advertisement
3.1
Introduction
This chapter describes basic features and procedures for using the panel PC. Topics covered include the floppy drive, CD-ROM drive,
I/O ports, touchscreen, and so on.
3.2
Floppy Drive
To insert a diskette, hold it with your left hand, between your thumb and your other fingers, and push it toward the drive. (See Fig. 3-1.)
Slide the disk until it clicks into place. Note that new diskettes must be formatted by your operating system before you can use them for data storage. See your operating system manual for details.
To eject a diskette, first ensure that the drive activity light is off, and then press the eject button on the drive. When the diskette pops out of the drive, remove it and store it properly.
Floppy disk drive
Floppy disk
Figure 3-1: Inserting and ejecting a floppy diskette
22
PPC-123 User's Manual
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 18 Introduction
- 20 How to Use This Manual
- 22 Specifications
- 22 General
- 22 Standard PC functions
- 23 PCI SVGA/flat panel interface
- 23 Audio function
- 24 PCI bus Ethernet interface
- 24 PCMCIA interface
- 24 Touchscreen (optional)
- 25 Optional modules
- 25 Environment
- 26 Dimensions
- 28 A Quick Tour of the Panel PC
- 31 Preparing For First-time Use
- 31 Installation Procedures
- 31 2.3.1 Connecting the power cord
- 32 2.3.2 Connecting the keyboard and mouse
- 32 2.3.3 Switching on the power
- 33 Running the BIOS Setup Program
- 34 Installing System Software
- 35 Installing the Drivers
- 38 Introduction
- 38 Floppy Drive
- 39 CD-ROM Drive
- 40 PCMCIA
- 43 PS/2 Mouse and Keyboard
- 43 PCI/ISA Bus Expansion
- 45 Parallel Port
- 45 Serial COM Ports
- 46 VGA Port
- 46 3.10 Game Port
- 46 3.11 USB Ports
- 47 3.12 Audio Interface
- 47 3.13 Ethernet
- 47 3.14 Adjusting the LCD Contrast and Brightness
- 48 3.15 Infrared Module
- 48 3.16 Touchscreen (Optional)
- 50 Upgrading
- 50 Disassembling the Panel PC
- 52 Installing the 2.5" Hard Disk Drive (HDD)
- 53 Installing the Central Processing Unit (CPU)
- 56 Installing the SDRAM Memory Module
- 57 ROM Drive
- 60 Jumpers and Connectors
- 60 5.1.1 Setting jumpers
- 61 5.1.2 Jumpers and switch
- 62 5.1.3 Locating jumpers and switch
- 63 5.1.4 Connectors
- 64 5.1.5 Locating connectors
- 65 CPU Installation
- 65 CMOS Clear for External RTC (JP8)
- 66 COM-port Interface
- 66 5.4.1 COM2 RS-232/422/485 setting (JP3, JP4, JP5)
- 67 5.4.2 COM1 / COM2 pin 9 output type setting (JP9)
- 68 5.4.3 COM3 / COM4 pin 9 output type setting (JP6)
- 68 Internal -12 V source selection setting (JP1)
- 69 VGA Interface
- 69 5.6.1 LCD panel power setting
- 69 5.6.2 Panel type select (SW1)
- 70 Watchdog Timer Configuration
- 70 5.7.1 Watchdog activity selection (JP7)
- 72 Introduction
- 72 Installation of Ethernet Driver
- 73 6.2.1 Installation for Windows
- 75 6.2.2 Installation for Windows
- 77 6.2.3 Installation for Windows NT
- 79 Further Information
- 82 Introduction
- 82 7.1.1 Chipset
- 82 7.1.2 Display memory
- 82 7.1.3 Display types
- 83 Installation of SVGA Driver
- 84 7.2.1 Installation for Windows
- 86 7.2.2 Installation for Windows
- 88 7.2.3 Installation for Windows NT
- 90 Further Information
- 92 Introduction
- 92 Installation of Audio Driver
- 93 8.2.1 Installation for Windows
- 95 8.2.2 Installation for Windows NT
- 98 Award BIOS Setup
- 98 CMOS Setup Utility
- 99 Standard CMOS Setup
- 100 9.3.1 Hard Disk Configurations
- 101 BIOS Features Setup
- 105 Chipset Features Setup
- 107 Power Management Setup
- 110 PNP/PCI Configuration Setup
- 111 Load BIOS Defaults
- 112 Load Setup Defaults
- 112 9.10 Integrated Peripherals
- 114 9.11 Password Setting
- 115 9.12 IDE HDD Auto Detection
- 116 9.13 Save and Exit Setup
- 116 9.14 Exit Without Saving
- 118 10.1 Introduction
- 118 10.2 Installation of PCMCIA Driver
- 119 10.2.1 Installation for Windows
- 122 11.1 Introduction
- 122 11.1.1 General information
- 122 11.1.2 General specifications
- 122 11.1.3 Environmental specifications
- 124 11.2.1 Installation for Windows
- 126 11.2.2 Installation for Windows
- 128 11.2.3Installation for Windows NT
- 131 11.3.1 Installation for Windows 95/98/NT
- 134 PPC-123 LCD Specifications
- 136 Programming the Watchdog Timer
- 140 Full Disassembly Procedures
- 148 AT Power Connector (J1)
- 148 TV Output Connector (J2) (*Reserved)
- 149 Inverter Power Connector (J4)
- 149 Internal Speaker Connector (J6)
- 149 Touchscreen Power Connector (J7)
- 150 (*Reserved)
- 150 IR Connector (J9)
- 151 Flat Panel Display Connector (CN2)
- 152 Flat Panel Display Connector (CN3)
- 153 D.10 PanelLink Interface (CN4) (*Reserved)
- 154 D.11 Floppy Drive Connector (CN10)
- 155 D.12 Internal COM4 Connector (CN15)
- 156 D.13 EIDE Hard Disk Drive Connector (CN16)
- 157 D.14 CD-ROM Connector (CN18)
- 158 D.15 CPU Fan Power Connector (FAN1)
- 158 D.16 System Fan Power Connector (FAN2)
- 159 D.17 PCI/ISA Bus Expansion Connector (SLOT1)
- 164 D.18 COM
- 166 Introduction
- 166 Panel Mounting
- 166 E.2.1 Introduction
- 167 E.2.2 Installation procedure
- 168 Desktop Stand Mounting
- 170 Swingarm Stand Mounting