advertisement
CHAPTER 9
Tone Generator
9.1. Tone Generator
The Display handset (DH) as well as the Remote handset (RH) can generate a low tone, a high tone and an alternating tone, with a rate of 2 Hz between low and high alternating tone
("Warble"), which is recognized by most standard cable locators.
Illustration 9.1. Typical Application of Tone Generator
NOTE:
The keys WIREMAP, SHIFT and TONE are hard keys. The keys Pair A, Pair B, Pair C, Pair D,
Low, High and Warble are soft keys that are displayed on the Display handset (DH).
9.1.1. Enable Tone Generator with Display handset (DH)
1. Connect Display handset (DH) to cable to be tested.
2. Use Arrow Keys to navigate on ready screen to "Toner" display and confirm with
Enter.
73
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 8 II Cable Certifier
- 8 1.1. Technical Information
- 9 1.2. Product Specifications
- 9 1.3. Dimensions, Weights, Operating Conditions
- 10 1.4. Performance Specifications
- 11 Product Description
- 11 2.1. The Display Handset (DH)
- 11 2.1.1. Controls and Ports/Connectors
- 13 2.1.2. TFT Display
- 14 2.1.3. Function Keys F1 to F
- 14 2.1.4. Soft Key
- 15 2.2. The Remote Handset (RH)
- 15 2.2.1. Controls and Ports/Connectors
- 17 2.3. Power Management
- 17 2.3.1. Operating the Display and Remote handset from AC Power
- 18 2.3.2. Battery Charging
- 18 2.4. Talkset
- 19 Basics of the Cable Test
- 19 3.1. Testing of cables and relevant requirements
- 19 3.1.2. Setup for Permanent Link Test
- 19 3.1.3. Setup for Channel Link Test
- 20 Preferences
- 20 4.1. Open Preferences
- 20 4.2. Language
- 21 4.3. User Information
- 21 4.4. Autotest Options
- 22 4.5. Contrast
- 22 4.6. Timeout Options
- 23 4.7. Measurement Units
- 24 4.8. Talkset
- 24 4.9. Date and Time
- 25 4.10. Restore Default
- 26 4.11. Clear Memory
- 26 4.12. Temperature
- 27 Autotest
- 28 5.1. Set Autotest Pref
- 29 5.2. Select Job Folder
- 29 5.2.1. Enable Existing Job Folder
- 30 5.2.2. Create New Job Folder
- 32 5.3. Set Cable Name (cable ID)
- 33 5.3.1. Simple Cable ID
- 34 5.3.2. Default Cable ID
- 36 5.4. Labeling Standard TIA/EIA 606-A
- 37 5.4.1. Cable Name in Format TIA/EIA 606A
- 37 5.4.2. Cable Parameter 606A Drop
- 38 5.4.3. Cable Parameter 606A Backbone
- 38 5.4.4. Cable Parameter 606A Backbone Pair/Fiber
- 39 5.5. Select Twisted Pair Cabling
- 40 5.5.1. Specify Cable Type
- 40 5.5.2. Create Cable Type
- 43 5.5.3. Edit and Calculate NVP
- 44 5.5.4. Enter Reference Temperature
- 45 5.6. DualMODE™ Function for Twisted Pair Cabling
- 45 5.6.1. Implement DualMODE
- 46 5.7. Edit NVP Default Value of a Cable
- 47 5.8. Coaxial Cable Standards
- 48 5.8.1. Autotest Test Series for Coaxial Cables
- 49 5.9. Calibration
- 49 5.9.1. Twisted Pair Cabling
- 51 5.9.2. Coaxial Cable
- 52 5.10. Perform Autotest
- 52 5.11. Open Job Folder of Autotest
- 52 5.11.1. Job Options
- 52 5.11.2. Test Options
- 53 5.11.3. Copy Job Folder to USB Removable Storage
- 53 5.11.4. Alien Crosstalk Measurements (AXT)
- 53 5.12. Autotest Results and Graphs
- 55 5.12.1. Graph Formats, Layouts and Controls
- 57 Structured Cabling Testing
- 57 6.1. Test Setup for Single Test Analysis
- 57 6.2. Test Run of Single Test Analysis
- 57 6.3. Perform Single Test Analysis
- 58 6.4. Evaluation of Analysis Test Results
- 58 6.4.1. Graphs for Analysis Tests
- 58 6.5. Overview of Single Test Analysis
- 59 6.6. Wiremap Test
- 60 6.7. Length Test
- 60 6.7.1. Length Test Error
- 60 6.8. Resistance Test
- 60 6.8.1. Resistance Test Error
- 60 6.9. NEXT, ACR-F (ELFEXT) and Power Sum
- 61 6.10. Power Sum NEXT, Power Sum ACR-F (ELFEXT)
- 62 6.10.1. NEXT Test and ACR-F (Power Sum ELFEXT) Test Error
- 63 6.11. Insertion Loss Test (Attenuation)
- 63 6.11.1. Insertion Loss test Error
- 63 6.12. Return Loss Test
- 63 6.12.1. Return Loss Test Error
- 64 6.13. Impedance Test
- 64 6.13.1. Impedance Error
- 64 6.14. Delay and Skew Test
- 65 6.14.1. Delay and Skew Test Error
- 65 6.15. Capacitance Test
- 65 6.15.1. Capacitance Test Error
- 65 6.16. ACR-N (ACR) Test and Power Sum ACR-N (Power Sum ACR) Test
- 66 6.16.1. ACR-N (ACR) Test and Power Sum ACR-N (Power Sum ACR) Test Error
- 66 6.17. Headroom Test
- 66 6.17.1. Headroom Test Error
- 67 6.18. Custom Cable Preferences and Cable Parameters
- 67 6.18.1. Creating a New Customs Cable Type
- 68 6.18.2. Select Custom Cable Type
- 68 6.18.3. Custom Cable Parameters
- 70 Coaxial Cable Test
- 70 7.1. Properties of Coaxial Cables
- 70 7.2. Troubleshooting Coaxial Cables
- 71 Fiber Testing with FiberTEK™ FDX
- 71 8.1. Safety Precautions
- 71 8.2. Notes on Cleaning Measuring Adapter and Patch Cord
- 72 8.3. Performance Specification
- 73 Tone Generator
- 73 9.1. Tone Generator
- 73 9.1.1. Enable Tone Generator with Display handset (DH)
- 74 9.1.2. Enable Tone Generator with Remote handset (RH)
- 75 IDEAL DataCENTER Software
- 75 10.1. Installing Software
- 75 10.1.1. System Requirements
- 75 10.1.2. Start Installation
- 76 10.2. Select Language
- 76 10.3. Software-Update
- 76 10.3.1. Retrieve Version
- 76 10.3.2. Perform Update
- 77 10.4. Databases
- 77 10.4.1. Create a new database
- 78 10.4.2. Open an existing database
- 79 10.5. Transfer job file
- 79 II Cable Certifier
- 81 10.5.2. Import from the computer or an external data carriers (USB Flash Drive)
- 82 10.5.3. Export job folder
- 83 10.5.4. Rename job folder
- 84 10.6. Manage Tests
- 84 10.6.1. Edit information
- 85 10.6.2. Edit tests and test records
- 85 10.6.3. Test details
- 86 10.6.4. Graphs
- 87 10.7. Produce and print reports
- 87 10.7.1. Set up header and footer
- 88 10.7.2. Define test selection
- 88 10.7.3. Print
- 89 10.8. Online Help
- 90 LANTEK Firmware Upgrade
- 90 11.1. Perform Firmware Upgrade
- 90 11.1.1. Using the Computer
- 91 11.1.2. Firmware Upgrade with USB Removable Storage
- 92 Specifications
- 92 12.1. Fiber (LWL)
- 94 Customer Service
- 94 13.1. Technical Support
- 94 13.2. Service in the US
- 94 13.3. Service outside the US
- 96 13.4. Internet