Schema and Policy Rules For
Work Order Management
As part of the installation of the WorkOrder driver, Novell
®
eDirectory
TM
is extended to include two new object classes. These objects allow the driver to connect to the Identity Vault correctly, perform work orders, and create a process log with the work order status.
You can use iManager to create or view these objects in the Identity Vault. See
Chapter 6,
“Customizing the Driver,” on page 29
.
Section C.1, “DirXML-WorkOrder Object,” on page 51
Section C.2, “DirXML-WorkToDo Object,” on page 53
Section C.3, “Publisher Placement Rule,” on page 54
Section C.4, “Subscriber Placement Rule,” on page 54
Section C.5, “Subscriber Create Rule,” on page 54
C.1 DirXML-WorkOrder Object
The DirXML-WorkOrder object (sometimes referred to as the WorkOrder object in this documentation) is used to tell the driver what tasks to perform. It delays the work order until a date and time or until another work order is configured. It also repeats work orders at a given interval.
The following table shows the work order attributes you need to specify:
Table C-1
WorkOrder Object Attributes
Work Order Attributes
(eDirectory Namespace)
Description
Common Name
DirXML-woContact Name
DirXML-woContent
DirXML-DueDate
Description Type
Description of the work order. The driver does not change this attribute. It is passed through to the WorkToDo object when the work order is processed.
Case ignore string
The naming attribute for eDirectory
This attribute is passed through to the
WorkToDo object. It is used by policies to process the work order.
Case ignore string
Information about the work order. The driver does not change this attribute. It is passed through to the WorkToDo object when the work order is processed.
Case ignore string
Case ignore string
The date and time the work order is to be processed.
Time
C
Schema and Policy Rules For Work Order Management
51
Work Order Attributes
(eDirectory Namespace)
Description Type
DirXML-woDoItNowFlag
DirXML-woSendToPublisher If set to True, the Subscriber channel sends the work order to the Publisher channel to be written to the WorkOrder container. For example, if the work order was created by a policy as a result of an event in the Identity
Vault.
Boolean
DirXML-woType
If set to True, the Subscriber channel sends the work order to the Publisher channel to be processed immediately.
Boolean
DirXML-woCreationDate
Information about the work order. The driver does not change this attribute. It is passed through to the WorkToDo object when the work order is processed.
User defined
Information about the work order. The driver does not change this attribute.
Time
DirXMLwoDependentWorkOrder
DirXML-woRepeatInterval
DirXML-woRepeatCount
DirXML-woStatus
The DN of the dependent work order. The work order is not processed until the dependent work order has a status of
Configured. If the attribute is non-existent or empty, it is ignored.
Distinguished Name
The amount of time, in minutes, before the work order is repeated. This value is added to the due date after the work order is processed.
Case ignore string
Case ignore string Repeats the work order as many times as the number specifies. Use this attribute in association with the DirXMLwoRepeatInterval attribute.
Status of the work order.
Case ignore string
DirXMLwoWorkOrderNumber
DirXML-woDeleteOnError
DirXML-woProcessLog
Pending: The work order will be processed on the due date.
Configured: The work order was processed.
Error: An error occurred when processing.
On Hold: The work order is not to be processed.
Information about the work order. The driver does not change this attribute. It is passed through to the WorkToDo object when the work order is processed.
Case ignore string
If set to True, the work order is deleted if the status is Error and the DeleteDueDate has expired.
Boolean
Contains information relating to the processing of the work order.
Case ignore string
52
Identity Manager 3.6.1 WorkOrder Driver Implementation Guide.
