advertisement
3.
240 VOLT SINGLE PHASE OPERATION
The motor supplied with your machine is a dual voltage,
120/240 volt motor. It is shipped ready-to-run for 120 volt operation. However, it can be converted for 240 volt operation.
A qualified electrician should do the conversion, or the machine can be taken to an Authorized DELTA® Service
Center. When completed, the machine must conform to the National Electric Code and all local codes and ordinances.
The machine is converted by re-wiring the motor for 240 volts, installing a 240 volt plug on the power supply cord and replacing the switch with one that is rated for 240 volt operation.
Be sure the 240 volt plug is only used in an outlet having the same configuration as the plug illustrated in Fig. C.
No adapter should be used with the 240 volt plug.
In all cases, make certain that the receptacle in question is properly grounded. If you are not sure, have a qualified electrician check the receptacle.
EXTENSION CORDS
GROUNDED OUTLET BOX
CURRENT CARRYING
PRONGS
GROUNDING BLADE IS
LONGEST OF 3 BLADES
FIG. C
Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire extension cord which has a 3-prong grounding type plug and matching receptacle which will accept the machine’s plug. When using an extension cord, be sure to use one heavy enough to carry the current of the machine. An undersized cord will cause a drop in line voltage, resulting in loss of power and overheating. Fig. D-1 or D-2, shows the correct gauge to use depending on the cord length. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.
MINIMUM GAUGE EXTENSION CORD
RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES
Ampere
Rating
0-6
0-6
0-6
0-6
6-10
6-10
6-10
6-10
10-12
10-12
10-12
10-12
12-16
12-16
12-16
Volts
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
Total Length of
Cord in Feet up to
25
25-50
50-100
100-150 up to
25
25-50
50-100
100-150 up to
25
25-50
50-100
100-150
Gauge of
Extension Cord
18 AWG
16 AWG
16 AWG
14 AWG
18 AWG
16 AWG
14 AWG
12 AWG
16 AWG
16 AWG
14 AWG
12 AWG up to
25
25-50
14 AWG
12 AWG
GREATER THAN 50 FEET NOT RECOMMENDED
MINIMUM GAUGE EXTENSION CORD
RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES
Ampere
Rating
0-6
0-6
0-6
0-6
6-10
6-10
6-10
6-10
10-12
10-12
10-12
10-12
12-16
12-16
12-16
Volts
240
240
240
240
240
240
240
240
240
240
240
240
240
240
240
Total Length of
Cord in Feet up to
50
50-100
100-200
200-300
Gauge of
Extension Cord
18 AWG
16 AWG
16 AWG
14 AWG up to
50
50-100
100-200
200-300 up to
50
50-100
100-200
200-300
18 AWG
16 AWG
14 AWG
12 AWG
16 AWG
16 AWG
14 AWG
12 AWG up to
50
50-100
14 AWG
12 AWG
GREATER THAN 100 FEET NOT RECOMMENDED
Fig. D-1 Fig. D-2
FUNCTIONAL DESCRIPTION
FOREWORD
The DELTA® Industrial Model 50-723 Dust Collector will connect to woodworking machines that accept a 4” diameter hose. The 50-723 comes with one 1 micron filter bag and two 6 mil plastic collection bag.
NOTICE: The photo on the manual cover illustrates the current production model. All other illustrations contained in the manual are representative only and may not depict the actual labeling or accessories included. These are intended to illustrate technique only.
6
advertisement
Key Features
- 1 HP Dust Collector
- 4” dust ports
- 1 micron filter bag
- two 6 mil plastic collection bags
Related manuals
Frequently Answers and Questions
What is the purpose of the dust collector?
What type of dust does this dust collector filter?
What type of hose does this dust collector use?
How do I start and stop the dust collector?
advertisement