- No category
advertisement
Installations/Connections
Caution:
• FOR UL LISTED MODEL(S), ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY.
This camera is designed to be installed on a ceiling.
Before starting the installation/connection, prepare the required devices and cables.
Before starting the connection, turn off the power of the devices including the camera and the PC or disconnect from the
12 V DC power supply.
Install
When installing the camera on a ceiling, there are two methods; wiring through a hole in the ceiling (☞ page 16) and wiring through a cable guide (unnecessary to make a hole in the ceiling) (☞ page 20).
Important:
• Procure 4 screws (M4 or M6) to secure the camera mount bracket (accessory) to the ceiling according to the material of the installation area. In this case, wood screws and nails should not be used.
When installing on concrete ceiling: Fix with anchor bolts (M6).
(Recommended tightening torque: M4: 1.6 N·m {1.18 lbf·ft}, M6: 5.0 N·m {3.69 lbf·ft})
• Required pull-out capacity of a single screw/bolt is 196 N {19.99 lbf} or more.
• If a ceiling board such as plaster board is too weak to support the total weight, the area shall be sufficiently reinforced or the ceiling mount bracket for the camera WV-Q105 (option), or the ceiling embedding bracket WV-Q155S/
WV-Q155C (option), shall be used.
• When using an outdoor housing to install the product on the ceiling, use the inner cover (provided with WV-Q157 or other optional mount brackets). That can avoid the shape of the camera from reflecting on images.
• When using a mount bracket (option) or inner cover (provided with WV-Q157 or other optional mount brackets), refer to the operating instructions of the bracket in use.
• Remove the cover film from the transparent part of the dome cover after the installation is complete.
• Be sure to install the safety wire to prevent a fall of the camera resulting in injury or accidents in case the mount bracket (accessory) comes off. (Only for models that can be installed with a safety wire)
<When using the optional mount bracket WV-Q105>
Anchor bolt
(Procured locally)
Roof space
WV-Q105 (option)
Safety wire angle
Mounting screws
(4 pcs, WV-Q105 supplied)
Ceiling board such as plaster board
Safety wire
WV-SC385
Decorative cover (accessory)
Camera mount bracket
(accessory)
Camera
15
16
Wire through a hole in the ceiling
Step 1
Fix the camera mount bracket (accessory) with four optional fixing screws (M4 or M6, option).
There should be no obstacles such as wall in a range of
100 mm {3-15/16 inches} away from the center point of the camera mount bracket.
Shooting direction (FRONT)
83.5 mm
{3-9/32 inches}
Step 3
Insert the SDHC/SD memory card into the SDHC/SD memory card slot. Refer to page 26 for how to insert the
SDHC/SD memory card.
Step 4
Attach the safety wire fixed with the camera mount bracket (accessory) to the camera.
After attaching the safety wire to the camera, confirm that the ring part at the end of the safety wire is securely hooked on the safety wire holder.
Screw
(M4)
FRONT
Safety wire
LOCK
OPEN
110 mm
{4-5/16 inches}
100 mm {3-15/16 inches} or more away from obstacles such as wall
Screw
(M6)
Step 2
Make a hole in the ceiling to pass the cables through.
Make a hole 25 mm {31/32 inches} in diameter. The center point of the hole should be located approx. 75 mm
{2-15/16 inches} away from the center point of the camera mount bracket.
LOCK
OPEN
Wiring hole
(ø25 mm {31/32 inches})
75 mm
{2-15/16 inches}
FRONT
Safety wire holder
Step 5
Connect cables to the External I/O terminals, microphone/ line input connector, audio output connector and the monitor out connector for adjustment. When connecting these cables, hold the base part of the camera.
Base part
Microphone/line input connector
External I/O terminals
LINK
10BASE-T/
100BASE-TX
ACT INITIAL
SET
POWER
Audio output connector
Monitor out connector for adjustment
EXT I/O
MIC/LINE IN AUDIO OUT MONITOR OUT
12V IN
4 3 2 1
• External I/O terminals
Connect external devices.
When connecting an external device, remove 9 mm -
10 mm {11/32 inches - 13/32 inches} of the outer jacket of the cable and twist the cable core to prevent the short circuit first.
Specification of cable (wire): AWG #22 - #28, Single core, twisted
Strip range
EXT I/O terminal 2
(ALARM IN2/ALARM OUT)
Approx. 9 mm - 10 mm
{11/32 inches - 13/32 inches}
EXT I/O terminal 1
(ALARM IN1)
4 3 2 1
GND
EXT I/O terminal 3
(ALARM IN3/AUX OUT (Auxiliary output))
Important:
• Do not connect 2 wires or more directly to a terminal.
When it is necessary to connect 2 or more wires, use a splitter.
• Input and output of the external I/O terminal 2 and 3 can be switched by configuring the setting. Refer to the Operating Instructions (PDF) for further information about the EXT I/O terminal 2 and 3 (ALARM IN2, 3) settings ("Off", "Alarm input", "Alarm output" or "AUX output").
• The default of EXT I/O terminals is "Off". When "Off" is selected, it is possible to connect external devices as well as the input setting.
• When using the EXT I/O terminals as the output terminals, ensure they do not cause signal collision with external signals.
<Ratings>
• ALARM IN1, ALARM IN2, ALARM IN3
Input specification: No-voltage make contact input
(4 V - 5 V DC, internally pulled up)
OFF: Open or 4 V - 5 V DC
ON: Make contact with GND (required drive current:
1 mA or more)
• ALARM OUT, AUX OUT
Output specification: Open collector output (maximum applied voltage: 20 V DC)
Open: 4 V - 5 V DC by internal pull-up
Close: Output voltage 1 V DC or less (maximum drive current: 50 mA)
• Microphone/line input connector
Connect a monaural mini plug (ø3.5 mm).
• Input impedance: Approx. 2 kΩ
• Recommended cable length: 1 m {3.28 feet} or less
(for microphone input)
10 m {32.8 feet} or less (for line input)
• Recommended microphone: Plug-in power type
(option)
• Supply voltage: 2.5 V ±0.5 V
• Recommended sensitivity of microphone: –48 dB ±3 dB (0 dB=1 V/Pa,1 kHz)
• Recommended plug: L type
Important:
• Connect/disconnect the audio cables and turn on the power of the camera after turning off the power of the audio output devices. Otherwise, loud noise may be heard from the speaker.
• Audio output connector
Connect a stereo mini plug (ø3.5 mm) (Audio output is monaural.). Use an external powered speaker.
• Recommended cable length: 10 m {32.8 feet} or less
• Recommended plug: L type (A straight type plug must be 40 mm {1-9/16 inches} or less.)
• Monitor out connector for adjustment
Connect a monaural mini plug (ø3.5 mm) (only for checking if images are displayed on the monitor).
• Recommended plug: Straight type (Because of the pin array difference, it is difficult to fit an L type plug into this connector.)
Important:
• The monitor out connector for adjustment is provided only for checking the adjustment of the angular field of view on the video monitor when installing the camera or when servicing.
It is not provided for recording/monitoring use.
• Black bands may appear at the top and bottom or right and left of the screen. (That does not affect the adjustment because the angular field of view is not changed.)
Step 6
Mount the camera onto the camera mount bracket
(accessory). Fit the lock plate of the camera onto the guide part of the camera mount bracket, and rotate the camera clockwise after inserting the camera while putting the center of the camera (screw hole for a tripod) onto the center of the camera mount bracket.
17
18
Guide part
Lock plate
20 °
Rotate
Camera
Center of the camera mount bracket
Moving part
LOCK
OPEN
FRONT
Base part
Camera mount bracket
(accessory)
Step 8
Connect the cables to the network connector and the power inlet.
Important:
• When the power of the camera is turned on, the camera will start panning and the position will automatically be initialized.
• Do not touch the camera in the process of initialization. Otherwise, it may fail to initialize and may cause malfunction.
• When the camera has been inadvertently touched and moved after the initialization is complete, the preset positions may be inaccurate. In this case, use the position refresh function or restart the camera to correct the preset positions.
Refer to the Operating Instructions (PDF) for further information.
Network connector
12 V DC power supply terminal
LINK
10BASE-T/
100BASE-TX
ACT
INITIAL
SET
POWER
EXT I/O
MIC/LINE IN AUDIO OUT MONITOR OUT
12V IN
4 3 2 1
Important:
• When mounting the camera onto the camera mount bracket, hold the base part of the camera. Mounting the camera while holding the moving part may result in malfunction.
Step 7
Fix the camera on the camera mount bracket (accessory) using the camera fixing screw (accessory).
Recommended tightening torque: 0.68 N·m
{0.50 lbf·ft}
Fixing screw
(accessory)
• Network connector
Connect a LAN cable (category 5 or better, STP*) to the network connector.
* PAL model only
Important:
• Use all 4 pairs (8 pins) of the LAN cable.
• The maximum cable length is 100 m {328 feet}.
• Make sure that the PoE device in use is compliant with IEEE802.3af standard.
• When connecting both the 12 V DC power supply and the PoE device for power supply, 12 V DC will be used for power supply.
• When the LAN cable is disconnected once, reconnect the cable after around 2 seconds. When the cable is quickly reconnected, the power may not be supplied from the PoE device.
• 12 V DC power supply terminal
q Loosen the screw of the power cable plug (accessory).
w Connect the output cable to the power cable plug.
Strip 3 mm to 7 mm {1/8 inches to 9/32 inches} from the end of the wire, and twist the stripped part of the wire sufficiently to avoid short circuit.
Specification of cable (wire): 16 AWG - 24 AWG,
Single core, twisted
* Check whether the stripped part of the wire is not exposed and is securely connected.
e Tighten the screw of the power cable plug.
r Connect the power cable plug to the 12 V DC power supply terminal on the rear of the camera.
* FOR UL LISTED MODEL(S), ONLY CONNECT 12 V
DC CLASS 2 POWER SUPPLY.
Strip range
Step 9
After completing the cable connections, attach the decorative cover (accessory).
q Align the indication "OPEN" of the decorative cover to the decorative cover guide of the camera mount bracket.
Decorative cover guide
LOCK
OPEN
Approx. 3 mm - 7 mm
{1/8 inches - 9/32 inches}
WV-SC385
Decorative cover (accessory)
− +
–
Power cable plug
(accessory)
+
Important:
• Be sure to use the power cable plug provided with this product.
• Be sure to fully insert the power cable plug into the
12 V DC power supply terminal. Otherwise, it may damage the camera or cause malfunction.
w Rotate the decorative cover clockwise into the mount bracket until the "LOCK" indications on both sides of the cover reaches the decorative cover guide of the mount bracket.
LOCK
OPEN
Decorative cover guide
WV-SC385
LOCK OPEN
LOCK OPEN
Important:
• Make sure that no cable is pinched by the decorative cover.
19
Wire without making a hole in the ceiling
Step 1
Install the camera by following step 1 and steps 3 - 8 of the
"Wire through a hole in the ceiling" section (☞ pages 16 - 18). It is unnecessary to make a hole in the ceiling as described in step
2 of the "Wire through a hole in the ceiling" section.
Step 2
Remove the tab on the rear of the decorative cover (accessory) that is blocking the wiring hole.
Attach the decorative cover by following step 9 of the "Wire through a hole in the ceiling" section (☞ page 19).
Wire through the wiring hole of the decorative cover.
LOCK
OPEN
LOCK
OPEN
Place the camera upside-down by fixing on the bracket
SC385
When using the camera upside-down, fix the camera using the camera mount bracket (accessory) to prevent a fall. If necessary, attach the decorative cover (accessory) to the camera.
Install the camera by following step 1 and steps 3 - 9 of the "Wire through a hole in the ceiling" section (☞ pages 16 - 19).
When using the camera upside-down, select "On (desktop)" for "Upside-down" on the [Cam. Function] tab of the setup menu. (☞ Operating Instructions (PDF))
WV-SC385
20
Important:
• Prepare four fixing screws (M4 or M6) to be used to mount the camera mount bracket (accessory) according to the material of the place where the camera mount bracket is to be installed.
Place the camera upside-down on a desktop without fixing
SC385
Use it as a simple desktop device at meetings and on other occasions.
Place the camera on a level place not subject to vibrations.
Ensure that the camera does not fall.
When using the camera upside-down, select "On (desktop)" for "Upside-down" on the [Cam. Function] tab of the setup menu. (☞ Operating Instructions (PDF))
WV-SC385
Pass the power cable from a 12 V DC power supply (accessory) through the cable guides after connecting the power cable plug to the 12 V DC power supply terminal.
EXT I/O EXT I/O
4 3 2 4 3 2
Power cable
Cable guide
21
22
Installation examples
The following are installation examples in which a mount bracket (option) is used with this camera.
<For using the WV-Q154S>
• Embedded box (locally procured) • Strong wall
Embedded box
(locally procured)
WV-Q154S (option)
• Concrete
Camera
Anchor bolt
(locally procured)
Anchor bolt
(locally procured)
<For using the WV-Q155S>
Ceiling board such as plaster board
Dome cover
Roof space
Safety wire
Safety wire angle
WV-Q155S (option)
Camera
Inner cover
Decorative cover
<For using the WV-Q156S>
Safety wire angle
Safety wire
Anchor bolt
Camera
WV-SC385
WV-Q105 (option)
Mounting screws (4 pcs, WV-Q105 supplied)
Ceiling board such as plaster board
WV-Q156S (option)
Inner cover
Dome cover
23
24
Connection example
When connecting with a PC directly
Powered speaker (option)
PC
Microphone (option)
LAN cable
(category 5 or better, cross, STP*)
To AC outlet
<Required cable>
LAN cable (category 5 or better, cross, STP*)
* PAL model only
When connecting to a network using a PoE hub
Video monitor
(for adjustment use only)
Powered speaker
(option)
PoE device (hub)
Microphone (option)
LAN cable (category 5 or better, straight, STP*)
LAN cable
(category 5 or better, straight, STP*)
PC
Powered speaker
(option)
LAN cable
(category 5 or better, straight, STP*)
Microphone (option)
Video monitor
(for adjustment use only)
<Required cable>
LAN cable (category 5 or better, straight, STP*)
* PAL model only
Important:
• The video monitor is used for checking the adjustment of the angular field of view when installing the camera or when servicing. It is not provided for recording/monitoring use.
• Depending on the monitor, some characters (camera title, preset ID, etc.) may not be displayed on the screen.
• Use a switching hub or a router which is compliant with 10BASE-T/100BASE-TX.
• Power supply is required for each network camera. When using a PoE device (hub), 12 V DC power supply is unnecessary.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 4 Important safety instructions
- 5 Limitation of liability
- 5 Disclaimer of warranty
- 6 Preface
- 6 Main functions
- 7 About the user manuals
- 7 About notations
- 7 System requirements for a PC
- 8 Trademarks and registered trademarks
- 8 About copyright and license
- 8 Network security
- 9 Precautions
- 12 Precautions for installation
- 13 Major operating controls
- 15 Installations/Connections
- 25 Detach the camera
- 26 Insert/remove an SDHC/SD memory card
- 28 Configure the network settings
- 30 Troubleshooting
- 34 Specifications
- 37 Standard accessories
- 37 Optional accessories