![](http://s3.manualzz.com/store/data/024068748_1-9106a75f729f3ead368472ee734908a9-128x128.png)
advertisement
![Modular RAID Controllers | Manualzz Modular RAID Controllers | Manualzz](http://s3.manualzz.com/store/data/024068748_1-9106a75f729f3ead368472ee734908a9-360x466.png)
Modular RAID 12Gb/s (SAS3.0)
Connectors
Connector Type
SAS MLC1 x4 SAS, ports 0- 3
SAS MLC2 x4 SAS, ports 4- 7
HDD LED
FBU
Hard drive activity indication LED
1-6
Description
SFF 8643 Mini SAS HD 4i connector for SAS
IO cable to backplane and hard drives
SFF 8643 Mini SAS HD 4i connector for SAS
IO cable to backplane and hard drives
6-pin connector
Pin 4 to connect activity LED
Connector on TFM to attach FBU
Indicators
LED
L1 (green blinking)
Description
Heart Beat
5.1.4
Installation
This section describes how to install the SAS RAID controller in a server.
V
CAUTION!
To safeguard against data loss, remember to back up your data before you change your system configuration.
To install the new controller, proceed as follows:
Step 1 Unpack the controller
Unpack the new controller in a static-free environment. Remove it from the anti-static bag and inspect it for damage.
If the controller appears to be damaged, contact the Fujitsu support service.
Step 2 Prepare the server
Turn off the server and remove the cover from the chassis.
78
Modular
Modular RAID 12Gb/s (SAS3.0)
Step 3
Step 4
Step 5
Step 6
Install the new SAS RAID controller
Insert the controller in a suitable PCI Express slot on the system board. Press down gently but firmly to ensure the controller is properly seated in the slot. Secure the controller to the computer chassis with the PCI card hold down latches. Connect the SAS and/or SATA HDDs located in the system to the SAS cable connector(s) on the controller. Refer to your server specific
Upgrade and Maintenance Manual for information on the PCI
Express slot and installing the controller.
Power-up the computer
Replace the computer cover and reconnect the power cable(s).
Start up the computer. Ensure that the SAS and/or SATA II devices are properly connected to the controller.
During booting, a message similar to the following is displayed:
LSI MegaRAID SAS-MFI BIOS Version NTxx (Build ..date..)
Copyright(c) 2014, LSI Corporation
HA-x (Bus x Dev y) PRAID EP400i / EP420i (D3216)
FW package: xxxx
Run the BIOS Configuration Utility
Run the BIOS Configuration Utility to configure the physical arrays and logical drives. Press CTRL+R immediately to run the utility, when the following message appears on the screen:
Press <Ctrl><R> to Run MegaRAID Configuration Utility
Install the operating system driver
The controller can operate under various operating systems. To use these operating systems, you must install software drivers.
The ServerView Suite DVD 1 includes drivers for the supported operating systems, along with documentation. You can view the supported operating systems and download the latest drivers for
RAID adapters on the website at:
http://ts.fujitsu.com/support/
For Japan please use the URL:
http://www.fujitsu.com/jp/products/computing/servers/primergy/
Modular RAID Controllers
79
advertisement
Related manuals
advertisement
Table of contents
- 7 Introduction
- 7 Requirements
- 7 Further information
- 8 Notational conventions
- 9 Important information
- 9 Safety instructions
- 11 CE certificate
- 12 Environmental protection
- 15 Modular RAID 3Gb/s (SAS1.0)
- 15 (D2507)
- 16 Features
- 16 Controller versions
- 17 Connectors
- 18 Installation
- 21 (D2516)
- 21 Features
- 22 Controller versions
- 23 Connectors and indicators
- 24 Installation
- 27 Installing an optional iBBU module
- 27 Features
- 27 Installation
- 31 Modular RAID 6Gb/s (SAS2.0)
- 31 RAID controller "RAID Ctrl SAS 6G 0/1 (D2607)
- 32 Features
- 33 Controller versions
- 33 Connectors and indicators
- 34 Installation
- 37 RAID Controller "RAID Ctrl SAS 6G 5/6 512 MB (D2616)
- 38 Features
- 39 Controller versions
- 39 Connectors and indicators
- 41 Installation
- 44 Installing an optional iBBU module
- 44 Features
- 44 Installation
- 47 RAID Controller "PY SAS RAID Mezz Card 6 Gb (D3016)
- 48 Features
- 48 Controller versions
- 49 Connectors and indicators
- 50 Installation
- 52 Installing an optional iBBU module
- 52 Features
- 52 Installation
- 54 RAID Controller "RAID Ctrl SAS 6G 1GB (D3116)
- 55 Features
- 56 Controller versions
- 56 Connectors and indicators
- 58 Installation
- 60 Installing an optional TFM / FBU module
- 60 Features
- 60 Installation
- 63 RAID Controller "PY SAS RAID HDD Module (D2816)
- 64 Features
- 65 Controller versions
- 65 Connectors and indicators
- 66 Installation
- 68 Installing an optional FBU module
- 68 Features
- 68 Installation
- 70 (D2837)
- 71 Features
- 71 Controller versions
- 72 Connectors and indicators
- 73 Installation
- 75 Modular RAID 12Gb/s (SAS3.0)
- 75 RAID Controller "PRAID EP400i / EP420i
- 76 Features
- 76 Controller versions
- 77 Connectors and indicators
- 78 Installation
- 80 Installing an optional TFM / FBU module
- 80 Features
- 80 Installation
- 85 RAID Controller "PRAID EM400i
- 86 Features
- 86 Controller versions
- 87 Connectors and indicators
- 88 Installation
- 90 RAID Controller "PRAID CM400i
- 91 Features
- 91 Controller versions
- 92 Connectors and indicators
- 93 Installation
- 95 RAID Controller "PRAID CP400i
- 96 Features
- 96 Controller versions
- 97 Connectors and indicators
- 98 Installation
- 100 RAID Controller "PRAID EP420e
- 101 Features
- 102 Controller versions
- 103 Connectors and jumpers
- 104 Installation
- 106 Installing an optional TFM / FBU module
- 107 RAID Controller "PRAID EP440i
- 108 Features
- 109 Controller versions
- 109 Connectors and indicators
- 111 Installation
- 113 Installing an optional FBU module