- No category
advertisement
LS
9. STATUS MESSAGES
SS7 SERIES
1. Control mode indication: Local (L), Remote (R), Serial Comms (C), Jog (G),
Pump control (P).
2. SS7 status indication. See status message list. RDY = READY.
3. Average phase current.
4. Average input voltage.
Display Name
RDY
READY
ITQ
ACL
INITIAL TORQUE
ACCELERATING
RUN
DEC
HAM
LS+
LS-
DCB
UNV
OVV
OVL
UDL
PTC
OVT
RUNNING
DECELERATING
HAMMER
SLOW SPEED +
SLOW SPEED -
DC BRAKE
UNDERVOLTAGE
OVERVOLTAGE
OVERLOAD
UNDERLOAD
MOTOR PTC
SOFTSTARTER
OVERTEMPERATURE
Figure 9.1 Display. Status messages
Description
The SS7 is ready to run.
The SS7 is applying the Initial Torque specified at G4.4 Initial Torque for the time specified at G4.5 Initial Torque Time.
Motor is accelerating.
The motor runs at nominal Speed, after the acceleration ramp is finished
(Output voltage = Input voltage).
The Motor is decelerating.
Water Hammer algorithm is operating.
SS7 is applying Slow Speed + (CLOCKWISE).
SS7 is applying Slow Speed - (COUNTER-CLOCKWISE).
DC Brake current applied at the end of the ramp down.
Low mains supply.
High mains supply.
Overload condition.
Underload condition.
Motor PTC fault.
The temperature inside the softstarter is too high.
STATUS MESSAGES
31
SS7 SERIES
ILT
HIP
LOP
NOF
LWA
Display
SHP
ASY
FLT
STD
EXT
P/T
Name
SHEARPIN CURRENT
ASYMMETRIC
CURRENT
FAULT
START DELAY
EXTERNAL FAULT
TORQUE PULSE
CURRENT LIMIT
HIGH PRESSURE
LOW PRESSURE
NO FLOW
LOW WATER
Description
The shearpin function has switched off the softstarter.
Asymmetric current at the motor.
A fault has switched off the Softstarter.
The SS7 delays the start signal set in screen G4.1 Start delay.
Fault status is active due to an external fault command through one of the digital inputs.
The SS7 is applying torque pulse set in screen G4.2 moment during the time set in screen G4.3.
The SS7 has reached a maximum current level allowed in screen G4.7.
Current limit.
It warns during the time entered in screen G16.4.
It warns during the time entered in screen G16.5. and G16.6.
It warns during the time entered in screen G16.7 and G16.8.
It warns during the time entered in screen G16.9.
LS
32
STATUS MESSAGES
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 1 Electronic Softstarter
- 1 Getting Started Manual
- 9 INTRODUCTION
- 9 Code Description
- 10 Description of the Equipment
- 11 INSTALLATION AND CONNECTION
- 11 Environmental Conditions
- 11 Degree of Protection
- 11 Installation of the Softstarter
- 12 Power Loss Dissipation
- 12 Power Connections and Control Wiring
- 12 Power Connections
- 15 Control Wiring
- 17 Considerations before commissioning the SS7 Softstarter
- 19 POWER RANGE
- 19 SS7 Standard Softstarter
- 20 SS7 Softstarter with Internal Bypass
- 22 TECHNICAL CHARACTERISTICS
- 23 DIMENSIONS
- 23 Dimensions for Frames 1 and 2
- 24 Dimensions for Frames 3 and 4
- 25 Dimensions for Frame 5
- 26 CONFORMITY DECLARATION
- 27 CONNECTION TERMINALS
- 27 Control Connection Drawing
- 28 Terminal Description
- 29 DISPLAY UNIT AND KEYPAD OPERATION
- 29 LCD Display
- 29 Control Keys
- 30 Start and Stop-Reset / Slow Speed Buttons
- 31 Status messages
- 33 GENERAL INFORMATION SCREENS
- 34 PARAMETERS DESCRIPTION
- 34 Group 1 – G1: MENU OPTIONS
- 35 Group 2 – G2: NAMEPLATE
- 35 Group 3 – G3: PROTECTIONS
- 37 Group 4 – G4: ACCELERATION
- 39 Group 5 – G5: DECELERATION
- 40 Group 6 – G6: INPUTS
- 42 Group 7 – G7: OUTPUTS
- 44 Group 8 – G8: DUAL SETTING
- 47 Group 9 – G9: COMPARATOR
- 48 Group 10 – G10: FAULT HISTORY
- 49 Group 11 – G11: STATISTICS
- 50 Group 12 – G12: SLOW SPEED
- 51 Group 13 – G13: DC BRAKE
- 51 Group 14 – G14: SERIAL COMMUNICATION
- 52 Group 15 – G15: AUTO RESET
- 52 Group 16 – G16: PUMP CONTROL 1
- 54 FAULT MESSAGES. DESCRIPTION AND ACTIONS
- 58 COMMONLY USED CONFIGURATIONS
- 58 Settings
- 58 Recommended Power Installation
- 59 Operation Mode
- 61 CONFIGURATION REGISTER