advertisement
Connecting the Power Cord
POWER
_
ON
—
OFF
Before plugging the receiver into an AC outlet, make sure that all connections have been made.
1. Plug the power cord into an AC outlet.
2. Press POWER to set it in the
_
The STANDBY lamp lights up. A small amount of power is always consumed.
To shut off the power completely:
Press POWER to set it in the
—OFF position.
Keep the power cord away from the connecting cables for the TV, VCR, and antenna. The power cord may cause noise or screen interference. We recommend that you use a coaxial cable to connect the antenna, since it is well-shielded against interference.
The difference between the POWER switch and the STANDBY/ON button
• The POWER switch is the mains supply switch, allowing the receiver to connect to the mains supply.
To shut off the power completely, press the POWER switch to set it in the
—OFF position.
• The STANDBY/ON button is a functional on/off (standby) switch, and does not disconnect the receiver from the mains supply. A small amount of power is consumed even in standby mode for the receiver to accept signals from the remote control.
Note:
A preset settings such as preset channels and sound adjustments may be erased in the following cases:
• When you press POWER to set it in the
—OFF position.
• When you unplug the power cord.
• When a power failure occurs.
CAUTIONS:
• Do not touch the power cord with wet hands.
• Do not pull on the power cord to unplug the cord. When unplugging the cord, always grasp the plug so as not to damage the cord.
Putting Batteries in the Remote Control
Before using the remote control, put two supplied batteries first. When using the remote control, aim the remote control directly at the remote sensor on the receiver.
1. On the back of the remote control, remove the cover as illustrated.
2. Insert batteries. Make sure to observe the proper polarity: (+) to (+) and (–) to (–).
3. Replace the cover in.
R03 (UM-4)/AAA (24F)
Page 11
RX-730RBK(EF)0054-001A.En.01-28 11
If the range or effectiveness of the remote control decreases, replace the batteries. Use two R03 (UM-4)/AAA
(24F) type dry-cell batteries.
Note:
When you replacing the batteries, finish it without delay; otherwise, the control signals you have stored are all erased. (See pages 45 and 47.)
CAUTIONS:
Follow these precautions to avoid leaking or cracking cells:
• Place batteries in the remote control so they match the polarity indicated: (+) to (+) and (–) to (–).
• Use the correct type of batteries. Batteries that look similar may differ in voltage.
• Always replace both batteries at the same time.
• Do not expose batteries to heat or flame.
97.7.25, 6:26 PM
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 7 Getting Started
- 7 Before Installation
- 7 Checking the Supplied Accessories
- 8 Switches, Buttons and Controls
- 10 Connecting the FM and AM (MW/LW) Antennas
- 11 Connecting the Speakers
- 14 Connecting Audio/Video Components
- 16 Connecting the Power Cord
- 16 Putting Batteries in the Remote Control
- 17 Basic Operations
- 17 Turning the Power On and Off
- 17 Selecting the Source to Play
- 18 Adjusting the Volume
- 18 Selecting the Front Speakers
- 19 Muting the Sound
- 19 Recording a Source
- 20 Basic Settings
- 20 Adjusting the Front Speaker Output Balance
- 20 Listening at Low Volume (Loudness)
- 21 Using the Sleep Timer
- 22 Selecting the Center Speaker Size
- 23 Using Visual Confirmation
- 24 One Touch Operation
- 24 About the One Touch Operation
- 24 Using the One Touch Operation
- 25 Receiving Radio Broadcasts
- 25 Tuning in Stations Manually
- 25 Using Preset Tuning
- 26 Selecting the FM Reception Mode
- 27 Assigning Names to Preset Stations
- 28 Using the RDS (Radio Data System) to Receive FM Stations
- 28 What Information Can RDS Signals Provide?
- 29 Searching for a Program by PTY Codes
- 31 Switching to a Broadcast Program of Your Choice Temporarily
- 32 Using the SEA Modes
- 32 Selecting Your Favorite SEA Mode
- 33 Creating Your Own SEA Mode
- 34 Using the Surround Processor
- 34 Using JVC’s Hall Surround
- 36 Speaker Arrangements for Dolby Surround
- 37 Preparing for Dolby Surround
- 41 Using Dolby Surround
- 42 Using the On-Screen Display to Control the Receiver
- 46 COMPU LINK Remote Control System
- 47 Using the Remote Control
- 47 Using the Remote Control for Operating JVC Audio/Video Components
- 50 Simplifying the Operations Using the Remote Control
- 52 Operating the Other Manufacturers’ Audio/Video Components
- 55 Troubleshooting
- 56 Specifications