advertisement
Integrated Web Server
Access protection
9.5
Access protection
Access to the drive parameters and diagnostics information can be protected by a password. Access protection is deactivated at the factory. You can activate the access protection function by assigning a password [2]. To deactivate the function again, delete the password (blank password).
If access protection is activated, a login dialog [1] will appear to request the saved password.
9
[1] Login [2] Config Login
[1]
[2]
61662AXX
Under "User" in the login dialog, you can select "Observer" or "Maintenance".
• Observer
– The drive unit parameters can be read with MOVITOOLS
®
MotionStudio but cannot be not changed.
– The current parameter settings can be uploaded from the unit to the PC (parameter set upload).
– It is not possible to download a parameter set or an IPOS plus®
program.
– Diagnostics via MOVITOOLS
®
MotionStudio is possible, the scope settings, however, cannot be changed.
• Maintenance
– MOVITOOLS
®
MotionStudio can be operated without any limitations.
Manual – Fieldbus Interface DFE33B EtherNet/IP and Modbus/TCP
107
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 6 1 General Information
- 6 Using the manual
- 6 Structure of the safety notes
- 7 Rights to claim under warranty
- 7 Exclusion of liability
- 7 Copyright
- 8 2 Safety Notes
- 8 Other applicable documentation
- 8 General safety notes for bus systems
- 8 Safety functions
- 8 Hoist applications
- 8 Product names and trademarks
- 8 Waste disposal
- 9 3 Introduction
- 9 Content of the manual
- 9 Additional documentation
- 9 Properties
- 10 3.3.2 Access to all information
- 10 3.3.3 Monitoring functions
- 10 3.3.4 Diagnostics
- 10 3.3.5 Fieldbus monitor
- 11 4 Assembly and Installation Instructions
- 11 MDX61B
- 12 4.1.1 Before you begin
- 13 (MDX61B, sizes 1 – 6)
- 14 the DFE33B option
- 17 Installing the DFE33B gateway / UOH11B
- 18 Connection and terminal description of the DFE33B option
- 19 Status LED of the DFE33B option
- 20 4.5.1 Gateway LED
- 21 Pin assignment
- 22 The integrated Ethernet switch
- 22 Shielding and routing bus cables
- 23 Setting the DIP switches
- 24 4.10 TCP/IP addressing and subnetworks
- 26 4.11 Setting the IP address parameters
- 28 4.12 Procedure for replacing the unit
- 29 B / gateway
- 30 5 Project Planning and Startup (EtherNet/IP)
- 30 Validity of the EDS file for DFE33B
- 31 Configuring the master (EtherNet/IP scanner)
- 32 MDX61B
- 34 the UOH11B gateway housing
- 36 5.2.3 Auto Setup for gateway operation
- 37 MDX61B inverter
- 38 B frequency inverter
- 39 Project planning examples in RSLogix
- 39 B with 10 PD data exchange
- 43 B via gateway DFE33B / UOH11B
- 53 B unit parameter access via DFE33B / UOH11B
- 54 6 Ethernet Industrial Protocol (EtherNet/IP)
- 54 Introduction
- 54 Process data exchange
- 55 CIP object directory
- 68 Return codes for parameter setting via explicit messages
- 72 7 Project Planning and Startup (Modbus/TCP)
- 72 Unit description file for Modbus/TCP
- 72 Configuring the master (Modbus scanner)
- 74 MDX61B
- 75 the UOH11B gateway housing
- 76 7.2.3 Auto Setup for gateway operation
- 77 MDX61B inverter
- 78 B frequency inverter
- 79 Project planning examples in PL7 PRO
- 79 B with 3 PD data exchange
- 81 B via gateway DFE33B / UOH11B
- 83 Examples for data exchange via Modbus/TCP
- 84 7.6.1 Writing and reading process data
- 86 7.6.2 Parameter access
- 88 8 Modbus Protocol (Modbus/TCP)
- 88 Introduction
- 88 8.1.1 Mapping and addressing
- 89 8.1.2 Services (function codes)
- 89 8.1.3 Access
- 90 Protocol structure
- 90 8.2.1 Header
- 91 8.2.2 Service FC3 – Read Holding Registers
- 92 8.2.3 Service FC16 – Write Multiple Registers
- 93 8.2.4 Service FC23 – Read/Write Multiple Registers
- 94 8.2.5 Service FC43 – Read Device Identification
- 95 Connection management
- 95 8.3.1 Sending process output data (request controlling connection)
- 96 8.3.2 Closing the connections
- 96 8.3.3 Timeout monitoring
- 97 Parameter access via Modbus/TCP
- 97 8.4.1 Procedure with FC16 and FC
- 97 8.4.2 Procedure with FC
- 98 8.4.3 Protocol structure
- 99 parameter channel
- 100 Fault codes (exception codes)
- 101 9 Integrated Web Server
- 101 Software requirements
- 101 Security settings
- 102 Design of the homepage of the integrated web server
- 103 Layout of the diagnostics applet
- 107 Access protection
- 108 MotionStudio Via Ethernet
- 108 MotionStudio
- 108 10.1.1 Tasks
- 108 10.1.2 Establishing communication with units
- 108 10.1.3 Executing functions with the units
- 109 10.2 First steps
- 109 10.2.1 Starting the software and creating the project
- 109 10.2.2 Establishing communication and scanning the network
- 110 10.3 Communication mode
- 110 10.3.1 Overview
- 111 10.3.2 Selecting communication mode (online or offline)
- 112 10.4 Serial communication (RS485) via interface adapters
- 112 10.4.1 Engineering via interface adapters (serial)
- 112 10.4.2 Starting up the USB11A interface adapter
- 115 10.4.3 Configuring serial communication
- 117 10.4.4 Serial communication parameter (RS485)
- 118 10.5 Communication via Ethernet
- 118 10.5.1 Connecting the unit with the PC via Ethernet
- 118 10.5.2 Address Editor
- 122 10.5.3 Configuring the communication channel via Ethernet
- 123 10.5.4 Setting the communication parameters for SMLP
- 124 10.5.5 Communication parameters for SMLP
- 125 10.6 Executing functions with the units
- 125 10.6.1 Parameter setting for units in the parameter tree
- 125 10.6.2 Reading/changing unit parameters
- 126 10.6.3 Starting up the units (online)
- 126 10.6.4 Special configuration and diagnostics tools
- 127 11 Ethernet Configuration Parameters
- 127 11.1 Parameter description
- 129 12 Troubleshooting
- 129 12.1 Diagnostic sequence
- 131 12.2 Error list in gateway operation
- 132 13 Technical Data
- 133 the gateway housing
- 134 14 Appendix
- 134 14.1 Parameter access to lower-level units via EtherNet/IP
- 135 14.2 Parameter access to lower-level units via Modbus/TCP
- 136 14.3 Parameter access to lower-level units via engineering interfaces
- 137 14.4 Glossary
- 138 15 Index