Preface. Imagine communications INH750 SA, INH750 DA

PDF

문서

Infocaster™ INH750DA and SA

Hardware Manual

Preface

Manual Information

Purpose

This manual details the features, installation, operation, maintenance, and specifications of the INH750 system.

Audience

This manual is written for engineers, technicians, and operators responsible for the system installation and set up.

Writing Conventions

This manual adheres to the following writing conventions.

Writing Conventions

Term or Convention

CAPS

Code

> hyperlink

Note:

Description

Indicates a specific key on the keyboard, such as ENTER,

TAB, CTRL, ALT, DELETE

Indicates variables or command-line entries, such as a

DOS entry or something you type into a field.

Indicates the direction of navigation through a hierarchy of menus and windows.

Indicates a jump to another location within the electronic document or elsewhere.

Indicates important information that helps to avoid and troubleshoot problems.

Unpacking/Shipping Information

Imagine Communications has carefully inspected, tested, and calibrated this product prior to shipment to ensure years of stable and trouble free service.

Before you install and configure your system, follow these steps:

1. Check equipment for any visible damage that may have occurred during transit.

2. Confirm that you have received all items listed on the packing list.

Infocaster™ INH750DA and SA

Hardware Manual

3. Contact your Imagine Communications sales representative if any parts are missing.

Preface

4. Contact the carrier if any item is damaged.

5. Remove all packaging material from the product and its associated components before you install the unit.

Keep at least one set of original packaging, in the event that you need to return a product for servicing.

If the original packaging is not available, you can purchase replacement packaging from Imagine

Communications at a modest cost or supply your own packaging as long as it meets the following criteria:



The packaging must be able to withstand the weight of the product.



The product must be held rigid within the packaging.



There must be at least two inches (5 cm) of space between the product and the container.



The corners of the product must be protected.

If the product is still within the warranty period, Imagine Communications will return the product to you prepaid after servicing.

Safety Standards and Compliances

Safety Terms and Symbols

This manual uses the following safety terms and symbols to identify certain conditions or practices.

WARNING

Identifies conditions or practices that can result in personal injury or loss of life—high voltage is present. Uninsulated dangerous voltage within the product’s enclosure may be sufficient to constitute a risk of electric shock to persons.

CAUTION

Identifies conditions or practices that can result in damage to the equipment or other property. Important operating and maintenance (servicing) instructions are included in the literature accompanying the product.

Restriction on Hazardous Substances (RoHS) Directive

Directive 2002/95/EC–commonly known as the European Union (EU) Restriction on Hazardous

Substances (RoHS)–sets limits on the use of certain substances found in electrical and electronic equipment. The Directive takes effect on July 1, 2006, and it refers to the following hazardous substances:

Infocaster™ INH750DA and SA

Hardware Manual



Lead (Pb)



Mercury (Hg)



Cadmium (Cd)



Hexavalent Chromium (Cr-V1)



Polybrominated Biphenyls (PBB)



Polybrominated Diphenyl Ethers (PBDE)

Preface

All relevant Imagine Communications products either comply with the legislation or are exempt. For example, spare parts supplied for the repair and upgrade of equipment sold before July 1, 2006 are exempt from the legislation.

Figure 1: RoHS Compliant Symbol

Waste from Electrical and Electronic Equipment (WEEE)

Directive

The European Union (EU) Directive 2002/96/EC on Waste from Electrical and Electronic Equipment

(WEEE) deals with the collection, treatment, recovery, and recycling of electrical and electronic waste products. The objective of the WEEE Directive is to assign the responsibility for the disposal of associated hazardous waste to either the producers or users of these products. Producers or users are required to recycle electrical and electronic equipment at end of its useful life, and must not dispose of the equipment in landfills or by using other unapproved methods.

In accordance with this EU Directive, Imagine Communications has affixed labels indicating that such products must be properly recycled. Contact your local Imagine Communications sales representative for information on returning these products for recycling. Imagine Communications equipment that complies with the EU directive will be marked with a WEEE-compliant symbol, as shown below.

Figure 2: WEEE Compliance Symbol

Infocaster™ INH750DA and SA

Hardware Manual

Declaration of Conformity

Preface

Imagine Communications declares that the following INH750 system options are in conformity with the standards stated in this note.

Part Number

INH750DA

INH750SA

Description

Infocaster Ultra Small Form Factor Digital Signage Platform, Fanless, disk drive.

Infocaster Ultra Small Form Factor Digital Signage Platform, Fanless, solid-state drive.

The Imagine Communications system options previously listed are in conformity with the following standards.

FCC



FCC 47 CFR Part 15 Subpart B/Oct. 2010



CISPR 22/1997 (Class B Limit)



ANSI C63.4-2003

Safety Guidelines

Adhere to the following safety guidelines to avoid personal injury or damage to your system.

Electrical Safety Guidelines

Power Cords

WARNING

To avoid electrical shock, check the power cords properly.



Use the exact type of power cords as required.



Be sure to use power cord(s) that came with safety certifications.



The power cord(s) must be compliant with the AC voltage requirements in your region.



The power cord plug cap must have an electrical current rating that is at least 125% of the electrical current rating of this product.



The power cord plug cap that plugs into the AC receptacle on the power supply must be an IEC 320, sheet C13, type female connector.



Plug the Power cord(s) into a socket that is properly grounded before turning on the power.



This hardware contains hazardous voltage levels. To avoid electrical shock, disconnect all cords before accessing the system chassis or its components.

Infocaster™ INH750DA and SA

Hardware Manual

General Electrical Safety Guidelines

Preface

WARNING

Adhere to the following Electrical Safety Guidelines to avoid possible damages to the system or injury to yourself.



Be aware of the locations of the power switches on the chassis and in the room, so you can disconnect the power supply if an accident occurs.



Take extra precautionary measures when working with high voltage components. It is not recommended to work alone.



Before removing or installing main system components, be sure to disconnect the power first. Turn off the system before you disconnect the power supply.



Use only one hand when working with powered-on electrical equipment to avoid possible electrical shock.



Use rubber mats specifically designed as electrical insulators when working with computer systems.



The power supply or power cord must include a grounding plug and must be plugged into grounded outlets.



This product is suitable for connection to IT power sources.



CAUTION - RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED

BATTERIES ACCORDING TO THE INSTRUCTIONS.



Make sure not to install the motherboard battery upside down to avoid possible explosion. Make sure that the positive side should be facing up on the motherboard.

Protective Earth Requirements



The building installation shall provide a means for connection to protective earth; and

The equipment is to be connected to that means; and

A service person shall check whether or not the socket-outlet from which the equipment is to be powered provides a connection to the building protective earth. If not, the service person shall arrange for the installation of a protective earthing conductor from the separate protective earthing terminal to the protective earth wire in the building.

General Safety Guidelines

WARNING

Adhere to the following General Safety Guidelines to ensure your personal safety.



Equipment is for use only in restricted access locations where only trained personnel have access.



Keep the area around the the chassis clean and free of clutter.



Avoid wearing loose clothing to preventing it from coming into contact with power circuits.



After removing the components or chassis cover from the system, place them on a table for safeguard.



Be sure to remove any jewelry or metal objects before working on the chassis to avoid short circuits should these objects come into contact with power circuits.

Infocaster™ INH750DA and SA

Hardware Manual



After accessing the interior of the chassis, be sure to replace and secure the chassis cover.

Preface

ESD Safety Guidelines

CAUTION

Electric Static Discharge (ESD) can damage electronic components. To prevent damage to your system board, it is important to handle it very carefully.

The following measures are generally sufficient to protect against Electric Statics Discharge (ESD).



Use a grounded wrist strap designed to prevent static discharge.



Keep all components and printed circuit boards (PCBs) in their anti-static bags until ready for use.



Touch a grounded metal object before removing the board from the anti-static bag.



Do not let components or PCBs come into contact with your clothing, which may retain a charge even if you are wearing a wrist strap.



Touch a grounded metal object before removing the board from the anti-static bag.



Handle a board by its edges only; do not touch its components, peripheral chips, memory modules or contacts.



When handling chips or modules, avoid touching their pins.



Put the motherboard and peripherals back into their anti-static bags when not in use.



For grounding purposes, make sure your computer chassis provides excellent conductivity between the power supply, the case, the mounting fasteners and the motherboard.