advertisement
S ET UP
Your product comes with:
• Safety Hitch Pin located at the bottom of the Vertical Column, which must be removed prior to unfolding.
• Height Adjustment Quick Release Pin located on back of Vertical Column for raising and lowering rails.
• One (1) Spring Loaded Pin locked into the base of the left rail by the height adjustment tube. Left side is determined by standing behind the unit facing the Vertical Column.
IMPORTANT: To Prevent Injury – Be sure the spring-loaded pin is locked securely into place in the left rail before using unit. This will prevent the height adjustment column from falling forward.
• Safety Pin - located on Lanyard/attached to Height Adjustment Tube.
• One Long Hitch Pin for Leg Pulley Bracket is located in the Miscellaneous Section of Accessory Kit as well as two
Medium Hitch Pins for the Wing Accessory, and 4 Short Hitch Pins for the Press Up Bars and Dip Bars.
IMPORTANT: Before using the Wing Accessory, Leg Pulley Accessory, Press Up Bars and Dip Bars, be sure the Hitch Pins are securely inserted (see page 8, 9 & 11 of this manual for directions).
• One (1) Bolt and two (2) Weight Clips are located on the Weight Bar.
IMPORTANT: Before using the Weight Bar, be sure the Weight Clips are installed
(see page 10 of this manual for directions).
1.
Pull the product out of the shipping box. Remove all packaging materials, including tape and cardboard inserts, from your unit.
Lift Here
3.
2.
Lay product on the floor with glideboard side up. Make sure you have plenty of space on both ends of the product. Slide the glideboard as far as it will go towards the Front Crossbar before you begin lifting unit.
3.
4.
5.
Lift the exerciser up by holding it at the top of the rails. Using your foot, slowly spread the unit open at the bottom approximately 12 inches so that it rests firmly on the Front and Back Crossbars not allowing it to go too far.
Back
Crossbar
12”
Front
Crossbar
Make sure the handles are out to the sides before you begin to unfold your unit. Keep hands and fingers away from pulley. Hold onto the top center of glideboard and begin rolling rear rollers. Spread the unit out until it is flat on the floor. Be careful to do this slowly.
Be sure to support the frame in the center to avoid having the product drop suddenly onto the floor or pinch fingers.
4.
Hold Here While Lowering
To The Ground
(a) Remove Safety Hitch Pin from bottom of Vertical Column. Next remove plastic packing ties from the top and bottom of the Vertical
Column. Pull out the Spring Loaded Pin Knob located at the left rail
(NOTE - pin shown in picture is on right side) to release Spring
Loaded Pin. Continue to hold pin out while performing the next step.
Spring
Loaded
Pin
5a
Safety
Hitch Pin
Knob
— 6 —
6.
(b) Take hold of the Vertical Column and pull it up until it is upright. Release the Spring Loaded Pin. You should hear it lock back into place.
5b
IMPORTANT: Be sure the Spring Loaded Pin is locked into place before using your unit. You will know the pin is locked into place when you can see the end protrude through the inside of the rail bracket.
Position one foot on Back Crossbar to keep the product from lifting off the floor. With one hand on either the right or left rail and the other hand holding the height adjustment Quick Release Pin out, slide the rails along the Vertical Column to desired position and release pin.
Pin will pop into place - you will hear a snap. Then turn knob to the right to tighten and secure. Last, insert straight Safety Pin (attached to the height adjustment tube) into the hole on Vertical Column just below the height adjustment bracket.
6.
NOTE: Insert Safety Hitch Pin in the side hole located at the bottom of the Vertical Column.
(This is the pin you removed in step 5a).
Height Adjustment
Quick Release Pin
Put Hitch Pin
Back Into Hole
7.
PILATES BAR ASSEMBLY
Assemble the Pilates Bar at the opposite end of the unit by inserting it into the Front Crossbar as pictured to the right.
Make sure it is fully inserted.
7.
8.
STOPPER ASSEMBLY
If the Stopper at the bottom of the Vertical Column has not already been installed, please do so now. Locate the Stopper which is packed in Miscellaneous Accessories (See Product Specifications on page 5 of this manual). Unscrew nut on the end of the Stopper and remove. Insert the Stopper into the hole located in the center of the Back Crossbar. (See Fig. 1) Screw the nut back onto the
Stopper and tighten with Allen Wrenches provided. (See Fig. 2)
IMPORTANT:
Proper installation of the Stopper is necessary for the Rollers to function easily when the unit is folded and rolled into place for storage.
8.
9.
Front Crossbar
Fig. 1
Fig. 2
Flip Chart
9.
To add the Flip Chart, remove the cap from the Vertical Column
(keep it for storage). Insert the Flip Chart holder base into the
Vertical Column. Then secure the Flip Chart onto the Flip Chart Base.
Flip Chart
Base
Vertical
Column
— 7 —
advertisement