WARNING

Checking Your Vent

Your washer/dryer must be properly installed and vented for the dryer to achieve maximum drying efficiency and shorten drying times. Use the minimum recommended installation clearances

(found in your Installation Instructions) to avoid blocking the flow of combustion and ventilation air. See the Installation Instructions for more information.

NOTE: Service calls caused by improper venting will be paid for by the customer, whether it was a paid installation or selfinstalled.

1. Do not use plastic vent or metal foil vent. Use 4 in. (10.2 cm) metal or flexible metal vent. Do not kink or crush flexible metal vent. It must be completely extended to allow adequate exhaust air to flow. Check vent after installation. Refer to your

Installation Instructions for proper length requirements of vent.

2. Use a 4 in. (10.2 cm) exhaust hood.

3. Use the straightest path possible when routing the vent.

Fire Hazard

Use a heavy metal vent.

Do not use a plastic vent.

Do not use a metal foil vent.

Failure to follow these instructions can result in death or fire.

If the washer/dryer is not properly installed and vented, it will not be covered under the warranty.

4. Use clamps to seal all joints. Do not use duct tape, screws or other fastening devices that extend into the interior of the vent to secure vent.

5. Clean exhaust vent periodically, depending on use, but at least every 2 years, or when installing your washer/dryer in a new location. When cleaning is complete, be sure to follow the

Installation Instructions supplied with your washer/dryer for final product check.

WASHER USE

Loading

For these suggested full-sized loads, set the LOAD SIZE selector to the highest load size setting.

LARGE CAPACITY WASHERS

Heavy Work

Clothes

2 pair of pants

3 pair of jeans

1 coverall

3 shirts

Mixed Load

2 double sheets

4 pillowcases

6 T-shirts

6 pair of shorts

2 shirts

2 blouses

6 handkerchiefs

Towels

8 bath towels

8 hand towels

10 washcloths

1 bath mat

Delicates

2 camisoles

4 slips

6 undergarments

2 sets of sleepwear

1 child’s outfit

Permanent

Press

1 double sheet

1 tablecloth

1 dress

1 blouse

2 pair of pants

3 shirts

2 pillowcases

Knits

2 pair of pants

2 blouses

4 shirts

4 tops

2 dresses

3

4

WARNING

Starting Your Washer

Style 1: With Liquid Fabric Softener Dispenser (on some models)

■

Use only liquid fabric softener in this dispenser. Pour measured liquid fabric softener into the dispenser.

Softener is added automatically during the rinse portion of the cycle. Dilute liquid fabric softener by filling the dispenser with warm water until liquid reaches the crossbar in the dispenser opening.

Fire Hazard

Never place items in the washer that are dampened with gasoline or other flammable fluids.

No washer can completely remove oil.

Do not dry anything that has ever had any type of oil on it (including cooking oils).

Doing so can result in death, explosion, or fire.

1. Measure detergent and pour it into the washer. If desired, add powdered or liquid color safe bleach. Drop a sorted load of clothes loosely into your washer.

■

Load evenly to maintain washer balance. Mix large and small items. Items should move easily through the wash water. Overloading can cause poor cleaning.

2. (OPTIONAL) Add Liquid Chlorine Bleach.

Always measure liquid chlorine bleach. Do not guess. Never use more than 1 cup (250 mL) for a full load. Follow manufacturer’s directions for safe use. Use a cup with a pouring spout to avoid spilling.

Let the washer fill and begin agitating the load. Add bleach to the wash cycle so it can be removed in the rinse cycle. Pour bleach around the agitator, not directly onto the load.

■

Follow directions on the care labels. Do not use chlorine bleach on wool, silk, spandex, acetates, or some flameretardant fabrics.

NOTE: Undiluted bleach will damage any fabric it touches.

The damage appears as rips, holes, tears, or color loss and may not show up until several washings later.

3. (OPTIONAL) Add Liquid Fabric Softener.

NOTE: Your washer/dryer does not come with a fabric softener dispenser installed.

To find out whether your model allows fabric softener dispenser usage and for ordering information, refer to the front page of this manual or call the dealer from whom you purchased your washer/dryer. Ask for Part Number 3350834.

NOTE: Do not spill or drip any fabric softener onto the clothes.

Undiluted fabric softener can stain fabrics. Always dilute fabric softener with warm water. Too much fabric softener can make some items (diapers and towels) nonabsorbent. If this happens, do not use it in every load, or use less of it in each load.

Style 2: Without Liquid Fabric Softener Dispenser (on some models)

■

In the final rinse ONLY, add fabric softener that has been diluted with

¹⁄₂ to 1 cup (125 to 250 mL) warm water.

4. Close the washer lid. Washer will not agitate or spin with the lid open.

5. Turn the WATER LEVEL selector to the correct setting for your wash load and the type of fabric being washed. You may change the load size or water level selection after the washer has started filling by turning the selector to a different setting.

6. Set the TEMPERATURE selector to the correct setting for the type of fabric and soils being washed. Use the warmest water safe for fabric. Follow garment label instructions.

NOTE: In wash water temperatures colder than 70ºF (21ºC), detergents do not dissolve well. Soils can be difficult to remove. Some fabrics can retain wear wrinkles and have increased pilling (the formation of small lint-like balls on the surface of garments).

7. Push in the Cycle Control knob and turn it clockwise to the wash cycle you want. Reduce the wash time when using a small load size setting. Pull out the Cycle Control knob to start the washer.

To stop or restart your washer:

■

■

To stop the washer at any time, push in the Cycle

Control knob.

To restart the washer, close the lid (if open) and pull out the

Cycle Control knob.