230VAC , 50Hz~

Continuous 150Watts

300Watts

Modified Sine Wave

>80% @ Rate Power pf=1

Natural Cooling

Bi-Color LED Showing On (Green) or Shut Down (Red)

Power On/Off Switch

Short Circuit, Overload, Over Temperature

Recoverable AC Fuse & Car Blade DC Fuse

-5 to +50°C

Anodized aluminum casing with mounting brackets,

PCB with conformal coating

Approx. 220 x 93 x 70mm (8.7 x 3.7 x 2.8in.)

Approx. 850g (30oz.)



Air - Car

75W Notebook DC-AC Inverter

MEM - 2101

Works without risk of Lithium Ion Battery

Power Your Notebook with or WITHOUT the Lithium Ion Battery

Slim , Light , Compact

Comes with Airline-Car Power Adapter Plugs

Designed for use with Notebook and Digital Portables

Enhanced Protection Circuits

Applications

Suitable for all major brand

Notebook computers , digital portable like video camcorder , digital camera ,

DVD player and etc.

Features & Benefits

Plugs directly into airline's in-seat power receptacle ( 1st class and B class )

Plugs directly into your car's cigarette lighter

Automatic Shutdown prevents your car's battery from excessive draining

Dual Status LED indicator , Green for in operation , Red for shutdown

Enhanced Protection Circuit

Output Short Circuit Protection

High Temperature (thermal) shutdown

Overload shutdown

Over voltage shutdown

Undervoltage shutdown

Each of the above is a MUST for the safety of the user and protection of you notebook and its power input source


Input Voltage Range : 11 ~ 15VDC

Output Rated Power : 75W Continuous , 90W Maximum

Output Voltage & Frequency : 230VAC 50Hz / 120VAC 60Hz On Request

Indicator : Dual color LED ( Green~operation , Red~shutdown )

Protections : Short Circuit , Overload , Low Battery Voltage , Over Battery Voltage

Approvals : E Mark ( e11 02 1625 ), FCC PART15 Class B

Dimension (LxWxH) : 114 x 76 x 36 mm ( 4.5 x 3 x 1.4 in. )

Total Weight : 310g ( 11oz. )



Pure Sine Wave

500W 12/24VDC Double Insulated Power Inverter

ME - 4105 / 4205

Description

These series of pure sine wave inverter is designed and manufactured with double insulation safety standard as required by the latest CE directives.

The informative 5 stage and 3 color LED indicator for load level and the battery state will tell the user : a. how much spare capacity left in the inverter b. is the wiring connection to battery in good order and properly sized c. the loading condition during start up and continuous running of the load d. the state of charge of battery (how much juice left) during use .

and more ………

Diagnosis with the fault light, the load and battery indicators , you can ensure proper use of the inverter with appropriate load and right size battery for your application .

No more surprises , No more let down at the most critical moment to find out that your battery can no longer power your inverter and appliance.

Features

• Double Insulation Safety Standard

• 5 level 3 color LED indicator for Battery State

• 5 level 3 color LED indicator for Load condition

• Manual select Standby mode for energy saving

• Comprehensive built in protections


Input Voltage

Output Voltage

Output Voltage Frequency

Rated Output Power

Maximum Surge Power

Output Waveform

Total Harmonic Distortion

Efficiency

No Load Input Current (Standby On)

No Load Input Current (Standby Off)

Full Load Input Current

Inverter Operation Indication

Inverter ON/OFF Control

Cooling Method

Protections

Approvals

Fuse



Weight

MEM - 4105

10 - 16VDC

230V AC / 50Hz~

50Hz~

500W

650W

MEM - 4205

20 - 32VDC

Pure Sine Wave

<3%

>80%

<0.6A

<1A

52A

<0.3A

<0.6A

24.8A

Battery 5 Levels & 3 Color LED Indication,

Load 5 Levels & 3 Color LED Indication,

Fault Red LED Indication

Power ON/OFF Switch at Front, Standby ON/OFF Switch at Rear


Input Under & Over Voltage Protection, Overload Protection,

Output Short Circuit Protection, Over Temperature Protection

CE EMC : EN 55022 , LVD : EN 61558

3 Internal Fuse each of 25A / 230V Glass Fuse

0 - 40°C

250 x 140 x 102mm (9.8 x 5.5 x 4inch)

3kgs (6.6lbs)



PV

Charge Controller

SBC - 2106 / SBC - 2106L

Description

This series of low powered and cost effective PV Charge Controller is designed for trouble free application in remote high humid environment .

The whole unit is potted in Epoxy Resin . It is suitable for seal or wet type lead acid battery and all types of PV modules. The full solid state electronic components using 0 to 100% Pulse Width Modulation charging and power switching by MOSFET assures optimal utilization of sunlight and safe charging of battery .

Selection for charging sealed or wet type of battery is made possible by shorting of terminal wire. The

SBC-2106L is made with Night Light Load DC output .

Features

• Compact size

• Water resistant

• Simple to use

• Electronic Blocking of reverse current to PV module

• Sealed and Wet type battery connection.

• Night Light Mode DC output for L version


Model

Battery System Voltage

Max. PV Open Circuit Voltage

Max. PV Short Circuit Current

PWM Setpoint

SBC-2106

12VDC

26VDC

6A

SBC-2106L

Min. Operating Voltage

Rated Charging Current

Max. Charging Current (5min.)

Rated Load Current

Max. Load Current (1min.) 8A

PV Voltage While Load Turn ON SBC-2106 does not

PV Voltage While Load Turn OFF

Low Battery Shutdown for Load

Low Battery Recover for Load

Ambient Temperature Range

Sealed Type Battery Setting : 14.3V ±0.1V

Wet Type Battery Setting : 14.8V ±0.1V

3VDC

6A

8A

6A have load terminals

SBC-2106 does not have load terminals

-40 ~ +60°C

≤3.5V

≥5 ±0.2V

≤10.5 ±0.2V

≥11.8 ±0.2V

Relative Humidity

Approvals

Dimension (LxWxH)

Weight

100%

EN 55022 / EN 61001,

FCC PART 15 SUBPART B CLASS B

97 x 46 x 25.5 mm

103g



PV


SBC - 6108 / 6112 / 6120

Description

The SBC-6100 Series PV charge controller is designed for use with all types of photovoltaic panels and wet or sealed lead acid batteries.

The MCU (Microprocessor controller) is programmed with 3stage charging algorithms and with 0~100% PWM (Pulse width

Modulation) duty cycles to provide the fastest, optimal charging current and voltages from PV panels according to the actual state of charge and type of battery.

The 3-stage (Bulk, Absorption, Float) and *Equalization* charging cycles ensure complete charging cycles and maintenance of lead acid battery automatically. *Equalization* Charging is only for Wet type lead acid battery, automatically cycles once a month for 2 hours.

Equalization Charging can be de-activated or re-activated manually.

Electronic Blocking of back current to PV and overcharging battery protection are standard.

Features

• Microprocessor control PWM and 3 stage charging algorithms.

Bulk , Absorption & Float Charge LED indications.

• 5 State LED Indications of battery levels.

• Electronic Overcharge Protection & back current blocking to

PV panel.

• Over temperature Protection of PV Charge Controller's electronic circuit.

• Dusk to Dawn automatic ON-Off with 10 selectable on-off programs.

• Optional Temperature Sensor for compensated battery charging.

• Optional Remote Signal Terminal.

DC Output (for small DC load)

The DC output terminal has many value added night-light mode program , please see user manual at our website for detail description.

The DC output has dusk to dawn automatic on-off operations.

There are 10 selectable multiple on-off programs, each with different power-on durations for various needs or lighting schedules.

Optional Accessories

1. There is an optional Remote Signal Terminal which can:

A. This signal is synchronized with the DC output status. It controls the ON/OFF operation of equipment such as inverter hooked up to the battery bank to operate along with the nightlight mode program and share the safeguard function such as low battery disconnect and reconnect.

B. It makes extension connection of the battery status LED to allow remote monitoring Battery bank status.

2. Temperature sensor ( 1.8m wire length) for correct bulk and float charging voltages according to the temperature at the battery.


Battery Voltage


Continuous Load / Charge Current

Maximum Charge Current (5 min.)

Maximum Load Current (5 min.)

SBC - 6108

12VDC

26VDC

8A

10A

10A

Operation Current (no load and no PV)

Voltage Across Terminal (PV to Battery)

Voltage Across Terminal (Battery to Load)

Electronic Blocking

30mA

0.6V

0.3V

Yes

(To protect against reverse polarity connection of PV panel and

SBC - 6112

12A

15A

20A

0.6V

0.3V

to block current from battery to PV panel when voltage of battery is higher than PV panel)


Yes

Over Charge & Over-Discharge Protection

Battery Status LED Indication

Yes

5 State LED Indications

Charging Status LED Indication

Recommended Wire Size


#12AWG


Weight

Fuse

Operating Ambient Temperature


Battery Charging Float Voltage Setting

Battery Charging Bulk Voltage Setting

DC Load Control Mode (for DC load terminal):

Low Voltage Disconnect (LVD)

Low Voltage Reconnect (LVR)

150 x 85 x 45mm (5.9 x 3.3 x 1.8inch)

440g (15.5oz.)

15A

-10 to 50˚C

20A

Yes

Factory Preset 13.4VDC




SBC - 6120

20A

25A

25A

0.8V

0.4V

30A



Description

The SBC-6200 Series PV charge controller is designed for use with all types of photovoltaic panels and wet or sealed lead acid batteries.

The MCU (Microprocessor controller) is programmed with 3stage charging algorithms and with 0~100% PWM (Pulse width

Modulation) duty cycles to provide the fastest, optimal charging current and voltages from PV panels according to the actual state of charge and type of battery.

The 3-stage (Bulk, Absorption, Float) and *Equalization* charging cycles ensure complete charging cycles and maintenance of lead acid battery automatically. *Equalization* Charging is only for Wet type lead acid battery, automatically cycles once a month for 2 hours.



Features


Bulk , Absorption & Float Charge LED indications.


• Electronic Overcharge Protection & back current blocking to

PV panel.

• Over temperature Protection of PV Charge Controller's electronic circuit.





Battery Voltage





SBC - 6208

24VDC

52VDC

8A

10A

10A





30mA

0.8V

0.5V

Yes

(To protect against reverse polarity connection of PV panel and

SBC - 6212

12A

15A

20A

0.6V

0.3V

to block current from battery to PV panel when voltage of battery is higher than PV panel)


Yes



Yes


Charging Status LED Indication



#12AWG


Weight

Fuse








150 x 85 x 45mm (5.9 x 3.3 x 1.8inch)

0.44kgs (0.2lbs)

15A

-10 to 50˚C

20A

Yes



Factory Preset 23VDC


PV


SBC - 6208 / 6212 / 6220


The DC output terminal has many value added night-light mode program , please see user manual at our website for detail description.





A. This signal is synchronized with the DC output status. It controls the ON/OFF operation of equipment such as inverter hooked up to the battery bank to operate along with the nightlight mode program and share the safeguard function such as low battery disconnect and reconnect.

B. It makes extension connection of the battery status LED to allow remote monitoring Battery bank status.

2. Temperature sensor ( 1.8m wire length) for correct bulk and float charging voltages according to the temperature at the battery.

SBC - 6220

20A

25A

25A

0.8V

0.4V

30A



PV


SBC - 7108 / 7112 / 7120

Description

The SBC-7100 Series PV charge controller is designed for use with all types of photovoltaic panels and different types of batteries, such as wet or sealed lead acid, lead calcium, lead antimony battery, NiCad or NiFe alkaline battery.

The MCU (Microprocessor controller) is programmed with 3 stage charging algorithms and with 0~100% PWM (Pulse Width Modulation) duty cycles to provide the fastest, optimal charging current and voltages from PV panels according to the actual state of charge and type of battery.

The 3-stage (Bulk, Absorption, Float) and *Equalization* charging cycles ensure complete charging cycles and maintenance of lead acid battery automatically.

Bulk and Float threshold charge voltage levels are user adjustable to meet specific battery manufacturer's recommendation.

*Equalization Charging is only for Wet type lead acid Battery, automatically cycles once a month for 2 hours.


Hence, maximum PV charging efficiency and longer the service life span of the battery are ensured.

Ampere Hour logging read outs in three sets, today and last two days are shown on the LCD. This is useful to check the condition of PV data for efficiency and actual capacity of your system.




A. This signal is synchronized with the DC output status. It controls the ON/OFF operation of equipment such as inverter hooked up to the battery bank to operate along with the night-light mode program and share the safeguard function such as low battery disconnect and reconnect.

B. It makes extension connection of the battery status LED to allow remote monitoring battery bank status.

2.Temperature sensor (1.8m wire length) for the compensated bulk and float charging voltages according to the temperature at the battery.


The DC output terminal has many value added night-light mode programs , please see user manual at our website for detail descriptions.



The battery low voltage level disconnect and reconnect settings are user adjustable.

Features

• User adjustable charging voltages

• Suitable for most types of heavy duty 12V battery.


• Bulk, Absorption & Float Charge status on LCD Display.

• Ampere Hour logging read outs in 3 sets, today and last 2 days.


• Electronic Overcharge Protection & Back Current Blocking to PV panel.

• Over Temperature Protection of PV Charge Controller's electronic circuit.


• Adjustable battery low voltage level disconnect and reconnect for DC output.



U er

C harg

Adju t ing

V olta g e es


Battery Voltage









SBC - 7108

12VDC

26VDC

8A

10A

10A

30mA

0.6V

0.3V

Yes

SBC - 7112

12A

15A

20A

0.6V

0.3V

(To protect against reverse polarity connection of PV panel and to block current from battery to PV panel when voltage of battery is higher than PV panel)



Yes

Yes


Charging Status LCD Indication


3 State LCD Display (Bulk, Absorb, Float)



Weight

Fuse








#12AWG

150 x 85 x 45mm (5.9 x 3.3 x 1.8inch)

470g (16.5oz.)

15A

-10 to 50˚C

Factory Preset 8 - 16VDC


20A

Yes



SBC - 7120

20A

25A

25A

0.8V

0.4V

30A



Description

The SBC-7200 Series PV charge controller is designed for use with all types of photovoltaic panels and different types of batteries, such as wet or sealed lead acid, lead calcium, lead antimony battery, NiCad or NiFe alkaline battery.

The MCU (Microprocessor controller) is programmed with 3 stage charging algorithms and with 0~100% PWM (Pulse Width Modulation) duty cycles to provide the fastest, optimal charging current and voltages from PV panels according to the actual state of charge and type of battery.

The 3-stage (Bulk, Absorption, Float) and *Equalization* charging cycles ensure complete charging cycles and maintenance of lead acid battery automatically.

Bulk and Float threshold charge voltage levels are user adjustable to meet specific battery manufacturer's recommendation.

*Equalization Charging is only for Wet type lead acid Battery, automatically cycles once a month for 2 hours.


Hence, maximum PV charging efficiency and longer the service life span of the battery are ensured.

Ampere Hour logging read outs in three sets, today and last two days are shown on the LCD. This is useful to check the condition of PV data for efficiency and actual capacity of your system.




A. This signal is synchronized with the DC output status. It controls the ON/OFF operation of equipment such as inverter hooked up to the battery bank to operate along with the night-light mode program and share the safeguard function such as low battery disconnect and reconnect.

B. It makes extension connection of the battery status LED to allow remote monitoring battery bank status.

2.Temperature sensor (1.8m wire length) for the compensated bulk and float charging voltages according to the temperature at the battery.


Battery Voltage




Maximumu Load Current (5 min.)





SBC - 7208

24VDC

52VDC

8A

10A

10A

10mA

0.8V

0.5V

Yes

SBC - 7212

12A

15A

20A

0.6V

0.3V

(To protect against reverse polarity connection of PV panel and to block current from battery to PV panel when voltage of battery is higher than PV panel)



Yes

Yes


Charging Status LCD Indication


3 State LCD Display (Bulk, Absorb, Float)



Weight

Fuse








#12AWG

150 x 85 x 45mm (5.9 x 3.3 x 1.8inch)

47g (0.2lbs)

15A

-10 to 50˚C

Yes



20A



PV


SBC - 7208 / 7212 / 7220


The DC output terminal has many value added night-light mode programs , please see user manual at our website for detail descriptions.



The battery low voltage level disconnect and reconnect settings are user adjustable.

Features

• User adjustable charging voltages

• Suitable for most types of heavy duty 24V battery.


• Bulk, Absorption & Float Charge status on LCD Display.

• Ampere Hour logging read outs in 3 sets, today and last 2 days.


• Electronic Overcharge Protection & Back Current Blocking to PV panel.

• Over Temperature Protection of PV Charge Controller's electronic circuit.


• Adjustable battery low voltage level disconnect and reconnect for DC output.



U er

C harg

Adju t ing

V olta g e es

SBC - 7220

20A

25A

25A

0.8V

0.5V

30A



Car Power Adaptor

Regulated Switching Mode DC-DC Adaptor

SDC - 2010

ANOTHER ENERGY CONSERVATION PRODUCT

WASTE LESS BATTERY HELP TO SAVE THE EARTH AND YOUR MONEY

Description

A high tech efficient car power adapter built to provide stable clean DC power for the voltage sensitive electronic digital equipment with minimal strain on the car's electrical power source.

Application

CD players, cassette recorders, radios, electronic games such as game boy, portable DVD players, LCD

TV, digital cameras, camcorders, speed check scanners, map reading lights, and etc.

Safety Features & Approvals


• Automatic thermal cut off

• Automatic overload cut off

• 2.0 Amp safety fuse

• CE Approval (EMC 55014)

• e-Mark Approval ( e11 02 1523 )

Features

• IC regulated switching mode DC converter

• 82% efficiency resulting cool running and less strain on car's electrical power source

• 11 - 30 VDC input voltages suitable for most truck and car

• 7 selectable regulated output voltages

• Quality 1,500mA available for the full range of regulated output voltages

• 7 sets of detachable plugs (polarity reversible) suitable for most portables

• LED power indicator

Input Voltage

: 11 to 30VDC (Negative earth)

Regulated output voltages

: Regulated at 1.5V, 3V, 4.5V, 6V, 7.5V, 9V and 12V

(12V is regulated only when input voltage is higher than 16V)

Maximum output current

: 1800 mA

Continuous output voltages : 1500 mA

Efficiency

Indicator

: 82%

: LED Power-On Indicator

Casing material

Size and Net weight

Lead wire

Accessory

Approvals

: Fire Retardant Poly-carbonate with soft resilient coating

: Length 100mm. Width 40mm. ; 100g

: 1.5M

: 7 pieces of the most commonly used plugs.

: e-Mark : e11 02 1523 , CE : EMC EN 55014



Digital Car Power Adaptor with LCD & Battery Guard

SDC - 5203

• POWER TO PERFECTION • SAFETY BEYOND STYLE •

Description

This sleek robust high current car power adapter offers a range of precise and clean DC outputs for most electronic, digital portables and power hungry PMP (Portable Multi-media Player) such as DVD player.

The microprocessor control (MCU) design provides accurate digital read outs of the vehicle's battery voltage, dynamic output load condition and selected output voltage.

The battery is protected from over-discharge by automatic low voltage cut off ( battery power to load) and a warning buzzer to alert users .

User can select the back light color in the large LCD indicator at will to match the decor of the dash board to his or her taste.

One 5V 500mA USB port and a 3Amp selectable DC voltage output with several detachable plugs fit for most portables.

Protections

• Short circuit & overload protection

By current limiting for both 3A and USB output

• Thermal protection

5 amp fuse in cigarette plug.

• Low Battery Voltage Disconnect to protect battery from over-

discharge

This is an important function to prevent your car from stranding with a flat battery.

When the MCU of the unit detects the battery voltage is at critically low level, it will give both visual and audio warning and cuts all power to both 3A and USB outputs to stop further draining of battery power.

• Over voltage (output) Protection

This is to protect voltage-sensitive devices connected to the adapter.

When the MCU of the unit detects the battery voltage is at critically high level, it will give both visual and audio warning and cuts all power to both 3A and USB outputs.

Features

• Microprocessor Control and Switching Mode designed Universal input (12V and 24 V battery system) for car and lorry.

• Large illuminated LCD display :

Accurately shows battery voltage,

Shows the selected output voltage

Shows how much current the load is drawing out of the 3 Amp adapter.

• Digital selection of regulated output voltage including a 5V.

• (8 selections for 24V system and 7 selections for 12V system.)

• Automatic low battery voltage cut-off to protect battery from over discharge.

• Output over voltage cut off to protect voltage sensitive connected devices.

• Choice of 5 user selectable back- light colors

• Output short circuit and overload protection

• High temperature protection

• Input fuse protection

Construction

• Anodized Aluminum alloy casing in standard color charcoal black.

• Measurement : 98mm x 57mm x17mm

• Net Weight of unit without accessories : 100gm.

• 80 mm X 16mm LCD display with 5 user selectable back light color

** Digital read out of battery voltage and L, N, H icons ;

12V system 24V system

L indicates

N indicates battery voltage

< 11.5 V

11.5 ~13.0V

<23.0 V

23.0~26.0V

>26.0V

H indicates battery voltage > 13.0V

** Digital read out of selected output voltage

** Easy to spot bar chart , one bar = 500mA load.


• Input DC voltage range :

12V and 24V battery system.

• Output regulated DC voltage selections :

1.5/ 3 / 4.5/ 5 / 6 / 7.5 /9 / 12V* dc

(12V regulated output is only for 24V battery system.)

• Dual outputs :

One DC Output, max. current 3,000 mA

One USB Port, max. current 500 mA.

• The 3A DC output and the USB port can operate

simultaneously.

Accessories

Standard Accessories

A. Input cable (1.5M) with cigarette plug.

B. Output cable (1.5 M)

C. 7 common DC plugs (polarity reversible)

D. One set of dual lock sticker tapes.

E. One spare 5A fuse

F. One pouch for keeping all the accessories.


USB cable and 5 charge plugs for 5 popular cell phones.

Application

DVD player, i-Pod#, SONY PSP#, All portables with USB link cable for charge or power, all Portable Multi-media players with 3A max. load, GPS, handheld telecom.

Remarks : i-Pod#, SONY PSP# are registered trade marks and brands names of corresponding corporations.



No results